px4-firmware/nuttx/configs/vsn/include/board.h

244 lines
8.4 KiB
C

/************************************************************************************
* configs/vsn/include/board.h
* include/arch/board/board.h
*
* Copyright (C) 2009 Gregory Nutt. All rights reserved.
* Copyright (C) 2011 Uros Platise. All rights reserved
*
* Authors: Gregory Nutt <gnutt@nuttx.org>
* Uros Platise <uros.platise@isotel.eu>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __ARCH_BOARD_BOARD_H
#define __ARCH_BOARD_BOARD_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
#ifndef __ASSEMBLY__
# include <stdint.h>
#endif
#include "stm32_rcc.h"
#include "stm32_sdio.h"
#include "stm32_internal.h"
#include "muxbus.h"
/************************************************************************************
* Definitions
************************************************************************************/
/* Clocking *************************************************************************/
/* On-board external frequency source is 9MHz (HSE) provided by the CC1101, so it is
* not available on power-up. Instead we are about to run on HSI*9 = 36 MHz, see
* up_sysclock.c for details.
*/
#define STM32_BOARD_XTAL 9000000UL
#define STM32_BOARD_HCLK 36000000UL
/* PLL source is either HSI or HSE
* When HSI: PLL multiplier is 9, out frequency 36 MHz
* When HSE: PLL multiplier is 8: out frequency is 9 MHz x 8 = 72MHz
*/
#define STM32_CFGR_PLLSRC_HSI 0
#define STM32_CFGR_PLLMUL_HSI RCC_CFGR_PLLMUL_CLKx9
#define STM32_CFGR_PLLXTPRE_HSE 0
#define STM32_CFGR_PLLSRC_HSE RCC_CFGR_PLLSRC
#define STM32_CFGR_PLLMUL_HSE RCC_CFGR_PLLMUL_CLKx8
/* Use the PLL and set the SYSCLK source to be the PLL */
#define STM32_SYSCLK_SW RCC_CFGR_SW_PLL
#define STM32_SYSCLK_SWS RCC_CFGR_SWS_PLL
/* AHB clock (HCLK, 36 MHz) is SYSCLK on HSI or SYSCLK/2 on HSE */
#define STM32_RCC_CFGR_HPRE_HSI RCC_CFGR_HPRE_SYSCLK
#define STM32_RCC_CFGR_HPRE_HSE RCC_CFGR_HPRE_SYSCLKd2
#define STM32_HCLK_FREQUENCY STM32_BOARD_HCLK
/* APB2 clock (PCLK2) is HCLK (36MHz) */
#define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLK
#define STM32_PCLK2_FREQUENCY STM32_BOARD_HCLK
/* APB2 timers 1 and 8 will receive PCLK2. */
#define STM32_APB2_TIM1_CLKIN (STM32_PCLK2_FREQUENCY)
#define STM32_APB2_TIM8_CLKIN (STM32_PCLK2_FREQUENCY)
/* APB1 clock (PCLK1) is HCLK (36MHz) */
#define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLK
#define STM32_PCLK1_FREQUENCY STM32_BOARD_HCLK
/* APB1 timers 2-4 will receive PCLK1. */
#define STM32_APB1_TIM2_CLKIN (STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM3_CLKIN (STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM4_CLKIN (STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM5_CLKIN (STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM6_CLKIN (STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM7_CLKIN (STM32_PCLK1_FREQUENCY)
/* Timer 1..8 Frequencies */
#define STM32_TIM27_FREQUENCY (STM32_BOARD_HCLK)
#define STM32_TIM18_FREQUENCY (STM32_BOARD_HCLK)
/* USB divider -- Divide PLL clock by 1.5 */
#define STM32_CFGR_USBPRE 0
/* SDIO dividers. Note that slower clocking is required when DMA is disabled
* in order to avoid RX overrun/TX underrun errors due to delayed responses
* to service FIFOs in interrupt driven mode.
*
* SDcard default speed has max SDIO_CK freq of 25 MHz (12.5 Mbps)
* After selection of high speed freq may be 50 MHz (25 Mbps)
* Recommended default voltage: 3.3 V
*
* HCLK=36MHz, SDIOCLK=36 MHz, SDIO_CK=HCLK/(88+2)=400 KHz
*/
#define SDIO_INIT_CLKDIV (88 << SDIO_CLKCR_CLKDIV_SHIFT)
/* DMA ON: HCLK=36 MHz, SDIOCLK=36MHz, SDIO_CK=HCLK/(0+2)=18 MHz
* DMA OFF: HCLK=36 MHz, SDIOCLK=36MHz, SDIO_CK=HCLK/(1+2)=12 MHz
*/
#ifdef CONFIG_SDIO_DMA
# define SDIO_MMCXFR_CLKDIV (0 << SDIO_CLKCR_CLKDIV_SHIFT)
#else
# ifndef CONFIG_DEBUG
# define SDIO_MMCXFR_CLKDIV (1 << SDIO_CLKCR_CLKDIV_SHIFT)
# else
# define SDIO_MMCXFR_CLKDIV (10 << SDIO_CLKCR_CLKDIV_SHIFT)
# endif
#endif
/* DMA ON: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(0+2)=18 MHz
* DMA OFF: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(1+2)=12 MHz
* Extra slow down in debug mode to get rid of underruns.
*/
#ifdef CONFIG_SDIO_DMA
# define SDIO_SDXFR_CLKDIV (0 << SDIO_CLKCR_CLKDIV_SHIFT)
#else
# ifndef CONFIG_DEBUG
# define SDIO_SDXFR_CLKDIV (1 << SDIO_CLKCR_CLKDIV_SHIFT)
# else
# define SDIO_SDXFR_CLKDIV (10 << SDIO_CLKCR_CLKDIV_SHIFT)
# endif
#endif
/* LED definitions ******************************************************************/
/* The VSN has one LED that we will encode as: */
#define LED_STARTED 0 /* ... */
#define LED_HEAPALLOCATE 1 /* ... */
#define LED_IRQSENABLED 2 /* ... */
#define LED_STACKCREATED 3 /* ... */
#define LED_INIRQ 4 /* ... */
#define LED_SIGNAL 5 /* ... */
#define LED_ASSERTION 6 /* ... */
#define LED_PANIC 7 /* ... */
#define LED_IDLE 8 /* shows idle state */
/************************************************************************************
* Public Data
************************************************************************************/
#ifndef __ASSEMBLY__
#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C" {
#else
#define EXTERN extern
#endif
/************************************************************************************
* Board Clock Configuration, called immediatelly after boot
************************************************************************************/
/************************************************************************************
* Name: stm32_boardinitialize
*
* Description:
* All STM32 architectures must provide the following entry point. This entry point
* is called early in the intitialization -- after all memory has been configured
* and mapped but before any devices have been initialized.
*
************************************************************************************/
EXTERN void stm32_boardinitialize(void);
/************************************************************************************
* Name: stm32_board_clockconfig
*
* Description:
* Any STM32 board may replace the "standard" board clock configuration logic with
* its own, custom clock cofiguration logic.
*
************************************************************************************/
#ifdef CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG
EXTERN void stm32_board_clockconfig(void);
#endif
/************************************************************************************
* Button support. (TODO: button is not yet supported)
************************************************************************************/
#ifdef CONFIG_ARCH_BUTTONS
EXTERN void up_buttoninit(void);
EXTERN uint8_t up_buttons(void);
#endif
#undef EXTERN
#if defined(__cplusplus)
}
#endif
#endif /* __ASSEMBLY__ */
#endif /* __ARCH_BOARD_BOARD_H */