forked from Archive/PX4-Autopilot
479 lines
17 KiB
Plaintext
479 lines
17 KiB
Plaintext
configs/pic32mx README
|
|
=====================
|
|
|
|
This README file discusses the port of NuttX to the PIC32MX board from
|
|
PCB Logic Design Co. This board features the MicroChip PIC32MX460F512L.
|
|
The board is a very simple -- little more than a carrier for the PIC32
|
|
MCU plus voltage regulation, debug interface, and an OTG connector.
|
|
|
|
Contents
|
|
========
|
|
|
|
PIC32MX460F512L Pin Out
|
|
MAX3232 Connection
|
|
Toolchains
|
|
Loading NuttX with PICkit2
|
|
PIC32MX Configuration Options
|
|
Configurations
|
|
|
|
PIC32MX460F512L Pin Out
|
|
=======================
|
|
|
|
PIC32MX460F512L 100-Pin TQFP (USB) Pin Out. The mapping to the pins on
|
|
the PCL Logic board are very simple, each pin is brought out to a connector
|
|
label with the PIC32MX460F512L pin number.
|
|
|
|
On board logic only manages power, crystal, and USB signals.
|
|
|
|
LEFT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left)
|
|
PIN NAME
|
|
---- ----------------------------
|
|
1 RG15
|
|
2 Vdd
|
|
3 PMD5/RE5
|
|
4 PMD6/RE6
|
|
5 PMD7/RE7
|
|
6 T2CK/RC1
|
|
7 T3CK/RC2
|
|
8 T4CK/RC3
|
|
9 T5CK/SDI1/RC4
|
|
10 SCK2/PMA5/CN8/RG6
|
|
11 SDI2/PMA4/CN9/RG7
|
|
12 SDO2/PMA3/CN10/RG8
|
|
13 MCLR
|
|
14 SS2/PMA2/CN11/RG9
|
|
15 Vss
|
|
16 Vdd
|
|
17 TMS/RA0
|
|
18 INT1/RE8
|
|
19 INT2/RE9
|
|
20 AN5/C1IN+/VBUSON/CN7/RB5
|
|
21 AN4/C1IN-/CN6/RB4
|
|
22 AN3/C2IN+/CN5/RB3
|
|
23 AN2/C2IN-/CN4/RB2
|
|
24 PGEC1/AN1/CN3/RB1
|
|
25 PGED1/AN0/CN2/RB0
|
|
|
|
BOTTOM SIDE, LEFT-TO-RIGHT (if pin 1 is in upper left)
|
|
PIN NAME
|
|
---- ----------------------------
|
|
26 PGEC2/AN6/OCFA/RB6
|
|
27 PGED2/AN7/RB7
|
|
28 VREF-/CVREF-/PMA7/RA9
|
|
29 VREF+/CVREF+/PMA6/RA10
|
|
30 AVdd
|
|
31 AVss
|
|
32 AN8/C1OUT/RB8
|
|
33 AN9/C2OUT/RB9
|
|
34 AN10/CVREFOUT/PMA13/RB10
|
|
35 AN11/PMA12/RB11
|
|
36 Vss
|
|
37 Vdd
|
|
38 TCK/RA1
|
|
39 U2RTS/RF13
|
|
40 U2CTS/RF12
|
|
41 AN12/PMA11/RB12
|
|
42 AN13/PMA10/RB13
|
|
43 AN14/PMALH/PMA1/RB14
|
|
44 AN15/OCFB/PMALL/PMA0/CN12/RB15
|
|
45 Vss
|
|
46 Vdd
|
|
47 U1CTS/CN20/RD14
|
|
48 U1RTS/CN21/RD15
|
|
49 U2RX/PMA9/CN17/RF4
|
|
50 U2TX/PMA8/CN18/RF5
|
|
|
|
RIGHT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left)
|
|
PIN NAME
|
|
---- ----------------------------
|
|
75 Vss
|
|
74 SOSCO/T1CK/CN0/RC14
|
|
73 SOSCI/CN1/RC13
|
|
72 SDO1/OC1/INT0/RD0
|
|
71 IC4/PMCS1/PMA14/RD11
|
|
70 SCK1/IC3/PMCS2/PMA15/RD10
|
|
69 SS1/IC2/RD9
|
|
68 RTCC/IC1/RD8
|
|
67 SDA1/INT4/RA15
|
|
66 SCL1/INT3/RA14
|
|
65 Vss
|
|
64 OSC2/CLKO/RC15
|
|
63 OSC1/CLKI/RC12
|
|
62 Vdd
|
|
61 TDO/RA5
|
|
60 TDI/RA4
|
|
59 SDA2/RA3
|
|
58 SCL2/RA2
|
|
57 D+/RG2
|
|
56 D-/RG3
|
|
55 VUSB
|
|
54 VBUS
|
|
53 U1TX/RF8
|
|
52 U1RX/RF2
|
|
51 USBID/RF3
|
|
|
|
TOP SIDE, LEFT-TO-RIGHT (if pin 1 is in upper left)
|
|
PIN NAME
|
|
---- ----------------------------
|
|
100 PMD4/RE4
|
|
99 PMD3/RE3
|
|
98 PMD2/RE2
|
|
97 TRD0/RG13
|
|
96 TRD1/RG12
|
|
95 TRD2/RG14
|
|
94 PMD1/RE1
|
|
93 PMD0/RE0
|
|
92 TRD3/RA7
|
|
91 TRCLK/RA6
|
|
90 PMD8/RG0
|
|
89 PMD9/RG1
|
|
88 PMD10/RF1
|
|
87 PMD11/RF0
|
|
86 ENVREG
|
|
85 Vcap/Vddcore
|
|
84 PMD15/CN16/RD7
|
|
83 PMD14/CN15/RD6
|
|
82 PMRD/CN14/RD5
|
|
81 OC5/PMWR/CN13/RD4
|
|
80 PMD13/CN19/RD13
|
|
79 IC5/PMD12/RD12
|
|
78 OC4/RD3
|
|
77 OC3/RD2
|
|
76 OC2/RD1
|
|
|
|
Additional Signals available from the board:
|
|
|
|
PROGRAM CONNECTOR: Vpp Vdd GND PGED1 PGEC1 NC PGED2 PGEC2
|
|
POWER POINTS: +5Vin +3.3V AVdd AGND Vdd GND USB+5V
|
|
|
|
MAX3232 Connection
|
|
==================
|
|
|
|
I use a tiny, MAX3232 board that I got from the eBay made by NKC
|
|
Electronics (http://www.nkcelectronics.com/). As of this writing, it
|
|
is also available here: http://www.nkcelectronics.com/rs232-to-ttl-3v--55v-convert232356.html
|
|
|
|
CTS -- Not connected
|
|
RTS -- Not connected
|
|
TX -- Pin 53: U1TX/RF8
|
|
RX -- Pin 52: U1RX/RF2
|
|
GND -- POWER POINT: GND
|
|
Vcc -- POWER POINT: Vdd (3.3V) -- Or P32_VBUS (+5V)
|
|
-- Or +5V from a USB PC port.
|
|
|
|
Toolchains
|
|
==========
|
|
|
|
I am using the free, LITE version of the PIC32MX toolchain available
|
|
for download from the microchip.com web site. I am using the Windows
|
|
version. The MicroChip toolchain is the only toolchaing currently
|
|
supported in these configurations, but it should be a simple matter to
|
|
adapt to other toolchains by modifying the Make.defs file include in
|
|
each configuration.
|
|
|
|
Toolchain Options:
|
|
|
|
CONFIG_PIC32MX_MICROCHIPW - MicroChip full toolchain for Windows
|
|
CONFIG_PIC32MX_MICROCHIPL - MicroChip full toolchain for Linux
|
|
CONFIG_PIC32MX_MICROCHIPW_LITE - MicroChip LITE toolchain for Windows
|
|
CONFIG_PIC32MX_MICROCHIPL_LITE - MicroChip LITE toolchain for Linux
|
|
|
|
Windows Native Toolchains
|
|
|
|
NOTE: There are several limitations to using a Windows based toolchain in a
|
|
Cygwin environment. The three biggest are:
|
|
|
|
1. The Windows toolchain cannot follow Cygwin paths. Path conversions are
|
|
performed automatically in the Cygwin makefiles using the 'cygpath' utility
|
|
but you might easily find some new path problems. If so, check out 'cygpath -w'
|
|
|
|
2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links
|
|
are used in Nuttx (e.g., include/arch). The make system works around these
|
|
problems for the Windows tools by copying directories instead of linking them.
|
|
But this can also cause some confusion for you: For example, you may edit
|
|
a file in a "linked" directory and find that your changes had no effect.
|
|
That is because you are building the copy of the file in the "fake" symbolic
|
|
directory. If you use a Windows toolchain, you should get in the habit of
|
|
making like this:
|
|
|
|
make clean_context all
|
|
|
|
An alias in your .bashrc file might make that less painful.
|
|
|
|
3. Dependencies are not made when using Windows versions of the GCC. This is
|
|
because the dependencies are generated using Windows pathes which do not
|
|
work with the Cygwin make.
|
|
|
|
Support has been added for making dependencies with the windows-native toolchains.
|
|
That support can be enabled by modifying your Make.defs file as follows:
|
|
|
|
- MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
|
+ MKDEP = $(TOPDIR)/tools/mkdeps.sh --winpaths "$(TOPDIR)"
|
|
|
|
If you have problems with the dependency build (for example, if you are not
|
|
building on C:), then you may need to modify tools/mkdeps.sh
|
|
|
|
Loading NuttX with PICkit2
|
|
==========================
|
|
|
|
NOTE: You need a PICKit3 if you plan to use the MPLAB debugger! The PICKit2
|
|
can, however, still be used to load programs. Instructions for the PICKit3
|
|
are similar.
|
|
|
|
Intel Hex Forma Files:
|
|
----------------------
|
|
|
|
When NuttX is built it will produce two files in the top-level NuttX
|
|
directory:
|
|
|
|
1) nuttx - This is an ELF file, and
|
|
2) nuttx.hex - This is an Intel Hex format file. This is controlled by
|
|
the setting CONFIG_INTELHEX_BINARY in the .config file.
|
|
|
|
The PICkit tool wants an Intel Hex format file to burn into FLASH. However,
|
|
there is a problem with the generated nutt.hex: The tool expects the nuttx.hex
|
|
file to contain physical addresses. But the nuttx.hex file generated from the
|
|
top-level make will have address in the KSEG0 and KSEG1 regions.
|
|
|
|
tools/mkpichex:
|
|
---------------
|
|
|
|
There is a simple tool in the configs/pcblogic-pic32mx/tools directory
|
|
that can be used to solve both issues with the nuttx.hex file. But,
|
|
first, you must build the the tools:
|
|
|
|
cd configs/pcblogic-pic32mx/tools
|
|
make
|
|
|
|
Now you will have an excecutable file call mkpichex (or mkpichex.exe on
|
|
Cygwin). This program will take the nutt.hex file as an input, it will
|
|
convert all of the KSEG0 and KSEG1 addresses to physical address, and
|
|
it will write the modified file, replacing the original nuttx.hex.
|
|
|
|
To use this file, you need to do the following things:
|
|
|
|
. ./setenv.sh # Source setenv.sh. Among other this, this script
|
|
# will add configs/pcblogic-pic32mx/tools to your
|
|
# PATH variable
|
|
make # Build nuttx and nuttx.hex
|
|
mkpichex $PWD # Convert addresses in nuttx.hex. $PWD is the path
|
|
# to the top-level build directory. It is the only
|
|
# required input to mkpichex.
|
|
|
|
PIC32MX Configuration Options
|
|
=============================
|
|
|
|
General Architecture Settings:
|
|
|
|
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
|
|
be set to:
|
|
|
|
CONFIG_ARCH=mips
|
|
|
|
CONFIG_ARCH_family - For use in C code:
|
|
|
|
CONFIG_ARCH_MIPS=y
|
|
|
|
CONFIG_ARCH_architecture - For use in C code:
|
|
|
|
CONFIG_ARCH_MIPS32=y
|
|
|
|
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
|
|
|
CONFIG_ARCH_CHIP=pic32mx
|
|
|
|
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
|
|
chip:
|
|
|
|
CONFIG_ARCH_CHIP_PIC32MX460F512L=y
|
|
|
|
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
|
|
hence, the board that supports the particular chip or SoC.
|
|
|
|
CONFIG_ARCH_BOARD=pcblogic-pic32mx
|
|
|
|
CONFIG_ARCH_BOARD_name - For use in C code
|
|
|
|
CONFIG_ARCH_BOARD_PCBLOGICPIC32MX=y
|
|
|
|
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
|
|
of delay loops
|
|
|
|
CONFIG_ENDIAN_BIG - define if big endian (default is little
|
|
endian)
|
|
|
|
CONFIG_DRAM_SIZE - Describes the installed DRAM (CPU SRAM in this case):
|
|
|
|
CONFIG_DRAM_SIZE=(32*1024) (32Kb)
|
|
|
|
There is an additional 32Kb of SRAM in AHB SRAM banks 0 and 1.
|
|
|
|
CONFIG_DRAM_START - The start address of installed DRAM
|
|
|
|
CONFIG_DRAM_START=0x10000000
|
|
|
|
CONFIG_DRAM_END - Last address+1 of installed RAM
|
|
|
|
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
|
|
|
|
CONFIG_ARCH_IRQPRIO - The PIC32MXx supports interrupt prioritization
|
|
|
|
CONFIG_ARCH_IRQPRIO=y
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
|
|
have LEDs
|
|
|
|
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
|
stack. If defined, this symbol is the size of the interrupt
|
|
stack in bytes. If not defined, the user task stacks will be
|
|
used during interrupt handling.
|
|
|
|
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
|
|
|
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
|
cause a 100 second delay during boot-up. This 100 second delay
|
|
serves no purpose other than it allows you to calibratre
|
|
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
|
|
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
|
|
the delay actually is 100 seconds.
|
|
|
|
PIC32MX Configuration
|
|
|
|
CONFIG_PIC32MX_MVEC - Select muli- vs. single-vectored interrupts
|
|
|
|
Individual subsystems can be enabled:
|
|
|
|
CONFIG_PIC32MX_WDT - Watchdog timer
|
|
CONFIG_PIC32MX_T2 - Timer 2 (Timer 1 is the system time and always enabled)
|
|
CONFIG_PIC32MX_T3 - Timer 3
|
|
CONFIG_PIC32MX_T4 - Timer 4
|
|
CONFIG_PIC32MX_T5 - Timer 5
|
|
CONFIG_PIC32MX_IC1 - Input Capture 1
|
|
CONFIG_PIC32MX_IC2 - Input Capture 2
|
|
CONFIG_PIC32MX_IC3 - Input Capture 3
|
|
CONFIG_PIC32MX_IC4 - Input Capture 4
|
|
CONFIG_PIC32MX_IC5 - Input Capture 5
|
|
CONFIG_PIC32MX_OC1 - Output Compare 1
|
|
CONFIG_PIC32MX_OC2 - Output Compare 2
|
|
CONFIG_PIC32MX_OC3 - Output Compare 3
|
|
CONFIG_PIC32MX_OC4 - Output Compare 4
|
|
CONFIG_PIC32MX_OC5 - Output Compare 5
|
|
CONFIG_PIC32MX_I2C1 - I2C 1
|
|
CONFIG_PIC32MX_I2C2 - I2C 2
|
|
CONFIG_PIC32MX_SPI1 - SPI 1
|
|
CONFIG_PIC32MX_SPI2 - SPI 2
|
|
CONFIG_PIC32MX_UART1 - UART 1
|
|
CONFIG_PIC32MX_UART2 - UART 2
|
|
CONFIG_PIC32MX_ADC - ADC 1
|
|
CONFIG_PIC32MX_PMP - Parallel Master Port
|
|
CONFIG_PIC32MX_CM1 - Comparator 1
|
|
CONFIG_PIC32MX_CM2 - Comparator 2
|
|
CONFIG_PIC32MX_RTCC - Real-Time Clock and Calendar
|
|
CONFIG_PIC32MX_DMA - DMA
|
|
CONFIG_PIC32MX_FLASH - FLASH
|
|
CONFIG_PIC32MX_USBDEV - USB device
|
|
CONFIG_PIC32MX_USBHOST - USB host
|
|
|
|
PIC32MX Configuration Settings
|
|
DEVCFG0:
|
|
CONFIG_PIC32MX_DEBUGGER - Background Debugger Enable. Default 3 (disabled). The
|
|
value 2 enables.
|
|
CONFIG_PIC32MX_ICESEL - In-Circuit Emulator/Debugger Communication Channel Select
|
|
Default 1 (PG2)
|
|
CONFIG_PIC32MX_PROGFLASHWP - Program FLASH write protect. Default 0xff (disabled)
|
|
CONFIG_PIC32MX_BOOTFLASHWP - Default 1 (disabled)
|
|
CONFIG_PIC32MX_CODEWP - Default 1 (disabled)
|
|
DEVCFG1: (All settings determined by selections in board.h)
|
|
DEVCFG2: (All settings determined by selections in board.h)
|
|
DEVCFG3:
|
|
CONFIG_PIC32MX_USBIDO - USB USBID Selection. Default 1 if USB enabled
|
|
(USBID pin is controlled by the USB module), but 0 (GPIO) otherwise.
|
|
CONFIG_PIC32MX_VBUSIO - USB VBUSON Selection (Default 1 if USB enabled
|
|
(VBUSON pin is controlled by the USB module, but 0 (GPIO) otherwise.
|
|
CONFIG_PIC32MX_WDENABLE - Enabled watchdog on power up. Default 0 (watchdog
|
|
can be enabled later by software).
|
|
|
|
The priority of interrupts may be specified. The value ranage of
|
|
priority is 4-31. The default (16) will be used if these any of these
|
|
are undefined.
|
|
|
|
CONFIG_PIC32MX_CTPRIO - Core Timer Interrupt
|
|
CONFIG_PIC32MX_CS0PRIO - Core Software Interrupt 0
|
|
CONFIG_PIC32MX_CS1PRIO - Core Software Interrupt 1
|
|
CONFIG_PIC32MX_INT0PRIO - External Interrupt 0
|
|
CONFIG_PIC32MX_INT1PRIO - External Interrupt 1
|
|
CONFIG_PIC32MX_INT2PRIO - External Interrupt 2
|
|
CONFIG_PIC32MX_INT3PRIO - External Interrupt 3
|
|
CONFIG_PIC32MX_INT4PRIO - External Interrupt 4
|
|
CONFIG_PIC32MX_FSCMPRIO - Fail-Safe Clock Monitor
|
|
CONFIG_PIC32MX_T1PRIO - Timer 1 (System timer) priority
|
|
CONFIG_PIC32MX_T2PRIO - Timer 2 priority
|
|
CONFIG_PIC32MX_T3PRIO - Timer 3 priority
|
|
CONFIG_PIC32MX_T4PRIO - Timer 4 priority
|
|
CONFIG_PIC32MX_T5PRIO - Timer 5 priority
|
|
CONFIG_PIC32MX_IC1PRIO - Input Capture 1
|
|
CONFIG_PIC32MX_IC2PRIO - Input Capture 2
|
|
CONFIG_PIC32MX_IC3PRIO - Input Capture 3
|
|
CONFIG_PIC32MX_IC4PRIO - Input Capture 4
|
|
CONFIG_PIC32MX_IC5PRIO - Input Capture 5
|
|
CONFIG_PIC32MX_OC1PRIO - Output Compare 1
|
|
CONFIG_PIC32MX_OC2PRIO - Output Compare 2
|
|
CONFIG_PIC32MX_OC3PRIO - Output Compare 3
|
|
CONFIG_PIC32MX_OC4PRIO - Output Compare 4
|
|
CONFIG_PIC32MX_OC5PRIO - Output Compare 5
|
|
CONFIG_PIC32MX_I2C1PRIO - I2C 1
|
|
CONFIG_PIC32MX_I2C2PRIO - I2C 2
|
|
CONFIG_PIC32MX_SPI1PRIO - SPI 1
|
|
CONFIG_PIC32MX_SPI2PRIO - SPI 2
|
|
CONFIG_PIC32MX_UART1PRIO - UART 1
|
|
CONFIG_PIC32MX_UART2PRIO - UART 2
|
|
CONFIG_PIC32MX_CN - Input Change Interrupt
|
|
CONFIG_PIC32MX_ADCPRIO - ADC1 Convert Done
|
|
CONFIG_PIC32MX_PMPPRIO - Parallel Master Port
|
|
CONFIG_PIC32MX_CM1PRIO - Comparator 1
|
|
CONFIG_PIC32MX_CM2PRIO - Comparator 2
|
|
CONFIG_PIC32MX_FSCMPRIO - Fail-Safe Clock Monitor
|
|
CONFIG_PIC32MX_RTCCPRIO - Real-Time Clock and Calendar
|
|
CONFIG_PIC32MX_DMA0PRIO - DMA Channel 0
|
|
CONFIG_PIC32MX_DMA1PRIO - DMA Channel 1
|
|
CONFIG_PIC32MX_DMA2PRIO - DMA Channel 2
|
|
CONFIG_PIC32MX_DMA3PRIO - DMA Channel 3
|
|
CONFIG_PIC32MX_FCEPRIO - Flash Control Event
|
|
CONFIG_PIC32MX_USBPRIO - USB
|
|
|
|
PIC32MXx specific device driver settings
|
|
|
|
CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
|
console and ttys0 (default is the UART0).
|
|
CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
|
This specific the size of the receive buffer
|
|
CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
|
being sent. This specific the size of the transmit buffer
|
|
CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
|
|
CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
|
CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
|
CONFIG_UARTn_2STOP - Two stop bits
|
|
|
|
PIC32MXx USB Device Configuration
|
|
|
|
PIC32MXx USB Host Configuration (the PIC32MX does not support USB Host)
|
|
|
|
Configurations
|
|
==============
|
|
|
|
Each PIC32MX configuration is maintained in a sudirectory and can be
|
|
selected as follow:
|
|
|
|
cd tools
|
|
./configure.sh pcblogic-pic32mx/<subdir>
|
|
cd -
|
|
. ./setenv.sh
|
|
|
|
Where <subdir> is one of the following:
|
|
|
|
ostest:
|
|
This configuration directory, performs a simple OS test using
|
|
apps/examples/ostest.
|