forked from Archive/PX4-Autopilot
62 lines
1.8 KiB
INI
62 lines
1.8 KiB
INI
#daemon configuration
|
|
telnet_port 4444
|
|
gdb_port 3333
|
|
|
|
#interface
|
|
interface ft2232
|
|
ft2232_device_desc "Olimex OpenOCD JTAG ARM-USB-TINY-H"
|
|
ft2232_layout "olimex-jtag"
|
|
ft2232_vid_pid 0x15ba 0x002a
|
|
|
|
# NXP LPC1768 Cortex-M3 with 512kB Flash and 32kB+32kB Local On-Chip SRAM, clocked with 4MHz internal RC oscillator
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME lpc1768
|
|
}
|
|
|
|
if { [info exists ENDIAN] } {
|
|
set _ENDIAN $ENDIAN
|
|
} else {
|
|
set _ENDIAN little
|
|
}
|
|
|
|
if { [info exists CPUTAPID ] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
set _CPUTAPID 0x4ba00477
|
|
}
|
|
|
|
#delays on reset lines
|
|
jtag_nsrst_delay 200
|
|
jtag_ntrst_delay 200
|
|
|
|
# LPC2000 & LPC1700 -> SRST causes TRST
|
|
reset_config trst_and_srst srst_pulls_trst
|
|
|
|
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME
|
|
|
|
# LPC1768 has 32kB of SRAM on its main system bus (so-called Local On-Chip SRAM)
|
|
$_TARGETNAME configure -work-area-phys 0x10000000 -work-area-size 0x8000 -work-area-backup 0
|
|
|
|
# REVISIT is there any good reason to have this reset-init event handler??
|
|
# Normally they should set up (board-specific) clocking then probe the flash...
|
|
$_TARGETNAME configure -event reset-init {
|
|
# Force NVIC.VTOR to point to flash at 0 ...
|
|
# WHY? This is it's reset value; we run right after reset!!
|
|
mwb 0xE000ED08 0x00
|
|
}
|
|
|
|
# LPC1768 has 512kB of user-available FLASH (bootloader is located in separate dedicated region).
|
|
# flash bank lpc1700 <base> <size> 0 0 <target#> <variant> <cclk> [calc_checksum]
|
|
|
|
set _FLASHNAME $_CHIPNAME.flash
|
|
flash bank $_FLASHNAME lpc2000 0x0 0x80000 0 0 $_TARGETNAME lpc1700 80000 calc_checksum
|
|
|
|
# 4MHz / 6 = 666kHz, so use 500
|
|
jtag_khz 500
|