dark0707
/
px4-firmware
forked from Archive/PX4-Autopilot
1
0
Fork 0
Code Pull Requests Activity
px4-firmware/boards/modalai/fc-v1/nuttx-config/include/board.h

483 lines
19 KiB
C
Raw Blame History

/************************************************************************************
* nuttx-configs/modalai_fcv1/include/board.h
*
* Copyright (C) 2016-2019 Gregory Nutt. All rights reserved.
* Authors: David Sidrane <david_s5@nscdg.com>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __NUTTX_CONFIG_MODALAI_FCV1_INCLUDE_BOARD_H
#define __NUTTX_CONFIG_MODALAI_FCV1_INCLUDE_BOARD_H
/************************************************************************************
* Included Files
************************************************************************************/
#include "board_dma_map.h"
#include <nuttx/config.h>
#ifndef __ASSEMBLY__
# include <stdint.h>
#endif
#include "stm32_rcc.h"
#include "stm32_sdmmc.h"
/************************************************************************************
* Pre-processor Definitions
************************************************************************************/
/* Clocking *************************************************************************/
/* The modalai_fcv1 board provides the following clock sources:
*
* X301: 16 MHz crystal for HSE
*
* So we have these clock source available within the STM32
*
* HSI: 16 MHz RC factory-trimmed
* HSE: 16 MHz crystal for HSE
*/
#define STM32_BOARD_XTAL 16000000ul
#define STM32_HSI_FREQUENCY 16000000ul
#define STM32_LSI_FREQUENCY 32000
#define STM32_HSE_FREQUENCY STM32_BOARD_XTAL
#define STM32_LSE_FREQUENCY 0
/* Main PLL Configuration.
*
* PLL source is HSE = 16,000,000
*
* PLL_VCO = (STM32_HSE_FREQUENCY / PLLM) * PLLN
* Subject to:
*
* 2 <= PLLM <= 63
* 192 <= PLLN <= 432
* 192 MHz <= PLL_VCO <= 432MHz
*
* SYSCLK = PLL_VCO / PLLP
* Subject to
*
* PLLP = {2, 4, 6, 8}
* SYSCLK <= 216 MHz
*
* USB OTG FS, SDMMC and RNG Clock = PLL_VCO / PLLQ
* Subject to
* The USB OTG FS requires a 48 MHz clock to work correctly. The SDMMC
* and the random number generator need a frequency lower than or equal
* to 48 MHz to work correctly.
*
* 2 <= PLLQ <= 15
*/
/* Highest SYSCLK with USB OTG FS clock = 48 MHz
*
* PLL_VCO = (16,000,000 / 8) * 216 = 432 MHz
* SYSCLK = 432 MHz / 2 = 216 MHz
* USB OTG FS, SDMMC and RNG Clock = 432 MHz / 9 = 48 MHz
*/
#define STM32_PLLCFG_PLLM RCC_PLLCFG_PLLM(8)
#define STM32_PLLCFG_PLLN RCC_PLLCFG_PLLN(216)
#define STM32_PLLCFG_PLLP RCC_PLLCFG_PLLP_2
#define STM32_PLLCFG_PLLQ RCC_PLLCFG_PLLQ(9)
#define STM32_VCO_FREQUENCY ((STM32_HSE_FREQUENCY / 8) * 216)
#define STM32_SYSCLK_FREQUENCY (STM32_VCO_FREQUENCY / 2)
#define STM32_OTGFS_FREQUENCY (STM32_VCO_FREQUENCY / 9)
/* Configure factors for PLLSAI clock */
#define CONFIG_STM32F7_PLLSAI 1
#define STM32_RCC_PLLSAICFGR_PLLSAIN RCC_PLLSAICFGR_PLLSAIN(192)
#define STM32_RCC_PLLSAICFGR_PLLSAIP RCC_PLLSAICFGR_PLLSAIP(8)
#define STM32_RCC_PLLSAICFGR_PLLSAIQ RCC_PLLSAICFGR_PLLSAIQ(4)
#define STM32_RCC_PLLSAICFGR_PLLSAIR RCC_PLLSAICFGR_PLLSAIR(2)
/* Configure Dedicated Clock Configuration Register */
#define STM32_RCC_DCKCFGR1_PLLI2SDIVQ RCC_DCKCFGR1_PLLI2SDIVQ(1)
#define STM32_RCC_DCKCFGR1_PLLSAIDIVQ RCC_DCKCFGR1_PLLSAIDIVQ(1)
#define STM32_RCC_DCKCFGR1_PLLSAIDIVR RCC_DCKCFGR1_PLLSAIDIVR(0)
#define STM32_RCC_DCKCFGR1_SAI1SRC RCC_DCKCFGR1_SAI1SEL(0)
#define STM32_RCC_DCKCFGR1_SAI2SRC RCC_DCKCFGR1_SAI2SEL(0)
#define STM32_RCC_DCKCFGR1_TIMPRESRC 0
#define STM32_RCC_DCKCFGR1_DFSDM1SRC 0
#define STM32_RCC_DCKCFGR1_ADFSDM1SRC 0
/* Configure factors for PLLI2S clock */
#define CONFIG_STM32F7_PLLI2S 1
#define STM32_RCC_PLLI2SCFGR_PLLI2SN RCC_PLLI2SCFGR_PLLI2SN(192)
#define STM32_RCC_PLLI2SCFGR_PLLI2SP RCC_PLLI2SCFGR_PLLI2SP(2)
#define STM32_RCC_PLLI2SCFGR_PLLI2SQ RCC_PLLI2SCFGR_PLLI2SQ(2)
#define STM32_RCC_PLLI2SCFGR_PLLI2SR RCC_PLLI2SCFGR_PLLI2SR(2)
/* Configure Dedicated Clock Configuration Register 2 */
#define STM32_RCC_DCKCFGR2_USART1SRC RCC_DCKCFGR2_USART1SEL_APB
#define STM32_RCC_DCKCFGR2_USART2SRC RCC_DCKCFGR2_USART2SEL_APB
#define STM32_RCC_DCKCFGR2_UART4SRC RCC_DCKCFGR2_UART4SEL_APB
#define STM32_RCC_DCKCFGR2_UART5SRC RCC_DCKCFGR2_UART5SEL_APB
#define STM32_RCC_DCKCFGR2_USART6SRC RCC_DCKCFGR2_USART6SEL_APB
#define STM32_RCC_DCKCFGR2_UART7SRC RCC_DCKCFGR2_UART7SEL_APB
#define STM32_RCC_DCKCFGR2_UART8SRC RCC_DCKCFGR2_UART8SEL_APB
#define STM32_RCC_DCKCFGR2_I2C1SRC RCC_DCKCFGR2_I2C1SEL_HSI
#define STM32_RCC_DCKCFGR2_I2C2SRC RCC_DCKCFGR2_I2C2SEL_HSI
#define STM32_RCC_DCKCFGR2_I2C3SRC RCC_DCKCFGR2_I2C3SEL_HSI
#define STM32_RCC_DCKCFGR2_I2C4SRC RCC_DCKCFGR2_I2C4SEL_HSI
#define STM32_RCC_DCKCFGR2_LPTIM1SRC RCC_DCKCFGR2_LPTIM1SEL_APB
#define STM32_RCC_DCKCFGR2_CECSRC RCC_DCKCFGR2_CECSEL_HSI
#define STM32_RCC_DCKCFGR2_CK48MSRC RCC_DCKCFGR2_CK48MSEL_PLL
#define STM32_RCC_DCKCFGR2_SDMMCSRC RCC_DCKCFGR2_SDMMCSEL_48MHZ
#define STM32_RCC_DCKCFGR2_SDMMC2SRC RCC_DCKCFGR2_SDMMC2SEL_48MHZ
#define STM32_RCC_DCKCFGR2_DSISRC RCC_DCKCFGR2_DSISEL_PHY
/* Several prescalers allow the configuration of the two AHB buses, the
* high-speed APB (APB2) and the low-speed APB (APB1) domains. The maximum
* frequency of the two AHB buses is 216 MHz while the maximum frequency of
* the high-speed APB domains is 108 MHz. The maximum allowed frequency of
* the low-speed APB domain is 54 MHz.
*/
/* AHB clock (HCLK) is SYSCLK (216 MHz) */
#define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK /* HCLK = SYSCLK / 1 */
#define STM32_HCLK_FREQUENCY STM32_SYSCLK_FREQUENCY
#define STM32_BOARD_HCLK STM32_HCLK_FREQUENCY /* same as above, to satisfy compiler */
/* APB1 clock (PCLK1) is HCLK/4 (54 MHz) */
#define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd4 /* PCLK1 = HCLK / 4 */
#define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/4)
/* Timers driven from APB1 will be twice PCLK1 */
#define STM32_APB1_TIM2_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM3_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM4_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM5_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM6_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM7_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM12_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM13_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM14_CLKIN (2*STM32_PCLK1_FREQUENCY)
/* APB2 clock (PCLK2) is HCLK/2 (108MHz) */
#define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLKd2 /* PCLK2 = HCLK / 2 */
#define STM32_PCLK2_FREQUENCY (STM32_HCLK_FREQUENCY/2)
/* Timers driven from APB2 will be twice PCLK2 */
#define STM32_APB2_TIM1_CLKIN (2*STM32_PCLK2_FREQUENCY)
#define STM32_APB2_TIM8_CLKIN (2*STM32_PCLK2_FREQUENCY)
#define STM32_APB2_TIM9_CLKIN (2*STM32_PCLK2_FREQUENCY)
#define STM32_APB2_TIM10_CLKIN (2*STM32_PCLK2_FREQUENCY)
#define STM32_APB2_TIM11_CLKIN (2*STM32_PCLK2_FREQUENCY)
/* SDMMC dividers. Note that slower clocking is required when DMA is disabled
* in order to avoid RX overrun/TX underrun errors due to delayed responses
* to service FIFOs in interrupt driven mode. These values have not been
* tuned!!!
*
* SDMMCCLK=48MHz, SDMMC_CK=SDMMCCLK/(118+2)=400 KHz
*/
/* Use the Falling edge of the SDIO_CLK clock to change the edge the
* data and commands are change on
*/
#define STM32_SDMMC_CLKCR_EDGE STM32_SDMMC_CLKCR_NEGEDGE
#define STM32_SDMMC_INIT_CLKDIV (118 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
/* DMA ON: SDMMCCLK=48MHz, SDMMC_CK=SDMMCCLK/(1+2)=16 MHz
* DMA OFF: SDMMCCLK=48MHz, SDMMC_CK=SDMMCCLK/(2+2)=12 MHz
*/
#ifdef CONFIG_STM32F7_SDMMC_DMA
# define STM32_SDMMC_MMCXFR_CLKDIV (1 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
#else
# define STM32_SDMMC_MMCXFR_CLKDIV (2 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
#endif
/* DMA ON: SDMMCCLK=48MHz, SDMMC_CK=SDMMCCLK/(1+2)=16 MHz
* DMA OFF: SDMMCCLK=48MHz, SDMMC_CK=SDMMCCLK/(2+2)=12 MHz
*/
//TODO #warning "Check Freq for 24mHz"
#ifdef CONFIG_STM32F7_SDMMC_DMA
# define STM32_SDMMC_SDXFR_CLKDIV (1 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
#else
# define STM32_SDMMC_SDXFR_CLKDIV (2 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
#endif
/* FLASH wait states
*
* --------- ---------- -----------
* VDD MAX SYSCLK WAIT STATES
* --------- ---------- -----------
* 1.7-2.1 V 180 MHz 8
* 2.1-2.4 V 216 MHz 9
* 2.4-2.7 V 216 MHz 8
* 2.7-3.6 V 216 MHz 7
* --------- ---------- -----------
*/
#define BOARD_FLASH_WAITSTATES 7
/* LED definitions ******************************************************************/
/* The modalai_fcv1 board has numerous LEDs but only three, LED_GREEN a Green LED, LED_BLUE
* a Blue LED and LED_RED a Red LED, that can be controlled by software.
*
* If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in any way.
* The following definitions are used to access individual LEDs.
*/
/* LED index values for use with board_userled() */
#define BOARD_LED1 0
#define BOARD_LED2 1
#define BOARD_LED3 2
#define BOARD_NLEDS 3
#define BOARD_LED_RED BOARD_LED1
#define BOARD_LED_GREEN BOARD_LED2
#define BOARD_LED_BLUE BOARD_LED3
/* LED bits for use with board_userled_all() */
#define BOARD_LED1_BIT (1 << BOARD_LED1)
#define BOARD_LED2_BIT (1 << BOARD_LED2)
#define BOARD_LED3_BIT (1 << BOARD_LED3)
/* If CONFIG_ARCH_LEDS is defined, the usage by the board port is defined in
* include/board.h and src/stm32_leds.c. The LEDs are used to encode OS-related
* events as follows:
*
*
* SYMBOL Meaning LED state
* Red Green Blue
* ---------------------- -------------------------- ------ ------ ----*/
#define LED_STARTED 0 /* NuttX has been started OFF OFF OFF */
#define LED_HEAPALLOCATE 1 /* Heap has been allocated OFF OFF ON */
#define LED_IRQSENABLED 2 /* Interrupts enabled OFF ON OFF */
#define LED_STACKCREATED 3 /* Idle stack created OFF ON ON */
#define LED_INIRQ 4 /* In an interrupt N/C N/C GLOW */
#define LED_SIGNAL 5 /* In a signal handler N/C GLOW N/C */
#define LED_ASSERTION 6 /* An assertion failed GLOW N/C GLOW */
#define LED_PANIC 7 /* The system has crashed Blink OFF N/C */
#define LED_IDLE 8 /* MCU is is sleep mode ON OFF OFF */
/* Thus if the Green LED is statically on, NuttX has successfully booted and
* is, apparently, running normally. If the Red LED is flashing at
* approximately 2Hz, then a fatal error has been detected and the system
* has halted.
*/
/* Alternate function pin selections ************************************************/
#define GPIO_USART1_RX GPIO_USART1_RX_3 /* PB15 */
#define GPIO_USART1_TX GPIO_USART1_TX_3 /* PB14 */
#define GPIO_USART2_RX GPIO_USART2_RX_1 /* PA3 */
#define GPIO_USART2_TX GPIO_USART2_TX_2 /* PD5 */
#define GPIO_USART2_RTS GPIO_USART2_RTS_2 /* PD4 */
#define GPIO_USART2_CTS GPIO_USART2_CTS_2 /* PD3 */
#define GPIO_USART3_RX GPIO_USART3_RX_3 /* PD9 */
#define GPIO_USART3_TX GPIO_USART3_TX_3 /* PD8 */
#define GPIO_UART4_RX GPIO_UART4_RX_5 /* PH14 */
#define GPIO_UART4_TX GPIO_UART4_TX_5 /* PH13 */
#define GPIO_UART5_RX GPIO_UART5_RX_1 /* PD2 */
#define GPIO_UART5_TX GPIO_UART5_TX_4 /* PB9 */
#define GPIO_UART5_RTS GPIO_UART5_RTS_1 /* PC8 */
#define GPIO_UART5_CTS GPIO_UART5_CTS_1 /* PC9 */
#define GPIO_USART6_RX GPIO_USART6_RX_1 /* PC 7 */
#define GPIO_USART6_TX GPIO_USART6_TX_1 /* PC6 */
#define GPIO_UART7_RX GPIO_UART7_RX_1 /* PE7 */
#define GPIO_UART7_TX GPIO_UART7_TX_1 /* PE8 */
#define GPIO_UART7_RTS GPIO_UART7_RTS_1 /* PE9 */
#define GPIO_UART7_CTS GPIO_UART7_CTS_1 /* PE10 */
/* UART8: has no remap
*
* GPIO_UART8_RX PE0
* GPIO_UART8_TX PE1
*/
/* CAN
*
* CAN1 is routed to transceiver.
* CAN2 is routed to transceiver.
*/
#define GPIO_CAN1_RX GPIO_CAN1_RX_3 /* PD0 */
#define GPIO_CAN1_TX GPIO_CAN1_TX_3 /* PD1 */
#define GPIO_CAN2_RX GPIO_CAN2_RX_1 /* PB12 */
#define GPIO_CAN2_TX GPIO_CAN2_TX_2 /* PB6 */
/* SPI
* SPI1 is IMU 20648 (Rev A)
* SPI2 is none (Rev A)
* SPI3 is none (Rev A)
* SPI4 is none (Rev A)
* SPI5 is FRAM
* SPI6 is none (Rev A)
*
*/
#define GPIO_SPI1_MISO GPIO_SPI1_MISO_2 /* PB4 */
#define GPIO_SPI1_MOSI GPIO_SPI1_MOSI_2 /* PB5 */
#define GPIO_SPI1_SCK GPIO_SPI1_SCK_1 /* PA5 */
#define GPIO_SPI2_MISO GPIO_SPI2_MISO_3 /* PI2 */
#define GPIO_SPI2_MOSI GPIO_SPI2_MOSI_3 /* PI3 */
#define GPIO_SPI2_SCK GPIO_SPI2_SCK_5 /* PI1 */
#define GPIO_SPI3_MISO GPIO_SPI3_MISO_2 /* PC11 */
#define GPIO_SPI3_MOSI GPIO_SPI3_MOSI_1 /* PB2 */
#define GPIO_SPI3_SCK GPIO_SPI3_SCK_2 /* PC10 */
#define GPIO_SPI4_MISO GPIO_SPI4_MISO_2 /* PE13 */
#define GPIO_SPI4_MOSI GPIO_SPI4_MOSI_1 /* PE6 */
#define GPIO_SPI4_SCK GPIO_SPI4_SCK_2 /* PE12 */
#define GPIO_SPI5_MISO GPIO_SPI5_MISO_1 /* PF8 */
#define GPIO_SPI5_MOSI GPIO_SPI5_MOSI_2 /* PF11 */
#define GPIO_SPI5_SCK GPIO_SPI5_SCK_1 /* PF7 */
#define GPIO_SPI6_MISO GPIO_SPI6_MISO_2 /* PA6 */
#define GPIO_SPI6_MOSI GPIO_SPI6_MOSI_1 /* PG14 */
#define GPIO_SPI6_SCK GPIO_SPI6_SCK_3 /* PB3 */
/* I2C
*
* The optional _GPIO configurations allow the I2C driver to manually
* reset the bus to clear stuck slaves. They match the pin configuration,
* but are normally-high GPIOs.
*
*/
#define GPIO_I2C1_SCL GPIO_I2C1_SCL_2 /* PB8 */
#define GPIO_I2C1_SDA GPIO_I2C1_SDA_1 /* PB7 */
#define GPIO_I2C1_SCL_GPIO (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN8)
#define GPIO_I2C1_SDA_GPIO (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN7)
#define GPIO_I2C2_SCL GPIO_I2C2_SCL_2 /* PF1 */
#define GPIO_I2C2_SDA GPIO_I2C2_SDA_2 /* PF0 */
#define GPIO_I2C2_SCL_GPIO (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTF | GPIO_PIN1)
#define GPIO_I2C2_SDA_GPIO (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTF | GPIO_PIN0)
#define GPIO_I2C3_SCL GPIO_I2C3_SCL_2 /* PH7 */
#define GPIO_I2C3_SDA GPIO_I2C3_SDA_2 /* PH8 */
#define GPIO_I2C3_SCL_GPIO (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTH | GPIO_PIN7)
#define GPIO_I2C3_SDA_GPIO (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTH | GPIO_PIN8)
#define GPIO_I2C4_SCL GPIO_I2C4_SCL_2 /* PF14 */
#define GPIO_I2C4_SDA GPIO_I2C4_SDA_2 /* PF15 */
#define GPIO_I2C4_SCL_GPIO (GPIO_OUTPUT | GPIO_OPENDRAIN | GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTF | GPIO_PIN14)
#define GPIO_I2C4_SDA_GPIO (GPIO_OUTPUT | GPIO_OPENDRAIN | GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTF | GPIO_PIN15)
/* SDMMC2
*
* VDD 3.3
* GND
* SDMMC2_CK PD6
* SDMMC2_CMD PD7
* SDMMC2_D0 PG9
* SDMMC2_D1 PG10
* SDMMC2_D2 PG11
* SDMMC2_D3 PG12
*/
#define GPIO_SDMMC2_D0 GPIO_SDMMC2_D0_2
#define GPIO_SDMMC2_D1 GPIO_SDMMC2_D1_2
#define GPIO_SDMMC2_D2 GPIO_SDMMC2_D2_2
#define GPIO_SDMMC2_D3 GPIO_SDMMC2_D3_2
/* USB
*
* OTG_FS_DM PA11
* OTG_FS_DP PA12
* VBUS PA9
*/
/* Board provides GPIO or other Hardware for signaling to timing analyzer */
#if defined(CONFIG_BOARD_USE_PROBES)
# include "stm32_gpio.h"
# define PROBE_N(n) (1<<((n)-1))
# define PROBE_1 (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTE|GPIO_PIN14) /* PE14 AUX1 */
# define PROBE_2 (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN10) /* PA10 AUX2 */
# define PROBE_3 (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTE|GPIO_PIN11) /* PE11 AUX3 */
# define PROBE_4 (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN8) /* PA8 AUX4 */
# define PROBE_5 (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN13) /* PD13 AUX5 */
# define PROBE_6 (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN14) /* PD14 AUX6 */
# define PROBE_7 (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTH|GPIO_PIN6) /* PH6 AUX7 */
# define PROBE_8 (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTH|GPIO_PIN9) /* PH9 AUX8 */
# define PROBE_9 (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTI|GPIO_PIN0) /* PI0 CAP1 */
# define PROBE_INIT(mask) \
do { \
if ((mask)& PROBE_N(1)) { stm32_configgpio(PROBE_1); } \
if ((mask)& PROBE_N(2)) { stm32_configgpio(PROBE_2); } \
if ((mask)& PROBE_N(3)) { stm32_configgpio(PROBE_3); } \
if ((mask)& PROBE_N(4)) { stm32_configgpio(PROBE_4); } \
if ((mask)& PROBE_N(5)) { stm32_configgpio(PROBE_5); } \
if ((mask)& PROBE_N(6)) { stm32_configgpio(PROBE_6); } \
if ((mask)& PROBE_N(7)) { stm32_configgpio(PROBE_7); } \
if ((mask)& PROBE_N(8)) { stm32_configgpio(PROBE_8); } \
if ((mask)& PROBE_N(9)) { stm32_configgpio(PROBE_9); } \
} while(0)
# define PROBE(n,s) do {stm32_gpiowrite(PROBE_##n,(s));}while(0)
# define PROBE_MARK(n) PROBE(n,false);PROBE(n,true)
#else
# define PROBE_INIT(mask)
# define PROBE(n,s)
# define PROBE_MARK(n)
#endif
#endif /*__NUTTX_CONFIG_MODALAI_FCV1_INCLUDE_BOARD_H */
View Git Blame Copy Permalink