forked from Archive/PX4-Autopilot
378 lines
15 KiB
Plaintext
378 lines
15 KiB
Plaintext
README
|
|
^^^^^^
|
|
|
|
README file for the Microment Eagle100 NuttX port.
|
|
|
|
References:
|
|
^^^^^^^^^^
|
|
|
|
Micromint: http://www.micromint.com/
|
|
Luminary: http://www.luminarymicro.com/
|
|
|
|
Development Environment
|
|
^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
Either Linux or Cygwin on Windows can be used for the development environment.
|
|
The source has been built only using the GNU toolchain (see below). Other
|
|
toolchains will likely cause problems. Testing was performed using the Cygwin
|
|
environment because the Luminary FLASH programming application was used for
|
|
writing to FLASH and this application works only under Windows.
|
|
|
|
GNU Toolchain Options
|
|
^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
The NuttX make system has been modified to support the following different
|
|
toolchain options.
|
|
|
|
1. The CodeSourcery GNU toolchain,
|
|
2. The devkitARM GNU toolchain, or
|
|
3. The NuttX buildroot Toolchain (see below).
|
|
|
|
All testing has been conducted using the NuttX buildroot toolchain. However,
|
|
the make system is setup to default to use the devkitARM toolchain. To use
|
|
the CodeSourcery or devkitARM GNU toolchain, you simply need to build the
|
|
system as follows:
|
|
|
|
make # Will build for the devkitARM toolchain
|
|
make CROSSDEV=arm-eabi- # Will build for the devkitARM toolchain
|
|
make CROSSDEV=arm-none-eabi- # Will build for the CodeSourcery toolchain
|
|
make CROSSDEV=arm-elf- # Will build for the NuttX buildroot toolchain
|
|
|
|
Of course, hard coding this CROSS_COMPILE value in Make.defs file will save
|
|
some repetitive typing.
|
|
|
|
NOTE: the CodeSourcery and devkitARM toolchains are Windows native toolchains.
|
|
The NuttX buildroot toolchain is a Cygwin toolchain. There are several limitations
|
|
to using a Windows based toolchain in a Cygwin environment. The three biggest are:
|
|
|
|
1. The Windows toolchain cannot follow Cygwin paths. Path conversions are
|
|
performed automatically in the Cygwin makefiles using the 'cygpath' utility
|
|
but you might easily find some new path problems. If so, check out 'cygpath -w'
|
|
|
|
2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links
|
|
are used in Nuttx (e.g., include/arch). The make system works around these
|
|
problems for the Windows tools by copying directories instead of linking them.
|
|
But this can also cause some confusion for you: For example, you may edit
|
|
a file in a "linked" directory and find that your changes had no effect.
|
|
That is because you are building the copy of the file in the "fake" symbolic
|
|
directory. If you use a Windows toolchain, you should get in the habit of
|
|
making like this:
|
|
|
|
make clean_context; make CROSSDEV=arm-none-eabi-
|
|
|
|
An alias in your .bashrc file might make that less painful.
|
|
|
|
3. Dependencies are not made when using Windows versions of the GCC. This is
|
|
because the dependencies are generated using Windows pathes which do not
|
|
work with the Cygwin make.
|
|
|
|
Support has been added for making dependencies with the CodeSourcery toolchain.
|
|
That support can be enabled by modifying your Make.defs file as follows:
|
|
|
|
- MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
|
+ MKDEP = $(TOPDIR)/tools/mkdeps.sh --winpaths "$(TOPDIR)"
|
|
|
|
If you have problems with the dependency build (for example, if you are not
|
|
building on C:), then you may need to modify tools/mkdeps.sh
|
|
|
|
NOTE 1: The CodeSourcery toolchain (2009q1) does not work with default optimization
|
|
level of -Os (See Make.defs). It will work with -O0, -O1, or -O2, but not with
|
|
-Os.
|
|
|
|
NOTE 2: The devkitARM toolchain includes a version of MSYS make. Make sure that
|
|
the paths to Cygwin's /bin and /usr/bin directories appear BEFORE the devkitARM
|
|
path or will get the wrong version of make. It has been reported to me that the
|
|
devkitARM will require an lower optimization level of -O1. Currently all of the
|
|
Make.def files have -O2 for devkitARM -- if you are using this toolchain, you may
|
|
need to review these settings.
|
|
|
|
CodeSourcery on Linux
|
|
^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
If you select the CodeSourcery toolchain, the make system will assume that you
|
|
are running a Windows version of the toolchain. If you are running under Linux,
|
|
the the make will probably fail. The fix is to edit your Make.defs file and
|
|
use something like:
|
|
|
|
CROSSDEV = arm-none-eabi-
|
|
WINTOOL = n
|
|
MKDEP = $(TOPDIR)/tools/mkdeps.sh
|
|
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
|
ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
|
|
ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
|
|
ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/ostest/ld.script
|
|
MAXOPTIMIZATION = -O2
|
|
|
|
The values for TOPDIR is provided by the make system; the value for CONFIG_ARCH_BOARD
|
|
is provided in your defconfig file. 'ostest' refers to the ostest/ configuration;
|
|
this would be different for other configurations.
|
|
|
|
For an example of a CodeSourcery-under-Linux Make.defs file, see
|
|
configs/stm3210e-eval/nsh/Make.defs.
|
|
|
|
NuttX buildroot Toolchain
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
A GNU GCC-based toolchain is assumed. The files */setenv.sh should
|
|
be modified to point to the correct path to the Cortex-M3 GCC toolchain (if
|
|
different from the default in your PATH variable).
|
|
|
|
If you have no Cortex-M3 toolchain, one can be downloaded from the NuttX
|
|
SourceForge download site (https://sourceforge.net/project/showfiles.php?group_id=189573).
|
|
This GNU toolchain builds and executes in the Linux or Cygwin environment.
|
|
|
|
1. You must have already configured Nuttx in <some-dir>/nuttx.
|
|
|
|
cd tools
|
|
./configure.sh eagle100/<sub-dir>
|
|
|
|
2. Download the latest buildroot package into <some-dir>
|
|
|
|
3. unpack the buildroot tarball. The resulting directory may
|
|
have versioning information on it like buildroot-x.y.z. If so,
|
|
rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.
|
|
|
|
4. cd <some-dir>/buildroot
|
|
|
|
5. cp configs/cortexm3-defconfig-4.3.3 .config
|
|
|
|
6. make oldconfig
|
|
|
|
7. make
|
|
|
|
8. Edit setenv.h, if necessary, so that the PATH variable includes
|
|
the path to the newly built binaries.
|
|
|
|
See the file configs/README.txt in the buildroot source tree. That has more
|
|
detailed PLUS some special instructions that you will need to follow if you are
|
|
building a Cortex-M3 toolchain for Cygwin under Windows.
|
|
|
|
Ethernet-Bootloader
|
|
^^^^^^^^^^^^^^^^^^^
|
|
|
|
Here are some notes about using the Luminary Ethernet boot-loader built
|
|
into the Eagle-100 board.
|
|
|
|
Built-In Application:
|
|
|
|
- The board has no fixed IP address but uses DHCP to get an address.
|
|
I used a D-link router; I can use a web browser to surf to the D-link
|
|
web page to get the address assigned by
|
|
|
|
- Then you can use this IP address in your browser to surf to the Eagle-100
|
|
board. It presents several interesting pages -- the most important is
|
|
the page called "Firmware Update". That page includes instructions on
|
|
how to download code to the Eagle-100.
|
|
|
|
- After you burn the first program, you lose this application. Then you
|
|
will probably be better off connected directly to the Eagle-100 board
|
|
or through a switch (The router caused problems for me during downloads).
|
|
|
|
Using the Ethernet Bootloader:
|
|
|
|
- You will need the "LM Flash Programmer application". You can get that
|
|
program from the Luminary web site. There is a link on the LM3S6918 page.
|
|
|
|
- Is there any documentation for using the bootloader? Yes and No: There
|
|
is an application note covering the bootloader on the Luminary site, but
|
|
it is not very informative. The Eagle100 User's Manual has the best
|
|
information.
|
|
|
|
- Are there any special things I have to do in my code, other than setting
|
|
the origin to 0x0000:2000 (APP_START_ADDRESS)? No. The bootloader assumes
|
|
that you have a vector table at that address . The bootloader does the
|
|
following each time it boots (after you have downloaded the first valid
|
|
application):
|
|
|
|
o The bootloader sets the vector table register to the APP_START_ADDRESS,
|
|
o It sets the stack pointer to the address at APP_START_ADDRESS, and then
|
|
o Jumps to the address at APP_START_ADDRESS+4.
|
|
|
|
- You can force the bootloader to skip starting the application and stay
|
|
in the update mode. You will need to do this in order to download a new
|
|
application. You force the update mode by holding the user button on the
|
|
Eagle-100 board while resetting the board. The user button is GPIOA, pin 6
|
|
(call FORCED_UPDATE_PIN in the bootloader code).
|
|
|
|
- Note 1: I had to remove my D-Link router from the configuration in order
|
|
to use the LM Flash Programmer (the Bootloader issues BOOTP requests to
|
|
communicate with the LM Flash Programmer, my router was responding to
|
|
these BOOTP requests and hosing the download). It is safer to connect
|
|
via a switch or via an Ethernet switch.
|
|
|
|
- Note 2: You don't need the router's DHCPD server in the download
|
|
configuration; the Luminary Flash Programmer has the capability of
|
|
temporarily assigning the IP address to the Eagle-100 via BOOTP.
|
|
|
|
Eagle100-specific Configuration Options
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
|
|
be set to:
|
|
|
|
CONFIG_ARCH=arm
|
|
|
|
CONFIG_ARCH_family - For use in C code:
|
|
|
|
CONFIG_ARCH_ARM=y
|
|
|
|
CONFIG_ARCH_architecture - For use in C code:
|
|
|
|
CONFIG_ARCH_CORTEXM3=y
|
|
|
|
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
|
|
|
CONFIG_ARCH_CHIP=lm3s
|
|
|
|
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
|
|
chip:
|
|
|
|
CONFIG_ARCH_CHIP_LM3S6918
|
|
|
|
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
|
|
hence, the board that supports the particular chip or SoC.
|
|
|
|
CONFIG_ARCH_BOARD=eagle100 (for the MicroMint Eagle-100 development board)
|
|
|
|
CONFIG_ARCH_BOARD_name - For use in C code
|
|
|
|
CONFIG_ARCH_BOARD_EAGLE100
|
|
|
|
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
|
|
of delay loops
|
|
|
|
CONFIG_ENDIAN_BIG - define if big endian (default is little
|
|
endian)
|
|
|
|
CONFIG_DRAM_SIZE - Describes the installed DRAM (SRAM in this case):
|
|
|
|
CONFIG_DRAM_SIZE=0x00010000 (64Kb)
|
|
|
|
CONFIG_DRAM_START - The start address of installed DRAM
|
|
|
|
CONFIG_DRAM_START=0x20000000
|
|
|
|
CONFIG_DRAM_END - Last address+1 of installed RAM
|
|
|
|
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
|
|
|
|
CONFIG_ARCH_IRQPRIO - The LM3S6918 supports interrupt prioritization
|
|
|
|
CONFIG_ARCH_IRQPRIO=y
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
|
|
have LEDs
|
|
|
|
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
|
stack. If defined, this symbol is the size of the interrupt
|
|
stack in bytes. If not defined, the user task stacks will be
|
|
used during interrupt handling.
|
|
|
|
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
|
|
|
CONFIG_ARCH_BOOTLOADER - Configure to use the MicroMint Eagle-100
|
|
Ethernet bootloader.
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
|
|
|
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
|
cause a 100 second delay during boot-up. This 100 second delay
|
|
serves no purpose other than it allows you to calibratre
|
|
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
|
|
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
|
|
the delay actually is 100 seconds.
|
|
|
|
There are configurations for disabling support for interrupts GPIO ports.
|
|
GPIOH and GPIOJ must be disabled because they do not exist on the LM3S6918.
|
|
Additional interrupt support can be disabled if desired to reduce memory
|
|
footprint.
|
|
|
|
CONFIG_LM3S_DISABLE_GPIOA_IRQS=n
|
|
CONFIG_LM3S_DISABLE_GPIOB_IRQS=n
|
|
CONFIG_LM3S_DISABLE_GPIOC_IRQS=n
|
|
CONFIG_LM3S_DISABLE_GPIOD_IRQS=n
|
|
CONFIG_LM3S_DISABLE_GPIOE_IRQS=n
|
|
CONFIG_LM3S_DISABLE_GPIOF_IRQS=n
|
|
CONFIG_LM3S_DISABLE_GPIOG_IRQS=n
|
|
CONFIG_LM3S_DISABLE_GPIOH_IRQS=y
|
|
CONFIG_LM3S_DISABLE_GPIOJ_IRQS=y
|
|
|
|
LM3S6818 specific device driver settings
|
|
|
|
CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
|
console and ttys0 (default is the UART0).
|
|
CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
|
This specific the size of the receive buffer
|
|
CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
|
being sent. This specific the size of the transmit buffer
|
|
CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
|
|
CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
|
CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
|
CONFIG_UARTn_2STOP - Two stop bits
|
|
|
|
CONFIG_SSI0_DISABLE - Select to disable support for SSI0
|
|
CONFIG_SSI1_DISABLE - Select to disable support for SSI1
|
|
CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support.
|
|
Poll-waiting is recommended if the interrupt rate would be to
|
|
high in the interrupt driven case.
|
|
CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
|
|
emptying the Rx FIFO. If the SPI frequency is high and this
|
|
value is large, then larger values of this setting may cause
|
|
Rx FIFO overrun errors. Default: half of the Tx FIFO size (4).
|
|
|
|
CONFIG_LM3S_ETHERNET - This must be set (along with CONFIG_NET)
|
|
to build the LM3S Ethernet driver
|
|
CONFIG_LM3S_ETHLEDS - Enable to use Ethernet LEDs on the board.
|
|
CONFIG_LM3S_BOARDMAC - If the board-specific logic can provide
|
|
a MAC address (via lm3s_ethernetmac()), then this should be selected.
|
|
CONFIG_LM3S_ETHHDUPLEX - Set to force half duplex operation
|
|
CONFIG_LM3S_ETHNOAUTOCRC - Set to suppress auto-CRC generation
|
|
CONFIG_LM3S_ETHNOPAD - Set to suppress Tx padding
|
|
CONFIG_LM3S_MULTICAST - Set to enable multicast frames
|
|
CONFIG_LM3S_PROMISCUOUS - Set to enable promiscuous mode
|
|
CONFIG_LM3S_BADCRC - Set to enable bad CRC rejection.
|
|
CONFIG_LM3S_DUMPPACKET - Dump each packet received/sent to the console.
|
|
|
|
Configurations
|
|
^^^^^^^^^^^^^^
|
|
|
|
Each Eagle-100 configuration is maintained in a sudirectory and
|
|
can be selected as follow:
|
|
|
|
cd tools
|
|
./configure.sh eagle100/<subdir>
|
|
cd -
|
|
. ./setenv.sh
|
|
|
|
Where <subdir> is one of the following:
|
|
|
|
nettest:
|
|
This configuration directory may be used to enable networking using the
|
|
LM3S6918's Ethernet controller. It uses examples/nettest to excercise the
|
|
TCP/IP network.
|
|
|
|
httpd:
|
|
This builds the uIP web server example using the examples/uip application
|
|
(for execution from FLASH). See examples/README.txt for information
|
|
about ostest.
|
|
|
|
nsh:
|
|
Configures the NuttShell (nsh) located at examples/nsh. The
|
|
Configuration enables only the serial NSH interfaces (the telnet
|
|
interface should also be functional, but is not enabled in this
|
|
configuration).
|
|
|
|
ostest:
|
|
This configuration directory, performs a simple OS test using
|
|
examples/ostest.
|
|
|
|
thttpd:
|
|
This builds the THTTPD web server example using the THTTPD and
|
|
the examples/thttpd application.
|
|
|
|
By default, all of these examples are built to be used with the Luminary
|
|
Ethernet Bootloader (you can change the ld.script file in any of these
|
|
sub-directories to change that configuration).
|
|
|
|
|