forked from Archive/PX4-Autopilot
776 lines
35 KiB
Plaintext
776 lines
35 KiB
Plaintext
configs/pic32mx7mmb README
|
|
===============================
|
|
|
|
This README file discusses the port of NuttX to the Mikroelektronika PIC32MX7
|
|
Multimedia Board (MMB). See http://www.mikroe.com/ for further information.
|
|
|
|
Contents
|
|
========
|
|
|
|
PIC32MX795F512L Pin Out
|
|
Toolchains
|
|
Creating Compatible NuttX HEX files
|
|
Serial Console
|
|
LEDs
|
|
PIC32MX Configuration Options
|
|
Configurations
|
|
|
|
PIC32MX795F512L Pin Out
|
|
=======================
|
|
|
|
LEFT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left)
|
|
--- ---------------------------------- -------------------------- -----------------------------------------------
|
|
PIN CONFIGURATIONS SIGNAL NAME ON-BOARD CONNECTIONS
|
|
(Family Data Sheet Table 1-1) (PIC32MX7 Schematic)
|
|
--- ---------------------------------- -------------------------- -----------------------------------------------
|
|
1 RG15/AERXERR AERXERR LAN8720A RXERR
|
|
2 VDD VCC3 ---
|
|
3 PMD5/RE5 PMPD5 TFT display, HDR1 pin 13
|
|
4 PMD6/RE6 PMPD6 TFT display, HDR1 pin 12
|
|
5 PMD7/RE7 PMPD7 TFT display, HDR1 pin 11
|
|
6 RC1/T2CK LCD_RST TFT display
|
|
7 RC2/AC2TX/T3CK EE_CS# M25P80 CS
|
|
8 RC3/AC2RX/T4CK ACL_CS# ADXL345 CS and VCC
|
|
9 RC4/SDI1/T5CK SDI1 SPI1 data IN
|
|
10 PMA5/CN8/ECOL/RG6/SCK2/U3RTS/U6TX SD_WP SD card, write protect
|
|
11 PMA4/CN9/ECRS/RG7/SDA4/SDI2/U3RX SD_CD# SD card, card detect (not)
|
|
12 PMA3/AECRSDV/AERXDV/CN10/ECRSDV/ AECRSDV LAN8720A SRS_DIV
|
|
ERXDV/RG8/SCL4/SDO2/U3TX
|
|
13 MCLR MCLR Debug connector
|
|
14 PMA2/AEREFCLK/AERXCLK/CN11/ AEREFCLK LAN8720A INT
|
|
EREFCLK/ERXCLK/RG9/SS2/U3CTS/
|
|
U6RX
|
|
15 VSS (grounded) ---
|
|
16 VDD VCC3 ---
|
|
17 RA0/TMS LED-0 LED0 (pulled up), HDR2 pin 26
|
|
18 AERXD0/INT1/RE8 AERXD0 LAN8720A RXD0
|
|
19 AERXD1/INT2/RE9 AERXD1 LAN8720A RXD1
|
|
20 AN5/C1IN+/CN7/RB5/VBUSON RB5 HDR1 pin 28
|
|
21 AN4/C1IN-/CN6/RB4 CDC_CS# ?
|
|
22 AN3/C2IN+/CN5/RB3 JOY-D Joystick D, HDR1 pin 21
|
|
23 AN2/C2IN-/CN4/RB2 JOY-C Joystick C, HDR1 pin 22
|
|
24 AN1/CN3/PGEC1/RB1 JOY-B Joystick B, HDR1 pin 23
|
|
25 AN0/CN2/PGED1/RB0 JOY-A Joystick A, HDR1 pin 24
|
|
|
|
BOTTOM SIDE, LEFT-TO-RIGHT (if pin 1 is in upper left)
|
|
--- ---------------------------------- -------------------------- -----------------------------------------------
|
|
PIN CONFIGURATIONS SIGNAL NAME ON-BOARD CONNECTIONS
|
|
(Family Data Sheet Table 1-1) (PIC32MX7 Schematic)
|
|
--- ---------------------------------- -------------------------- -----------------------------------------------
|
|
26 AN6/OCFA/PGEC2/RB6 PGC2 Debugger interface
|
|
27 AN7/PGED2/RB7 PGD2 Debugger interface
|
|
28 PMA7/AERXD2/CVREF-/RA9 SD_CD# SD Connector
|
|
29 PMA6/AERXD3/CVREF+/RA10/VREF+ JOY-CP Joystick CP, HDR1 pin 25
|
|
30 AVDD VCC3 ---
|
|
31 AVSS (grounded) ---
|
|
32 AN8/C1OUT/RB8 TEMP MCP9700A VOUT
|
|
33 AN9/C2OUT/RB9 USB-PSW USB soft-connect pull-up, HDR2 pin 3
|
|
34 PMA13/AN10/RB10/CVREFOUT LCD-YD TFT display
|
|
35 PMA12/AETXERR/AN11/ERXERR/RB11 LCD-XR TFT display
|
|
36 VSS (grounded) ---
|
|
37 VDD P32_VDD ---
|
|
38 RA1/TCK LED-1 LED1 (pulled up), HDR2 pin 27
|
|
39 AC1TX/RF13/SCK4/U2RTS/U5TX SCK3A WM873ASEDS BCLK, HDR2 pin 21
|
|
40 AC1RX/RF12/SS4/U2CTS/U5RX LRC WM873ASEDS DACLRC
|
|
41 PMA11/AECRS/AN12/ERXD0/RB12 LCD-YU TFT display
|
|
42 PMA10/AECOL/AN13/ERXD1/RB13 LCD-XL TFT display
|
|
43 PMA1/AETXD3/AN14/ERXD2/PMALH/RB14 LCD-CS# TFT display, HDR2 pin 3
|
|
44 PMA0/AETXD2/AN15/CN12/ERXD3/OCFB/ LCD-RS TFT display
|
|
PMALL/RB15
|
|
45 VSS (grounded) ---
|
|
46 VDD P32_VDD ---
|
|
47 AETXD0/CN20/RD14/SS3/U1CTS/U4RX AETXD0 LAN8720A TXD0
|
|
48 AETXD1/CN21/RD15/SCK3/U1RTS/U4TX AETXD1 LAN8720A TXD1
|
|
49 PMA9/CN17/RF4/SDA5/SDI4/U2RX SDI3A WM873ASEDS ADCDAT, HDR2 pin 19
|
|
50 PMA8/CN18/RF5/SCL5/SDO4/U2TX SDO3A WM873ASEDS DACDAT, HDR2 pin 20
|
|
|
|
RIGHT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left)
|
|
--- ---------------------------------- -------------------------- -----------------------------------------------
|
|
PIN CONFIGURATIONS SIGNAL NAME ON-BOARD CONNECTIONS
|
|
(Family Data Sheet Table 1-1) (PIC32MX7 Schematic)
|
|
--- ---------------------------------- -------------------------- -----------------------------------------------
|
|
75 VSS (grounded)
|
|
74 CN0/RC14/SOSCO/T1CK SOSC0 32.768kHz Oscillator
|
|
73 CN1/RC13/SOSCI SOSC1 32.768kHz Oscillator
|
|
72 OC1/INT0/RD0/SDO1 SDO1M SPI1 data out
|
|
71 PMA14/AEMDC/EMDC/IC4/PMCS1/RD11 AEMDC LAN8720A MDC
|
|
70 PMA15/IC3/PMCS2/RD10/SCK1 SCK1M SPI1 clock
|
|
69 IC2/RD9/SS1 LED-2 LED2 (pulled up), HDR2 pin 28
|
|
68 AEMDIO/EMDIO/IC1/RD8/RTCC AEMDIO LAN8720A MDIO
|
|
67 AETXEN/INT4/RA15/SDA1 AETXN LAN8720A TXEN
|
|
66 AETXCLK/INT3/RA14/SCL1 RA14 HDR2 pin 14
|
|
65 VSS (grounded) ---
|
|
64 CLKO/OSC2/RC15 8MHz crystal
|
|
63 CLKI/OSC1/RC12 8MHz crystal
|
|
62 VDD VCC3 ---
|
|
61 RA5/TDO RA5 HDR2 pin 13
|
|
60 RA4/TDI RA4 HDR2 pin 12
|
|
59 RA3/SDA2 SDA2 I2C2 SDA, 24AA01 SDA
|
|
58 RA2/SCL2 SCL2 I2C2 SCL, 24AA01 SCL
|
|
57 D+/RG2 USBDP USB device
|
|
56 D-/RG3 USBDM USB device
|
|
55 VUSB VCC3 ---
|
|
54 VBUS USB_DET USB device
|
|
53 RF8/SCL3/SDO3/U1TX U1TX RS-232
|
|
52 RF2/SDA3/SDI3/U1RX U2RX RS-232
|
|
51 RF3/USBID USB-ID USB device
|
|
|
|
TOP SIDE, LEFT-TO-RIGHT (if pin 1 is in upper left)
|
|
--- ---------------------------------- -------------------------- -----------------------------------------------
|
|
PIN CONFIGURATIONS SIGNAL NAME ON-BOARD CONNECTIONS
|
|
(Family Data Sheet Table 1-1) (PIC32MX7 Schematic)
|
|
--- ---------------------------------- -------------------------- -----------------------------------------------
|
|
100 PMD4/RE4 PMPD4 TFT display, HDR1 pin 14
|
|
99 PMD3/RE3 PMPD3 TFT display, HDR1 pin 15
|
|
98 PMD2/RE2 PMPD2 TFT display, HDR1 pin 16
|
|
97 RG13/TRD0 TRD0 HDR2 pin 7
|
|
96 RG12/TRD1 TRD1 HDR2 pin 8
|
|
95 RG14/TRD2 TRD2 HDR2 pin 9
|
|
94 PMD1/RE1 PMPD1 TFT display, HDR1 pin 17
|
|
93 PMD0/RE0 PMPD0 TFT display, HDR1 pin 18
|
|
92 RA7/TRD3 TRD3 HDR2 pin 10
|
|
91 RA6/TRCLK TRCLK HDR2 pin 6
|
|
90 PMD8/C2RX/RG0 PMPD8 TFT display, HDR1 pin 10
|
|
89 PMD9/C2TX/ETXERR/RG1 PMPD9 TFT display, HDR1 pin 9
|
|
88 PMD10/C1TX/ETXD0/RF1 PMPD10 TFT display, HDR1 pin 8
|
|
87 PMD11/C1RX/ETXD1/RF0 PMPD11 TFT display, HDR1 pin 7
|
|
86 VDD P32_VDD ---
|
|
85 VCAP/VCORE (capacitor to ground) ---
|
|
84 PMD15/CN16/ETXCLK/RD7 PMPD15 TFT display, HDR1 pin 3
|
|
83 PMD14/CN15/ETXEN/RD6 PMPD14 TFT display, HDR1 pin 4
|
|
82 CN14/PMRD/RD5 PMPRD
|
|
81 CN13/OC5/PMWR/RD4 PMPWR
|
|
80 PMD13/CN19/ETXD3/RD13 PMPD13 TFT display, HDR1 pin 5
|
|
79 PMD12/ETXD2/IC5/RD12 PMPD12 TFT display, HDR1 pin 6
|
|
78 OC4/RD3 RD3 HDR2 pin 5
|
|
77 OC3/RD2 LCD_BLED LCD backlight LED
|
|
76 OC2/RD1 RD1 HDR2 pin 11
|
|
|
|
Toolchains
|
|
==========
|
|
|
|
I am using the free, LITE version of the PIC32MX toolchain available
|
|
for download from the microchip.com web site. I am using the Windows
|
|
version. The MicroChip toolchain is the only toolchaing currently
|
|
supported in these configurations, but it should be a simple matter to
|
|
adapt to other toolchains by modifying the Make.defs file include in
|
|
each configuration.
|
|
|
|
Toolchain Options:
|
|
|
|
CONFIG_PIC32MX_MICROCHIPW - MicroChip full toolchain for Windows
|
|
CONFIG_PIC32MX_MICROCHIPL - MicroChip full toolchain for Linux
|
|
CONFIG_PIC32MX_MICROCHIPW_LITE - MicroChip LITE toolchain for Windows
|
|
CONFIG_PIC32MX_MICROCHIPL_LITE - MicroChip LITE toolchain for Linux
|
|
|
|
Windows Native Toolchains
|
|
|
|
NOTE: There are several limitations to using a Windows based toolchain in a
|
|
Cygwin environment. The three biggest are:
|
|
|
|
1. The Windows toolchain cannot follow Cygwin paths. Path conversions are
|
|
performed automatically in the Cygwin makefiles using the 'cygpath' utility
|
|
but you might easily find some new path problems. If so, check out 'cygpath -w'
|
|
|
|
2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links
|
|
are used in Nuttx (e.g., include/arch). The make system works around these
|
|
problems for the Windows tools by copying directories instead of linking them.
|
|
But this can also cause some confusion for you: For example, you may edit
|
|
a file in a "linked" directory and find that your changes had no effect.
|
|
That is because you are building the copy of the file in the "fake" symbolic
|
|
directory. If you use a Windows toolchain, you should get in the habit of
|
|
making like this:
|
|
|
|
make clean_context all
|
|
|
|
An alias in your .bashrc file might make that less painful.
|
|
|
|
3. Dependencies are not made when using Windows versions of the GCC. This is
|
|
because the dependencies are generated using Windows pathes which do not
|
|
work with the Cygwin make.
|
|
|
|
Support has been added for making dependencies with the windows-native toolchains.
|
|
That support can be enabled by modifying your Make.defs file as follows:
|
|
|
|
- MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
|
+ MKDEP = $(TOPDIR)/tools/mkdeps.sh --winpaths "$(TOPDIR)"
|
|
|
|
If you have problems with the dependency build (for example, if you are not
|
|
building on C:), then you may need to modify tools/mkdeps.sh
|
|
|
|
Powering the Board
|
|
==================
|
|
|
|
[To be provided]
|
|
|
|
Creating Compatible NuttX HEX files
|
|
===================================
|
|
|
|
Intel Hex Format Files:
|
|
-----------------------
|
|
|
|
When NuttX is built it will produce two files in the top-level NuttX
|
|
directory:
|
|
|
|
1) nuttx - This is an ELF file, and
|
|
2) nuttx.hex - This is an Intel Hex format file. This is controlled by
|
|
the setting CONFIG_INTELHEX_BINARY in the .config file.
|
|
|
|
The PICkit tool wants an Intel Hex format file to burn into FLASH. However,
|
|
there is a problem with the generated nutt.hex: The tool expects the nuttx.hex
|
|
file to contain physical addresses. But the nuttx.hex file generated from the
|
|
top-level make will have address in the KSEG0 and KSEG1 regions.
|
|
|
|
tools/mkpichex:
|
|
---------------
|
|
|
|
There is a simple tool in the configs/pic32mx7mmb/tools directory
|
|
that can be used to solve both issues with the nuttx.hex file. But,
|
|
first, you must build the the tools:
|
|
|
|
cd configs/pic32mx7mmb/tools
|
|
make
|
|
|
|
Now you will have an excecutable file call mkpichex (or mkpichex.exe on
|
|
Cygwin). This program will take the nutt.hex file as an input, it will
|
|
convert all of the KSEG0 and KSEG1 addresses to physical address, and
|
|
it will write the modified file, replacing the original nuttx.hex.
|
|
|
|
To use this file, you need to do the following things:
|
|
|
|
. ./setenv.sh # Source setenv.sh. Among other this, this script
|
|
# will add configs/pic32mx7mmb/tools to your
|
|
# PATH variable
|
|
make # Build nuttx and nuttx.hex
|
|
mkpichex $PWD # Convert addresses in nuttx.hex. $PWD is the path
|
|
# to the top-level build directory. It is the only
|
|
# required input to mkpichex.
|
|
|
|
Serial Console
|
|
==============
|
|
|
|
UART1 is connected to the on-board RS-232 connector
|
|
|
|
LEDs
|
|
====
|
|
|
|
The Mikroelektronika PIC32MX7 MMB has 3 user LEDs labeled LED0-2 in the
|
|
schematics:
|
|
|
|
--- ----- ---------------------------------------------------------
|
|
PIN Board Notes
|
|
--- ----- ---------------------------------------------------------
|
|
RA0 LED0 Pulled-up, low value illuminates
|
|
RA1 LED1 Pulled-up, low value illuminates
|
|
RD9 LED2 Pulled-up, low value illuminates
|
|
RA9 LED4 Not available for general use*, indicates MMC/SD activity
|
|
--- LED5 Not controllable by software, indicates power-on
|
|
|
|
* RA9 is also the SD chip select. It will illuminate whenever the SD card
|
|
is selected. If SD is not used, then LED4 could also be used as a user-
|
|
controlled LED.
|
|
|
|
If CONFIG_ARCH_LEDS is defined, then NuttX will control these LEDs as follows:
|
|
|
|
ON OFF
|
|
------------------------- ---- ---- ---- ---- ---- ----
|
|
LED0 LED1 LED2 LED0 LED1 LED2
|
|
------------------------- ---- ---- ---- ---- ---- ----
|
|
LED_STARTED 0 OFF OFF OFF --- --- ---
|
|
LED_HEAPALLOCATE 1 ON OFF N/C --- --- ---
|
|
LED_IRQSENABLED 2 OFF ON N/C --- --- ---
|
|
LED_STACKCREATED 3 ON ON N/C --- --- ---
|
|
LED_INIRQ 4 N/C N/C ON N/C N/C OFF
|
|
LED_SIGNAL 4 N/C N/C ON N/C N/C OFF
|
|
LED_ASSERTION 4 N/C N/C ON N/C N/C OFF
|
|
LED_PANIC 5 ON N/C N/C OFF N/C N/C
|
|
|
|
PIC32MX Configuration Options
|
|
=============================
|
|
|
|
General Architecture Settings:
|
|
|
|
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
|
|
be set to:
|
|
|
|
CONFIG_ARCH=mips
|
|
|
|
CONFIG_ARCH_family - For use in C code:
|
|
|
|
CONFIG_ARCH_MIPS=y
|
|
|
|
CONFIG_ARCH_architecture - For use in C code:
|
|
|
|
CONFIG_ARCH_MIPS32=y
|
|
|
|
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
|
|
|
CONFIG_ARCH_CHIP=pic32mx
|
|
|
|
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
|
|
chip:
|
|
|
|
CONFIG_ARCH_CHIP_PIC32MX795F512L=y
|
|
|
|
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
|
|
hence, the board that supports the particular chip or SoC.
|
|
|
|
CONFIG_ARCH_BOARD=pic32mx7mmb
|
|
|
|
CONFIG_ARCH_BOARD_name - For use in C code
|
|
|
|
CONFIG_ARCH_BOARD_PIC32MX7MMB=y
|
|
|
|
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
|
|
of delay loops
|
|
|
|
CONFIG_ENDIAN_BIG - define if big endian (default is little
|
|
endian)
|
|
|
|
CONFIG_DRAM_SIZE - Describes the installed DRAM (CPU SRAM in this case):
|
|
|
|
CONFIG_DRAM_SIZE=(32*1024) (32Kb)
|
|
|
|
There is an additional 32Kb of SRAM in AHB SRAM banks 0 and 1.
|
|
|
|
CONFIG_DRAM_START - The start address of installed DRAM
|
|
|
|
CONFIG_DRAM_START=0x10000000
|
|
|
|
CONFIG_DRAM_END - Last address+1 of installed RAM
|
|
|
|
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
|
|
|
|
CONFIG_ARCH_IRQPRIO - The PIC32MXx supports interrupt prioritization
|
|
|
|
CONFIG_ARCH_IRQPRIO=y
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
|
|
have LEDs
|
|
|
|
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
|
stack. If defined, this symbol is the size of the interrupt
|
|
stack in bytes. If not defined, the user task stacks will be
|
|
used during interrupt handling.
|
|
|
|
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
|
|
|
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
|
cause a 100 second delay during boot-up. This 100 second delay
|
|
serves no purpose other than it allows you to calibratre
|
|
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
|
|
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
|
|
the delay actually is 100 seconds.
|
|
|
|
PIC32MX Configuration
|
|
|
|
CONFIG_PIC32MX_MVEC - Select muli- vs. single-vectored interrupts
|
|
|
|
Individual subsystems can be enabled:
|
|
|
|
CONFIG_PIC32MX_WDT - Watchdog timer
|
|
CONFIG_PIC32MX_T2 - Timer 2 (Timer 1 is the system time and always enabled)
|
|
CONFIG_PIC32MX_T3 - Timer 3
|
|
CONFIG_PIC32MX_T4 - Timer 4
|
|
CONFIG_PIC32MX_T5 - Timer 5
|
|
CONFIG_PIC32MX_IC1 - Input Capture 1
|
|
CONFIG_PIC32MX_IC2 - Input Capture 2
|
|
CONFIG_PIC32MX_IC3 - Input Capture 3
|
|
CONFIG_PIC32MX_IC4 - Input Capture 4
|
|
CONFIG_PIC32MX_IC5 - Input Capture 5
|
|
CONFIG_PIC32MX_OC1 - Output Compare 1
|
|
CONFIG_PIC32MX_OC2 - Output Compare 2
|
|
CONFIG_PIC32MX_OC3 - Output Compare 3
|
|
CONFIG_PIC32MX_OC4 - Output Compare 4
|
|
CONFIG_PIC32MX_OC5 - Output Compare 5
|
|
CONFIG_PIC32MX_I2C1 - I2C 1
|
|
CONFIG_PIC32MX_I2C2 - I2C 2
|
|
CONFIG_PIC32MX_I2C3 - I2C 3
|
|
CONFIG_PIC32MX_I2C4 - I2C 4
|
|
CONFIG_PIC32MX_I2C5 - I2C 5
|
|
CONFIG_PIC32MX_SPI1 - SPI 1
|
|
CONFIG_PIC32MX_SPI2 - SPI 2
|
|
CONFIG_PIC32MX_SPI3 - SPI 3
|
|
CONFIG_PIC32MX_SPI4 - SPI 4
|
|
CONFIG_PIC32MX_UART1 - UART 1
|
|
CONFIG_PIC32MX_UART2 - UART 2
|
|
CONFIG_PIC32MX_UART3 - UART 3
|
|
CONFIG_PIC32MX_UART4 - UART 4
|
|
CONFIG_PIC32MX_UART5 - UART 5
|
|
CONFIG_PIC32MX_UART6 - UART 6
|
|
CONFIG_PIC32MX_ADC - ADC 1
|
|
CONFIG_PIC32MX_PMP - Parallel Master Port
|
|
CONFIG_PIC32MX_CM1 - Comparator 1
|
|
CONFIG_PIC32MX_CM2 - Comparator 2
|
|
CONFIG_PIC32MX_RTCC - Real-Time Clock and Calendar
|
|
CONFIG_PIC32MX_DMA - DMA
|
|
CONFIG_PIC32MX_FLASH - FLASH
|
|
CONFIG_PIC32MX_USBDEV - USB device
|
|
CONFIG_PIC32MX_USBHOST - USB host
|
|
CONFIG_PIC32MX_CAN1 - Controller area network 1
|
|
CONFIG_PIC32MX_CAN2 - Controller area network 2
|
|
CONFIG_PIC32MX_ETHERNET - Ethernet
|
|
|
|
PIC32MX Configuration Settings
|
|
DEVCFG0:
|
|
CONFIG_PIC32MX_DEBUGGER - Background Debugger Enable. Default 3 (disabled). The
|
|
value 2 enables.
|
|
CONFIG_PIC32MX_ICESEL - In-Circuit Emulator/Debugger Communication Channel Select
|
|
Default 1 (PG2)
|
|
CONFIG_PIC32MX_PROGFLASHWP - Program FLASH write protect. Default 0xff (disabled)
|
|
CONFIG_PIC32MX_BOOTFLASHWP - Default 1 (disabled)
|
|
CONFIG_PIC32MX_CODEWP - Default 1 (disabled)
|
|
DEVCFG1: (All settings determined by selections in board.h)
|
|
DEVCFG2: (All settings determined by selections in board.h)
|
|
DEVCFG3:
|
|
CONFIG_PIC32MX_USBIDO - USB USBID Selection. Default 1 if USB enabled
|
|
(USBID pin is controlled by the USB module), but 0 (GPIO) otherwise.
|
|
CONFIG_PIC32MX_VBUSIO - USB VBUSON Selection (Default 1 if USB enabled
|
|
(VBUSON pin is controlled by the USB module, but 0 (GPIO) otherwise.
|
|
CONFIG_PIC32MX_WDENABLE - Enabled watchdog on power up. Default 0 (watchdog
|
|
can be enabled later by software).
|
|
|
|
The priority of interrupts may be specified. The value ranage of
|
|
priority is 4-31. The default (16) will be used if these any of these
|
|
are undefined.
|
|
|
|
CONFIG_PIC32MX_CTPRIO - Core Timer Interrupt
|
|
CONFIG_PIC32MX_CS0PRIO - Core Software Interrupt 0
|
|
CONFIG_PIC32MX_CS1PRIO - Core Software Interrupt 1
|
|
CONFIG_PIC32MX_INT0PRIO - External Interrupt 0
|
|
CONFIG_PIC32MX_INT1PRIO - External Interrupt 1
|
|
CONFIG_PIC32MX_INT2PRIO - External Interrupt 2
|
|
CONFIG_PIC32MX_INT3PRIO - External Interrupt 3
|
|
CONFIG_PIC32MX_INT4PRIO - External Interrupt 4
|
|
CONFIG_PIC32MX_FSCMPRIO - Fail-Safe Clock Monitor
|
|
CONFIG_PIC32MX_T1PRIO - Timer 1 (System timer) priority
|
|
CONFIG_PIC32MX_T2PRIO - Timer 2 priority
|
|
CONFIG_PIC32MX_T3PRIO - Timer 3 priority
|
|
CONFIG_PIC32MX_T4PRIO - Timer 4 priority
|
|
CONFIG_PIC32MX_T5PRIO - Timer 5 priority
|
|
CONFIG_PIC32MX_IC1PRIO - Input Capture 1
|
|
CONFIG_PIC32MX_IC2PRIO - Input Capture 2
|
|
CONFIG_PIC32MX_IC3PRIO - Input Capture 3
|
|
CONFIG_PIC32MX_IC4PRIO - Input Capture 4
|
|
CONFIG_PIC32MX_IC5PRIO - Input Capture 5
|
|
CONFIG_PIC32MX_OC1PRIO - Output Compare 1
|
|
CONFIG_PIC32MX_OC2PRIO - Output Compare 2
|
|
CONFIG_PIC32MX_OC3PRIO - Output Compare 3
|
|
CONFIG_PIC32MX_OC4PRIO - Output Compare 4
|
|
CONFIG_PIC32MX_OC5PRIO - Output Compare 5
|
|
CONFIG_PIC32MX_I2C1PRIO - I2C 1
|
|
CONFIG_PIC32MX_I2C2PRIO - I2C 2
|
|
CONFIG_PIC32MX_I2C3PRIO - I2C 3
|
|
CONFIG_PIC32MX_I2C4PRIO - I2C 4
|
|
CONFIG_PIC32MX_I2C5PRIO - I2C 5
|
|
CONFIG_PIC32MX_SPI2PRIO - SPI 2
|
|
CONFIG_PIC32MX_UART1PRIO - UART 1
|
|
CONFIG_PIC32MX_UART2PRIO - UART 2
|
|
CONFIG_PIC32MX_CN - Input Change Interrupt
|
|
CONFIG_PIC32MX_ADCPRIO - ADC1 Convert Done
|
|
CONFIG_PIC32MX_PMPPRIO - Parallel Master Port
|
|
CONFIG_PIC32MX_CM1PRIO - Comparator 1
|
|
CONFIG_PIC32MX_CM2PRIO - Comparator 2
|
|
CONFIG_PIC32MX_FSCMPRIO - Fail-Safe Clock Monitor
|
|
CONFIG_PIC32MX_RTCCPRIO - Real-Time Clock and Calendar
|
|
CONFIG_PIC32MX_DMA0PRIO - DMA Channel 0
|
|
CONFIG_PIC32MX_DMA1PRIO - DMA Channel 1
|
|
CONFIG_PIC32MX_DMA2PRIO - DMA Channel 2
|
|
CONFIG_PIC32MX_DMA3PRIO - DMA Channel 3
|
|
CONFIG_PIC32MX_DMA4PRIO - DMA Channel 4
|
|
CONFIG_PIC32MX_DMA5PRIO - DMA Channel 5
|
|
CONFIG_PIC32MX_DMA6PRIO - DMA Channel 6
|
|
CONFIG_PIC32MX_DMA7PRIO - DMA Channel 7
|
|
CONFIG_PIC32MX_FCEPRIO - Flash Control Event
|
|
CONFIG_PIC32MX_USBPRIO - USB
|
|
|
|
PIC32MXx specific device driver settings. NOTE: For the Ethernet
|
|
starter kit, there is no RS-232 connector (even with the MEB). See
|
|
discussion above ("") for information about how you can configure
|
|
an external MAX2232 board to get a serial console.
|
|
|
|
CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
|
console and ttys0 (default is the UART0).
|
|
CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
|
This specific the size of the receive buffer
|
|
CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
|
being sent. This specific the size of the transmit buffer
|
|
CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
|
|
CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
|
CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
|
CONFIG_UARTn_2STOP - Two stop bits
|
|
|
|
PIC32MX specific PHY/Ethernet device driver settings
|
|
|
|
CONFIG_PHY_KS8721 - Selects the Micrel KS8721 PHY
|
|
CONFIG_PHY_DP83848C - Selects the National Semiconduction DP83848C PHY
|
|
CONFIG_PHY_LAN8720 - Selects the SMSC LAN8720 PHY
|
|
CONFIG_PHY_AUTONEG - Enable auto-negotion
|
|
CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed.
|
|
CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex
|
|
CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 2
|
|
CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 4
|
|
CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is
|
|
the higest priority.
|
|
CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented).
|
|
CONFIG_NET_DUMPPACKET - Dump all received and transmitted packets.
|
|
Also needs CONFIG_DEBUG.
|
|
CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs
|
|
CONFIG_DEBUG.
|
|
CONFIG_NET_HASH - Enable receipt of near-perfect match frames.
|
|
CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames.
|
|
Automatically set if CONFIG_NET_IGMP is selected.
|
|
|
|
Related DEVCFG3 Configuration Settings:
|
|
CONFIG_PIC32MX_FETHIO: Ethernet I/O Pin Selection bit:
|
|
1 = Default Ethernet I/O Pins
|
|
0 = Alternate Ethernet I/O Pins
|
|
CONFIG_PIC32MX_FMIIEN: Ethernet MII Enable bit
|
|
1 = MII enabled
|
|
0 = RMII enabled
|
|
|
|
PIC32MXx USB Device Configuration
|
|
|
|
PIC32MXx USB Host Configuration (the PIC32MX does not support USB Host)
|
|
|
|
Configurations
|
|
==============
|
|
|
|
Each PIC32MX configuration is maintained in a sudirectory and can be
|
|
selected as follow:
|
|
|
|
cd tools
|
|
./configure.sh pic32mx7mmb/<subdir>
|
|
cd -
|
|
. ./setenv.sh
|
|
|
|
Where <subdir> is one of the following:
|
|
|
|
ostest:
|
|
=======
|
|
Description.
|
|
------------
|
|
This configuration directory, performs a simple OS test using
|
|
apps/examples/ostest.
|
|
|
|
Serial Output.
|
|
--------------
|
|
The OS test produces all of its test output on the serial console.
|
|
This configuration has UART1 enabled as a serial console.
|
|
|
|
nsh:
|
|
====
|
|
Description.
|
|
------------
|
|
This is the NuttShell (NSH) using the NSH startup logic at
|
|
apps/examples/nsh.
|
|
|
|
Serial Output.
|
|
--------------
|
|
The OS test produces all of its test output on the serial console.
|
|
This configuration has UART1 enabled as a serial console.
|
|
|
|
SD Card Support
|
|
---------------
|
|
SD card support is built into this example by default:
|
|
|
|
CONFIG_PIC32MX_SPI1=y
|
|
CONFIG_NSH_ARCHINIT=y
|
|
|
|
The SD card can be mounted from the NSH command line as follows:
|
|
|
|
nsh> mount -t vfat /dev/mmcsd0 /mnt/sdcard
|
|
nsh> ls -l /mnt/sdcard
|
|
/mnt/sdcard:
|
|
-rw-rw-rw- 16 ATEST.TXT
|
|
-rw-rw-rw- 21170 TODO
|
|
-rw-rw-rw- 22 ANOTHER.TXT
|
|
-rw-rw-rw- 22 HI2148.TXT
|
|
-rw-rw-rw- 16 HiFromNotePad.txt
|
|
|
|
USB Configurations.
|
|
------------------
|
|
USB device support is enabled by default in this configuration.
|
|
The following settings are defined by default (and can be set
|
|
to 'n' to disabled USB device support).
|
|
|
|
CONFIG_USBDEV=y : Enable basic USB device support
|
|
CONFIG_PIC32MX_USBDEV=y : Enable PIC32 USB device support
|
|
CONFIG_USBMSC=y : USB supports a mass storage device.
|
|
|
|
In this configuration, NSH will support the following commands:
|
|
|
|
msconn : Connect the mass storage device, exportint the SD
|
|
card as the USB mass storage logical unit.
|
|
msdis : Disconnect the USB mass storage device
|
|
|
|
NOTE: The SD card should *not* be mounted under NSH *and* exported
|
|
by the mass storage device!!! That can result in corruption of the
|
|
SD card format. This is the sequence of commands that you should
|
|
used to work the the SD card safely:
|
|
|
|
mount -t vfat /dev/mmcsd0 /mnt/sdcard : Mount the SD card initially
|
|
...
|
|
umount /mnt/sdcard : Unmount the SD card before connecting
|
|
msconn : Connect the USB MSC
|
|
...
|
|
msdis : Disconnect the USB MSC
|
|
mount -t vfat /dev/mmcsd0 /mnt/sdcard : Re-mount the SD card
|
|
...
|
|
|
|
Other USB other device configurations can be enabled and
|
|
included as NSH built-in built in functions.
|
|
|
|
examples/usbterm - This option can be enabled by uncommenting
|
|
the following line in the appconfig file:
|
|
|
|
CONFIGURED_APPS += examples/usbterm
|
|
|
|
And by enabling one of the USB serial devices:
|
|
|
|
CONFIG_USBMSC=n : Disable USB mass storage device.
|
|
CONFIG_PL2303=y : Enable the Prolifics PL2303 emulation
|
|
CONFIG_CDCACM=y : or the CDC/ACM serial driver (not both)
|
|
|
|
examples/cdcacm - The examples/cdcacm program can be included as an
|
|
function by uncommenting the following line in the appconfig file:
|
|
|
|
CONFIGURED_APPS += examples/cdcacm
|
|
|
|
and defining the following in your .config file:
|
|
|
|
CONFIG_USBMSC=n : Disable USB mass storage device.
|
|
CONFIG_CDCACM=y : Enable the CDCACM device
|
|
|
|
Networking Configurations.
|
|
--------------------------
|
|
Networking is enabled by default in this configuration:
|
|
|
|
CONFIG_NET=y : Enable networking support
|
|
CONFIG_PIC32MX_ETHERNET=y : Enable the PIC32 Ethernet driver
|
|
CONFIG_NSH_TELNET=y : Enable the Telnet NSH console (optional)
|
|
|
|
The default configuration has:
|
|
|
|
CONFIG_NSH_DHCPC=n : DHCP is disabled
|
|
CONFIG_NSH_IPADDR=(10<<24|0<<16|0<<8|2) : Target IP address 10.0.0.2
|
|
CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1) : Host IP address 10.0.0.1
|
|
|
|
This will probably need to be customized for your network.
|
|
|
|
NOTES:
|
|
1. This logic will assume that a network is connected. During its
|
|
initialization, it will try to negotiate the link speed. If you have
|
|
no network connected when you reset the board, there will be a long
|
|
delay (maybe 30 seconds?) before anything happens. That is the timeout
|
|
before the networking finally gives up and decides that no network is
|
|
available.
|
|
|
|
2. This example can support an FTP client. In order to build in FTP client
|
|
support simply uncomment the following lines in the appconfig file (before
|
|
configuring) or in the apps/.config file (after configuring):
|
|
|
|
#CONFIGURED_APPS += netutils/ftpc
|
|
#CONFIGURED_APPS += examples/ftpc
|
|
|
|
3. This example can support an FTP server. In order to build in FTP server
|
|
support simply uncomment the following lines in the appconfig file (before
|
|
configuring) or in the apps/.config file (after configuring):
|
|
|
|
#CONFIGURED_APPS += netutils/ftpd
|
|
#CONFIGURED_APPS += examples/ftpd
|
|
|
|
And enable poll() support in the NuttX configuration file:
|
|
|
|
CONFIG_DISABLE_POLL=n
|
|
|
|
Using a RAM disk and the USB MSC device to the nsh configuration
|
|
----------------------------------------------------------------
|
|
Here is an experimental change to examples/nsh that will create a RAM
|
|
disk and attempt to export that RAM disk as a USB mass storage device.
|
|
|
|
1. Changes to nuttx/.config
|
|
|
|
a) Enable support for the PIC32 USB device
|
|
|
|
-CONFIG_PIC32MX_USBDEV=n
|
|
+CONFIG_PIC32MX_USBDEV=y
|
|
|
|
b) Enable NuttX USB device support
|
|
|
|
-CONFIG_USBDEV=n
|
|
+CONFIG_USBDEV=y
|
|
|
|
c) Enable the USB MSC class driver
|
|
|
|
-CONFIG_USBMSC=n
|
|
+CONFIG_USBMSC=y
|
|
|
|
d) Use a RAM disk (instead of an SD card) as the USB MSC logical unit:
|
|
|
|
-CONFIG_EXAMPLES_USBMSC_DEVPATH1="/dev/mmcsd0"
|
|
+CONFIG_EXAMPLES_USBMSC_DEVPATH1="/dev/ram0"
|
|
|
|
2. Changes to nuttx/.config.
|
|
|
|
a) Enable building of the examples/usbstorage:
|
|
|
|
-# CONFIGURED_APPS += examples/usbstorage
|
|
+ CONFIGURED_APPS += examples/usbstorage
|
|
|
|
3. When NSH first comes up, you must manually create the RAM disk
|
|
before exporting it:
|
|
|
|
a) Create a 64Kb RAM disk at /dev/ram0:
|
|
|
|
nsh> mkrd -s 512 128
|
|
|
|
b) Put a FAT file system on the RAM disk:
|
|
|
|
nsh> mkfatfs /dev/ram0
|
|
|
|
b) Now the 'msconn' command will connect to the host and
|
|
export /dev/ram0 as the USB logical unit:
|
|
|
|
nsh> msconn
|
|
|
|
NOTE: This modification should be considered experimental. IN the
|
|
little testing I have done with it, it appears functional. But the
|
|
logic has not been stressed and there could still be lurking issues.
|
|
(There is a bug associated with this configuration listed in the
|
|
top-level TODO list).
|
|
|
|
Adding LCD and graphics support to the nsh configuration:
|
|
--------------------------------------------------------
|
|
|
|
LCD support is already enabled in defconfig (nuttx/.config):
|
|
|
|
CONFIG_NX=y : Enable graphics suppport
|
|
CONFIG_PIC32MX_PMP=y : Enable parallel port support
|
|
CONFIG_LCD_MIO283QT2=y : MIO283QT2 LCD support
|
|
|
|
But you will have to enable a specific graphics example application
|
|
in order to see anything.
|
|
|
|
appconfig (apps/.config): Enable the application configurations that you
|
|
want to use. Asexamples:
|
|
|
|
CONFIGURED_APPS += examples/nx : Pick one or more
|
|
CONFIGURED_APPS += examples/nxhello :
|
|
CONFIGURED_APPS += examples/nximage :
|
|
CONFIGURED_APPS += examples/nxlines :
|
|
|
|
Enabling touch screen support in the nsh configuaration
|
|
-------------------------------------------------------
|
|
|
|
In defconfig (or nuttx/.config), set:
|
|
|
|
CONFIG_INPUT=y : Enable input device support
|
|
CONFIG_SCHED_WORKQUEUE=y : Work queue support needed
|
|
|
|
In appconfig (or apps/.config), uncomment:
|
|
|
|
CONFIGURED_APPS += examples/touchscreen
|