px4-firmware/nuttx/drivers/wireless/cc1101/ISM1_868MHzGFSK100kbps.c

114 lines
5.1 KiB
C
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

/****************************************************************************
* drivers/wireless/cc1101/ISM1_868MHzGFSK100kbps.c
*
* Copyright (C) 2011 Uros Platise. All rights reserved.
* Copyright (C) 2011 Ales Verbic. All rights reserved.
*
* Authors: Uros Platise <uros.platise@isotel.eu>
* Ales Verbic <ales.verbic@isotel.eu>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
#include <nuttx/wireless/cc1101.h>
/** Settings for 868 MHz, GFSK at 100kbps
*
* ISM Region 1 (Europe) only, Band 868870 MHz
*
* Frequency ERP Duty Cycle Bandwidth Remarks
* 868 868.6 MHz +14 dBm < 1% No limits
* 868.7 869.2 MHz +14 dBm < 0.1% No limits
* 869.3 869.4 MHz +10 dBm No limits < 25 kHz Appropriate access protocol required
* 869.4 869.65 MHz +27 dBm < 10% < 25 kHz Channels may be combined to one high speed channel
* 869.7 -870 MHz +7 dBm No limits No limits
*
* Deviation = 46.142578
* Base frequency = 867.999985
* Carrier frequency = 867.999985
* Channel number = 0
* Carrier frequency = 867.999985
* Modulated = true
* Modulation format = GFSK
* Manchester enable = false
* Sync word qualifier mode = 30/32 sync word bits detected
* Preamble count = 4
* Channel spacing = 199.813843
* Carrier frequency = 867.999985
* Data rate = 99.9069
* RX filter BW = 210.937500
* Data format = Normal mode
* Length config = Fixed packet length mode. Length configured in PKTLEN register
* CRC enable = true
* Packet length = 62
* Device address = 00
* Address config = NO Address check, no broadcast
* CRC autoflush = true
* PA ramping = false
* TX power = 0
*/
const struct c1101_rfsettings_s cc1101_rfsettings_ISM1_868MHzGFSK100kbps = {
.FSCTRL1 = 0x08, // FSCTRL1 Frequency Synthesizer Control
.FSCTRL0 = 0x00, // FSCTRL0 Frequency Synthesizer Control
.FREQ2 = 0x20, // FREQ2 Frequency Control Word, High Byte
.FREQ1 = 0x25, // FREQ1 Frequency Control Word, Middle Byte
.FREQ0 = 0xED, // FREQ0 Frequency Control Word, Low Byte
.MDMCFG4 = 0x8B, // MDMCFG4 Modem Configuration
.MDMCFG3 = 0xE5, // MDMCFG3 Modem Configuration
.MDMCFG2 = 0x13, // MDMCFG2 Modem Configuration
.MDMCFG1 = 0x22, // MDMCFG1 Modem Configuration
.MDMCFG0 = 0xE5, // MDMCFG0 Modem Configuration
.DEVIATN = 0x46, // DEVIATN Modem Deviation Setting
.FOCCFG = 0x1D, // FOCCFG Frequency Offset Compensation Configuration
.BSCFG = 0x1C, // BSCFG Bit Synchronization Configuration
.AGCCTRL2= 0xC7, // AGCCTRL2 AGC Control
.AGCCTRL1= 0x00, // AGCCTRL1 AGC Control
.AGCCTRL0= 0xB2, // AGCCTRL0 AGC Control
.FREND1 = 0xB6, // FREND1 Front End RX Configuration
.FREND0 = 0x10, // FREND0 Front End TX Configuration
.FSCAL3 = 0xEA, // FSCAL3 Frequency Synthesizer Calibration
.FSCAL2 = 0x2A, // FSCAL2 Frequency Synthesizer Calibration
.FSCAL1 = 0x00, // FSCAL1 Frequency Synthesizer Calibration
.FSCAL0 = 0x1F, // FSCAL0 Frequency Synthesizer Calibration
.CHMIN = 0, // Fix at 9th channel: 869.80 MHz +- 100 kHz RF Bandwidth
.CHMAX = 9, // single channel
.PAMAX = 8, // 0 means power OFF, 8 represents PA[7]
.PA = {0x03, 0x0F, 0x1E, 0x27, 0x67, 0x50, 0x81, 0xC2}
};