px4-firmware/nuttx/configs/z16f2800100zcog

README.txt
^^^^^^^^^^

This is the README file for the NuttX port to the ZiLog ZNEO MCU.

ZDS-II Compiler Versions
^^^^^^^^^^^^^^^^^^^^^^^^

Version 4.10.2

  The ZDS-II version 4.10.2 will not compile NuttX.  It reports "internal
  errors" on some of the files.  Upgrades to ZDS-II are available for
  download from the Zilog website: http://www.zilog.com/software/zds2.asp

Version 4.11.0

  NuttX compiles correctly with the newer 4.11.0 version of the ZDS-II
  toolchain.  However, I have found a few issues:

  - The code will not run without the -reduceopt option.  There is,
    apparently, some optimization related issue.  This issue has not
    been analyzed as of this writing.

  - Not all NuttX logic will not run with the -regvars option.  There is
    at least one failure that has been reported to ZiLOG as incident 81400.

  - The Pascal add-on interpreter includes a large switch statement and
    exposes another compiler problem.  This is reported as incident 81459.

Version 4.11.1

  As of this writing (30 September 2010), the latest release of ZDS-II for the
  ZNEO is 4.11.1.  It is unknown if this release includes fixes for incidents
  81400 and 81459 or not.  It is unknown if the code will run without -reduceopt
  either. (Basically, it compiles with 4.11.1, but is untested with that version).

Version 5.0.1

  On November 29, 2012, all of the z16f configurations were converted to use 5.0.1,
  but have not been verified on a running target.

  Paths were also updated that are specific to a 32-bit toolchain running on
  a 64 bit windows platform.  Change to a different toolchain, you will need
  to modify the versioning in Make.defs and setenv.sh; if you want to build
  on a different platform, you will need to change the path in the ZDS binaries
  in those same files.
  
Other Versions

  If you use any version of ZDS-II other than 5.0.1 or if you install ZDS-II
  at any location other than the default location, you will have to modify
  two files:  (1) configs/z16f2800100zcog/*/setenv.sh and (2)
  configs/z16f2800100zcog/*/Make.defs.  Simply edit these two files, changing
  5.0.1 to whatever.

Issues
^^^^^^

There are several, important open issues with the ZNEO port (8 as of this writing).
See the TODO file in the top-level NuttX directory.  One of these should be
mentioned here because it causes a failure to compile Nuttx:

  Description: The file drivers/mmcsd/mmcsd_sdio.c generates an internal compiler
               error like:
 
               mmcsd\mmcsd_sdio.c
               Internal Error(0503) On line 2524 of "MMCSD\MMCSD_SDIO.C"
                   File <c3>, Args(562,46)

  Status:     Open.  Recommended workaround: remove mmcsd_sdio.c from
              drivers/mmcsd/Make.defs.  There is no SDIO support for the Z16 anyway
  Priority:   Low

This is bug in ZDS-II.  It was discovered in version 4.11.0 and still exists
in version 4.11.1.

Configuration Subdirectories
^^^^^^^^^^^^^^^^^^^^^^^^^^^^

- source/ and include/
    These directories contain common logic for all z16f2800100zcog
    configurations.

Variations on the basic z8f162800100zcog configuration are maintained
in subdirectories.  To configure any specific configuration, do the
following steps:

   cd <nuttx-top-directory>/tools
   ./configure.sh z16f2800100zcog/<sub-directory>
   cd <nuttx-top-directory>
   make

Where <sub-directory> is the specific board configuration that you
wish to build.  The following board-specific configurations are
available:

ostest
------

    This builds the examples/ostest application for execution from FLASH.
    See examples/README.txt for information about ostest.

    NOTES:

    1. This configuration uses the mconf-based configuration tool.  To
       change this configuration using that tool, you should:

       a. Build and install the kconfig-mconf tool.  See nuttx/README.txt
          and misc/tools/

       b. Execute 'make menuconfig' in nuttx/ in order to start the
          reconfiguration process.

    2. By default, this configuration assumes that you are using the
       Cygwin environment on Windows.  An option is to use the native
       CMD.exe window build as described in the top-level README.txt
       file.  To set up that configuration:

       -CONFIG_WINDOWS_CYGWIN=y
       +CONFIG_WINDOWS_NATIVE=y

       And after configuring, make sure that CONFIG_APPS_DIR uses
       the back slash character.  For example:

        CONFIG_APPS_DIR="..\apps"

      NOTES:
      
      a. If you need to change the toolchain path used in Make.defs, you
         will need to use the short 8.3 filenames to avoid spaces.  On my
         PC, C:\PROGRA~1\ is is C:\Program Files\ and C:\PROGRA~2\ is
         C:\Program Files (x86)\
      b. You can't use setenv.sh in the native Windows environment.  Try
         scripts/setenv.bat instead.
      c. At present, the native Windows build fails at the final link stages.
         The failure is due to problems in arch/z16/src/nuttx.linkcmd that
         is autogenerated by arch/z16/src/Makefile.  The basic problem
         is the spurious spaces and and carrirage returns are generated at
         the end of the lines after a line continuation (\ ^M).  If these
         trailing bad characters are manually eliminated, then the build
         will succeed on the next try.
      d. Hmmm... when last tested, there some missing .obj files in arch/z16/src.
         A little additional TLC might be needed to get a reliable Windows
         native build.

pashello
--------

    Configures to use examples/pashello for execution from FLASH
    See examples/README.txt for information about pashello.

    NOTES:

    1. This configuration uses the mconf-based configuration tool.  To
       change this configuration using that tool, you should:

       a. Build and install the kconfig-mconf tool.  See nuttx/README.txt
          and misc/tools/

       b. Execute 'make menuconfig' in nuttx/ in order to start the
          reconfiguration process.

    2. The last time I tried building this configuration, there were
       a few undefined symbols from the PCODE logic.  It might require
       a little TLC to get this all working again.

    3. The native windows build has not been tried with this configuration
       but should, in principle, work (see notes for the ostest configuration
       above).

Check out any README.txt files in these <sub-directory>s.