dark0707
/
px4-firmware
forked from Archive/PX4-Autopilot
1
0
Fork 0
Code Pull Requests Activity
px4-firmware/nuttx/configs/shenzhou/README.txt

690 lines
28 KiB
Plaintext
Raw Blame History

README
======
This README discusses issues unique to NuttX configurations for the Shenzhou
development board from www.armjishu.com featuring the STMicro STM32F107VCT
MCU. On-board features:
- STM32F107VCT
- 10/100M PHY (DM9161AEP)
- TFT LCD Connector
- USB OTG
- CAN (CAN1=2)
- USART connectos (USART1-2)
- RS-485
- SD card slot
- Audio DAC (PCM1770)
- SPI Flash (W25X16)
- (4) LEDs (LED1-4)
- 2.4G Wireless (NRF24L01 SPI module)
- 315MHz Wireless (module)
- (4) Buttons (KEY1-4, USERKEY2, USERKEY, TEMPER, WAKEUP)
- VBUS/external +4V select
- 5V/3.3V power conversion
- Extension connector
- JTAG
Contents
========
- STM32F107VCT Pin Usage
- Development Environment
- GNU Toolchain Options
- IDEs
- NuttX buildroot Toolchain
- Shenzhou-specific Configuration Options
- LEDs
- Shenzhou-specific Configuration Options
- Configurations
STM32F107VCT Pin Usage
======================
-- ---- -------------- -------------------------------------------------------------------
PN NAME SIGNAL NOTES
-- ---- -------------- -------------------------------------------------------------------
23 PA0 WAKEUP Connected to KEY4. Active low: Closing KEY4 pulls WAKEUP to ground.
24 PA1 MII_RX_CLK
RMII_REF_CLK
25 PA2 MII_MDIO
26 PA3 315M_VT
29 PA4 DAC_OUT1 To CON5(CN14)
30 PA5 DAC_OUT2 To CON5(CN14). JP10
SPI1_SCK To the SD card, SPI FLASH
31 PA6 SPI1_MISO To the SD card, SPI FLASH
32 PA7 SPI1_MOSI To the SD card, SPI FLASH
67 PA8 MCO To DM9161AEP PHY
68 PA9 USB_VBUS MINI-USB-AB. JP3
USART1_TX MAX3232 to CN5
69 PA10 USB_ID MINI-USB-AB. JP5
USART1_RX MAX3232 to CN5
70 PA11 USB_DM MINI-USB-AB
71 PA12 USB_DP MINI-USB-AB
72 PA13 TMS/SWDIO
76 PA14 TCK/SWCLK
77 PA15 TDI
-- ---- -------------- -------------------------------------------------------------------
PN NAME SIGNAL NOTES
-- ---- -------------- -------------------------------------------------------------------
35 PB0 ADC_IN1 To CON5(CN14)
36 PB1 ADC_IN2 To CON5(CN14)
37 PB2 DATA_LE To TFT LCD (CN13)
BOOT1 JP13
89 PB3 TDO/SWO
90 PB4 TRST
91 PB5 CAN2_RX
92 PB6 CAN2_TX JP11
I2C1_SCL
93 PB7 I2C1_SDA
95 PB8 USB_PWR Drives USB VBUS
96 PB9 F_CS To both the TFT LCD (CN13) and to the W25X16 SPI FLASH
47 PB10 USERKEY Connected to KEY2
48 PB11 MII_TX_EN Ethernet PHY
51 PB12 I2S_WS Audio DAC
MII_TXD0 Ethernet PHY
52 PB13 I2S_CK Audio DAC
MII_TXD1 Ethernet PHY
53 PB14 SD_CD
54 PB15 I2S_DIN Audio DAC
-- ---- -------------- -------------------------------------------------------------------
PN NAME SIGNAL NOTES
-- ---- -------------- -------------------------------------------------------------------
15 PC0 POTENTIO_METER
16 PC1 MII_MDC Ethernet PHY
17 PC2 WIRELESS_INT
18 PC3 WIRELESS_CE To the NRF24L01 2.4G wireless module
33 PC4 USERKEY2 Connected to KEY1
34 PC5 TP_INT JP6. To TFT LCD (CN13) module
MII_INT Ethernet PHY
63 PC6 I2S_MCK Audio DAC. Active low: Pulled high
64 PC7 PCM1770_CS Audio DAC. Active low: Pulled high
65 PC8 LCD_CS TFT LCD (CN13). Active low: Pulled high
66 PC9 TP_CS TFT LCD (CN13). Active low: Pulled high
78 PC10 SPI3_SCK To TFT LCD (CN13), the NRF24L01 2.4G wireless module
79 PC11 SPI3_MISO To TFT LCD (CN13), the NRF24L01 2.4G wireless module
80 PC12 SPI3_MOSI To TFT LCD (CN13), the NRF24L01 2.4G wireless module
7 PC13 TAMPER Connected to KEY3
8 PC14 OSC32_IN Y1 32.768Khz XTAL
9 PC15 OSC32_OUT Y1 32.768Khz XTAL
-- ---- -------------- -------------------------------------------------------------------
PN NAME SIGNAL NOTES
-- ---- -------------- -------------------------------------------------------------------
81 PD0 CAN1_RX
82 PD1 CAN1_TX
83 PD2 LED1 Active low: Pulled high
84 PD3 LED2 Active low: Pulled high
85 PD4 LED3 Active low: Pulled high
86 PD5 485_TX Same as USART2_TX but goes to SP3485
USART2_TX MAX3232 to CN6
87 PD6 485_RX Save as USART2_RX but goes to SP3485 (see JP4)
USART2_RX MAX3232 to CN6
88 PD7 LED4 Active low: Pulled high
485_DIR SP3485 read enable (not)
55 PD8 MII_RX_DV Ethernet PHY
RMII_CRSDV Ethernet PHY
56 PD9 MII_RXD0 Ethernet PHY
57 PD10 MII_RXD1 Ethernet PHY
58 PD11 SD_CS Active low: Pulled high
59 PD12 WIRELESS_CS To the NRF24L01 2.4G wireless module
60 PD13 LCD_RS To TFT LCD (CN13)
61 PD14 LCD_WR To TFT LCD (CN13)
62 PD15 LCD_RD To TFT LCD (CN13)
-- ---- -------------- -------------------------------------------------------------------
PN NAME SIGNAL NOTES
-- ---- -------------- -------------------------------------------------------------------
97 PE0 DB00 To TFT LCD (CN13)
98 PE1 DB01 To TFT LCD (CN13)
1 PE2 DB02 To TFT LCD (CN13)
2 PE3 DB03 To TFT LCD (CN13)
3 PE4 DB04 To TFT LCD (CN13)
4 PE5 DB05 To TFT LCD (CN13)
5 PE6 DB06 To TFT LCD (CN13)
38 PE7 DB07 To TFT LCD (CN13)
39 PE8 DB08 To TFT LCD (CN13)
40 PE9 DB09 To TFT LCD (CN13)
41 PE10 DB10 To TFT LCD (CN13)
42 PE11 DB11 To TFT LCD (CN13)
43 PE12 DB12 To TFT LCD (CN13)
44 PE13 DB13 To TFT LCD (CN13)
45 PE14 DB14 To TFT LCD (CN13)
46 PE15 DB15 To TFT LCD (CN13)
-- ---- -------------- -------------------------------------------------------------------
PN NAME SIGNAL NOTES
-- ---- -------------- -------------------------------------------------------------------
73 N/C
12 OSC_IN Y2 25Mhz XTAL
13 OSC_OUT Y2 25Mhz XTAL
94 BOOT0 JP15 (3.3V or GND)
14 RESET S5
6 VBAT JP14 (3.3V or battery)
49 VSS_1 GND
74 VSS_2 GND
99 VSS_3 GND
27 VSS_4 GND
10 VSS_5 GND
19 VSSA VSSA
20 VREF- VREF-
Development Environment
=======================
Either Linux or Cygwin on Windows can be used for the development environment.
The source has been built only using the GNU toolchain (see below). Other
toolchains will likely cause problems. Testing was performed using the Cygwin
environment because the development tools that I used only work under Windows.
GNU Toolchain Options
=====================
Toolchain Configurations
------------------------
The NuttX make system has been modified to support the following different
toolchain options.
1. The CodeSourcery GNU toolchain,
2. The Atollic Toolchain,
3. The devkitARM GNU toolchain,
4. Raisonance GNU toolchain, or
5. The NuttX buildroot Toolchain (see below).
Most testing has been conducted using the CodeSourcery toolchain for Windows and
that is the default toolchain in most configurations. To use the Atollic,
devkitARM, Raisonance GNU, or NuttX buildroot toolchain, you simply need to
add one of the following configuration options to your .config (or defconfig)
file:
CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows
CONFIG_STM32_CODESOURCERYL=y : CodeSourcery under Linux
CONFIG_STM32_ATOLLIC_LITE=y : The free, "Lite" version of Atollic toolchain under Windows
CONFIG_STM32_ATOLLIC_PRO=y : The paid, "Pro" version of Atollic toolchain under Windows
CONFIG_STM32_DEVKITARM=y : devkitARM under Windows
CONFIG_STM32_RAISONANCE=y : Raisonance RIDE7 under Windows
CONFIG_STM32_BUILDROOT=y : NuttX buildroot under Linux or Cygwin (default)
If you change the default toolchain, then you may also have to modify the PATH in
the setenv.h file if your make cannot find the tools.
NOTE: the CodeSourcery (for Windows), Atollic, devkitARM, and Raisonance toolchains are
Windows native toolchains. The CodeSourcery (for Linux) and NuttX buildroot
toolchains are Cygwin and/or Linux native toolchains. There are several limitations
to using a Windows based toolchain in a Cygwin environment. The three biggest are:
1. The Windows toolchain cannot follow Cygwin paths. Path conversions are
performed automatically in the Cygwin makefiles using the 'cygpath' utility
but you might easily find some new path problems. If so, check out 'cygpath -w'
2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links
are used in Nuttx (e.g., include/arch). The make system works around these
problems for the Windows tools by copying directories instead of linking them.
But this can also cause some confusion for you: For example, you may edit
a file in a "linked" directory and find that your changes had no effect.
That is because you are building the copy of the file in the "fake" symbolic
directory. If you use a Windows toolchain, you should get in the habit of
making like this:
make clean_context all
An alias in your .bashrc file might make that less painful.
3. Dependencies are not made when using Windows versions of the GCC. This is
because the dependencies are generated using Windows pathes which do not
work with the Cygwin make.
Support has been added for making dependencies with the windows-native toolchains.
That support can be enabled by modifying your Make.defs file as follows:
- MKDEP = $(TOPDIR)/tools/mknulldeps.sh
+ MKDEP = $(TOPDIR)/tools/mkdeps.sh --winpaths "$(TOPDIR)"
If you have problems with the dependency build (for example, if you are not
building on C:), then you may need to modify tools/mkdeps.sh
The CodeSourcery Toolchain (2009q1)
-----------------------------------
The CodeSourcery toolchain (2009q1) does not work with default optimization
level of -Os (See Make.defs). It will work with -O0, -O1, or -O2, but not with
-Os.
The Atollic "Pro" and "Lite" Toolchain
--------------------------------------
One problem that I had with the Atollic toolchains is that the provide a gcc.exe
and g++.exe in the same bin/ file as their ARM binaries. If the Atollic bin/ path
appears in your PATH variable before /usr/bin, then you will get the wrong gcc
when you try to build host executables. This will cause to strange, uninterpretable
errors build some host binaries in tools/ when you first make.
The Atollic "Lite" Toolchain
----------------------------
The free, "Lite" version of the Atollic toolchain does not support C++ nor
does it support ar, nm, objdump, or objdcopy. If you use the Atollic "Lite"
toolchain, you will have to set:
CONFIG_HAVE_CXX=n
In order to compile successfully. Otherwise, you will get errors like:
"C++ Compiler only available in TrueSTUDIO Professional"
The make may then fail in some of the post link processing because of some of
the other missing tools. The Make.defs file replaces the ar and nm with
the default system x86 tool versions and these seem to work okay. Disable all
of the following to avoid using objcopy:
CONFIG_RRLOAD_BINARY=n
CONFIG_INTELHEX_BINARY=n
CONFIG_MOTOROLA_SREC=n
CONFIG_RAW_BINARY=n
devkitARM
---------
The devkitARM toolchain includes a version of MSYS make. Make sure that the
the paths to Cygwin's /bin and /usr/bin directories appear BEFORE the devkitARM
path or will get the wrong version of make.
IDEs
====
NuttX is built using command-line make. It can be used with an IDE, but some
effort will be required to create the project.
Makefile Build
--------------
Under Eclipse, it is pretty easy to set up an "empty makefile project" and
simply use the NuttX makefile to build the system. That is almost for free
under Linux. Under Windows, you will need to set up the "Cygwin GCC" empty
makefile project in order to work with Windows (Google for "Eclipse Cygwin" -
there is a lot of help on the internet).
Native Build
------------
Here are a few tips before you start that effort:
1) Select the toolchain that you will be using in your .config file
2) Start the NuttX build at least one time from the Cygwin command line
before trying to create your project. This is necessary to create
certain auto-generated files and directories that will be needed.
3) Set up include pathes: You will need include/, arch/arm/src/stm32,
arch/arm/src/common, arch/arm/src/armv7-m, and sched/.
4) All assembly files need to have the definition option -D __ASSEMBLY__
on the command line.
Startup files will probably cause you some headaches. The NuttX startup file
is arch/arm/src/stm32/stm32_vectors.S. With RIDE, I have to build NuttX
one time from the Cygwin command line in order to obtain the pre-built
startup object needed by RIDE.
NuttX buildroot Toolchain
=========================
A GNU GCC-based toolchain is assumed. The files */setenv.sh should
be modified to point to the correct path to the Cortex-M3 GCC toolchain (if
different from the default in your PATH variable).
If you have no Cortex-M3 toolchain, one can be downloaded from the NuttX
SourceForge download site (https://sourceforge.net/projects/nuttx/files/buildroot/).
This GNU toolchain builds and executes in the Linux or Cygwin environment.
1. You must have already configured Nuttx in <some-dir>/nuttx.
cd tools
./configure.sh shenzhou/<sub-dir>
2. Download the latest buildroot package into <some-dir>
3. unpack the buildroot tarball. The resulting directory may
have versioning information on it like buildroot-x.y.z. If so,
rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.
4. cd <some-dir>/buildroot
5. cp configs/cortexm3-defconfig-4.3.3 .config
6. make oldconfig
7. make
8. Edit setenv.h, if necessary, so that the PATH variable includes
the path to the newly built binaries.
See the file configs/README.txt in the buildroot source tree. That has more
detailed PLUS some special instructions that you will need to follow if you are
building a Cortex-M3 toolchain for Cygwin under Windows.
LEDs
====
The Shenzhou board has four LEDs labeled LED1, LED2, LED3 and LED4 on the
board. These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
defined. In that case, the usage by the board port is defined in
include/board.h and src/up_leds.c. The LEDs are used to encode OS-related
events as follows:
SYMBOL Meaning LED1* LED2 LED3 LED4****
------------------- ----------------------- ------- ------- ------- ------
LED_STARTED NuttX has been started ON OFF OFF OFF
LED_HEAPALLOCATE Heap has been allocated OFF ON OFF OFF
LED_IRQSENABLED Interrupts enabled ON ON OFF OFF
LED_STACKCREATED Idle stack created OFF OFF ON OFF
LED_INIRQ In an interrupt** ON N/C N/C OFF
LED_SIGNAL In a signal handler*** N/C ON N/C OFF
LED_ASSERTION An assertion failed ON ON N/C OFF
LED_PANIC The system has crashed N/C N/C N/C ON
LED_IDLE STM32 is is sleep mode (Optional, not used)
* If LED1, LED2, LED3 are statically on, then NuttX probably failed to boot
and these LEDs will give you some indication of where the failure was
** The normal state is LED3 ON and LED1 faintly glowing. This faint glow
is because of timer interupts that result in the LED being illuminated
on a small proportion of the time.
*** LED2 may also flicker normally if signals are processed.
**** LED4 may not be available if RS-485 is also used it will then indicate
the RS-485 direction.
Shenzhou-specific Configuration Options
============================================
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
be set to:
CONFIG_ARCH=arm
CONFIG_ARCH_family - For use in C code:
CONFIG_ARCH_ARM=y
CONFIG_ARCH_architecture - For use in C code:
CONFIG_ARCH_CORTEXM3=y
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
CONFIG_ARCH_CHIP=stm32
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
chip:
CONFIG_ARCH_CHIP_STM32F107VC=y
CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG - Enables special STM32 clock
configuration features.
CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG=n
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
hence, the board that supports the particular chip or SoC.
CONFIG_ARCH_BOARD=shenzhou (for the Shenzhou development board)
CONFIG_ARCH_BOARD_name - For use in C code
CONFIG_ARCH_BOARD_SHENZHOU=y
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
of delay loops
CONFIG_ENDIAN_BIG - define if big endian (default is little
endian)
CONFIG_DRAM_SIZE - Describes the installed DRAM (SRAM in this case):
CONFIG_DRAM_SIZE=0x00010000 (64Kb)
CONFIG_DRAM_START - The start address of installed DRAM
CONFIG_DRAM_START=0x20000000
CONFIG_STM32_CCMEXCLUDE - Exclude CCM SRAM from the HEAP
CONFIG_ARCH_IRQPRIO - The STM32107xxx supports interrupt prioritization
CONFIG_ARCH_IRQPRIO=y
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
have LEDs
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
stack. If defined, this symbol is the size of the interrupt
stack in bytes. If not defined, the user task stacks will be
used during interrupt handling.
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
cause a 100 second delay during boot-up. This 100 second delay
serves no purpose other than it allows you to calibratre
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
the delay actually is 100 seconds.
Individual subsystems can be enabled:
AHB
---
CONFIG_STM32_DMA1
CONFIG_STM32_DMA2
CONFIG_STM32_CRC
CONFIG_STM32_ETHMAC
CONFIG_STM32_OTGFS
CONFIG_STM32_IWDG
CONFIG_STM32_PWR -- Required for RTC
APB1 (low speed)
----------------
CONFIG_STM32_BKP
CONFIG_STM32_TIM2
CONFIG_STM32_TIM3
CONFIG_STM32_TIM4
CONFIG_STM32_TIM5
CONFIG_STM32_TIM6
CONFIG_STM32_TIM7
CONFIG_STM32_USART2
CONFIG_STM32_USART3
CONFIG_STM32_UART4
CONFIG_STM32_UART5
CONFIG_STM32_SPI2
CONFIG_STM32_SPI3
CONFIG_STM32_I2C1
CONFIG_STM32_I2C2
CONFIG_STM32_CAN1
CONFIG_STM32_CAN2
CONFIG_STM32_DAC1
CONFIG_STM32_DAC2
CONFIG_STM32_WWDG
APB2 (high speed)
-----------------
CONFIG_STM32_TIM1
CONFIG_STM32_SPI1
CONFIG_STM32_USART1
CONFIG_STM32_ADC1
CONFIG_STM32_ADC2
Timer devices may be used for different purposes. One special purpose is
to generate modulated outputs for such things as motor control. If CONFIG_STM32_TIMn
is defined (as above) then the following may also be defined to indicate that
the timer is intended to be used for pulsed output modulation, ADC conversion,
or DAC conversion. Note that ADC/DAC require two definition: Not only do you have
to assign the timer (n) for used by the ADC or DAC, but then you also have to
configure which ADC or DAC (m) it is assigned to.
CONFIG_STM32_TIMn_PWM Reserve timer n for use by PWM, n=1,..,14
CONFIG_STM32_TIMn_ADC Reserve timer n for use by ADC, n=1,..,14
CONFIG_STM32_TIMn_ADCm Reserve timer n to trigger ADCm, n=1,..,14, m=1,..,3
CONFIG_STM32_TIMn_DAC Reserve timer n for use by DAC, n=1,..,14
CONFIG_STM32_TIMn_DACm Reserve timer n to trigger DACm, n=1,..,14, m=1,..,2
For each timer that is enabled for PWM usage, we need the following additional
configuration settings:
CONFIG_STM32_TIMx_CHANNEL - Specifies the timer output channel {1,..,4}
NOTE: The STM32 timers are each capable of generating different signals on
each of the four channels with different duty cycles. That capability is
not supported by this driver: Only one output channel per timer.
JTAG Enable settings (by default JTAG-DP and SW-DP are disabled):
CONFIG_STM32_JTAG_FULL_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
CONFIG_STM32_JTAG_NOJNTRST_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
but without JNTRST.
CONFIG_STM32_JTAG_SW_ENABLE - Set JTAG-DP disabled and SW-DP enabled
STM32107xxx specific device driver settings
CONFIG_U[S]ARTn_SERIAL_CONSOLE - selects the USARTn (n=1,2,3) or UART
m (m=4,5) for the console and ttys0 (default is the USART1).
CONFIG_U[S]ARTn_RXBUFSIZE - Characters are buffered as received.
This specific the size of the receive buffer
CONFIG_U[S]ARTn_TXBUFSIZE - Characters are buffered before
being sent. This specific the size of the transmit buffer
CONFIG_U[S]ARTn_BAUD - The configure BAUD of the UART. Must be
CONFIG_U[S]ARTn_BITS - The number of bits. Must be either 7 or 8.
CONFIG_U[S]ARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
CONFIG_U[S]ARTn_2STOP - Two stop bits
CONFIG_STM32_SPI_INTERRUPTS - Select to enable interrupt driven SPI
support. Non-interrupt-driven, poll-waiting is recommended if the
interrupt rate would be to high in the interrupt driven case.
CONFIG_STM32_SPI_DMA - Use DMA to improve SPI transfer performance.
Cannot be used with CONFIG_STM32_SPI_INTERRUPT.
CONFIG_STM32_PHYADDR - The 5-bit address of the PHY on the board
CONFIG_STM32_MII - Support Ethernet MII interface
CONFIG_STM32_MII_MCO1 - Use MCO1 to clock the MII interface
CONFIG_STM32_MII_MCO2 - Use MCO2 to clock the MII interface
CONFIG_STM32_RMII - Support Ethernet RMII interface
CONFIG_STM32_AUTONEG - Use PHY autonegotion to determine speed and mode
CONFIG_STM32_ETHFD - If CONFIG_STM32_AUTONEG is not defined, then this
may be defined to select full duplex mode. Default: half-duplex
CONFIG_STM32_ETH100MBPS - If CONFIG_STM32_AUTONEG is not defined, then this
may be defined to select 100 MBps speed. Default: 10 Mbps
CONFIG_STM32_PHYSR - This must be provided if CONFIG_STM32_AUTONEG is
defined. The PHY status register address may diff from PHY to PHY. This
configuration sets the address of the PHY status register.
CONFIG_STM32_PHYSR_SPEED - This must be provided if CONFIG_STM32_AUTONEG is
defined. This provides bit mask indicating 10 or 100MBps speed.
CONFIG_STM32_PHYSR_100MBPS - This must be provided if CONFIG_STM32_AUTONEG is
defined. This provides the value of the speed bit(s) indicating 100MBps speed.
CONFIG_STM32_PHYSR_MODE - This must be provided if CONFIG_STM32_AUTONEG is
defined. This provide bit mask indicating full or half duplex modes.
CONFIG_STM32_PHYSR_FULLDUPLEX - This must be provided if CONFIG_STM32_AUTONEG is
defined. This provides the value of the mode bits indicating full duplex mode.
CONFIG_STM32_ETH_PTP - Precision Time Protocol (PTP). Not supported
but some hooks are indicated with this condition.
Shenzhou CAN Configuration
CONFIG_CAN - Enables CAN support (one or both of CONFIG_STM32_CAN1 or
CONFIG_STM32_CAN2 must also be defined)
CONFIG_CAN_FIFOSIZE - The size of the circular buffer of CAN messages.
Default: 8
CONFIG_CAN_NPENDINGRTR - The size of the list of pending RTR requests.
Default: 4
CONFIG_CAN_LOOPBACK - A CAN driver may or may not support a loopback
mode for testing. The STM32 CAN driver does support loopback mode.
CONFIG_CAN1_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN1 is defined.
CONFIG_CAN2_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN2 is defined.
CONFIG_CAN_TSEG1 - The number of CAN time quanta in segment 1. Default: 6
CONFIG_CAN_TSEG2 - the number of CAN time quanta in segment 2. Default: 7
CONFIG_CAN_REGDEBUG - If CONFIG_DEBUG is set, this will generate an
dump of all CAN registers.
Shenzhou LCD Hardware Configuration
The LCD driver supports the following LCDs on the STM324xG_EVAL board:
AM-240320L8TNQW00H (LCD_ILI9320 or LCD_ILI9321) OR
AM-240320D5TOQW01H (LCD_ILI9325)
Configuration options.
CONFIG_LCD_LANDSCAPE - Define for 320x240 display "landscape"
support. Default is this 320x240 "landscape" orientation
For the Shenzhou board, the edge opposite from the row of buttons
is used as the top of the display in this orientation.
CONFIG_LCD_RLANDSCAPE - Define for 320x240 display "reverse
landscape" support. Default is this 320x240 "landscape"
orientation
For the Shenzhou board, the edge next to the row of buttons
is used as the top of the display in this orientation.
CONFIG_LCD_PORTRAIT - Define for 240x320 display "portrait"
orientation support.
CONFIG_LCD_RPORTRAIT - Define for 240x320 display "reverse
portrait" orientation support.
CONFIG_LCD_RDSHIFT - When reading 16-bit gram data, there appears
to be a shift in the returned data. This value fixes the offset.
Default 5.
The LCD driver dynamically selects the LCD based on the reported LCD
ID value. However, code size can be reduced by suppressing support for
individual LCDs using:
CONFIG_STM32_ILI9320_DISABLE (includes ILI9321)
CONFIG_STM32_ILI9325_DISABLE
STM32 USB OTG FS Host Driver Support
Pre-requisites
CONFIG_USBHOST - Enable USB host support
CONFIG_STM32_OTGFS - Enable the STM32 USB OTG FS block
CONFIG_STM32_SYSCFG - Needed
CONFIG_SCHED_WORKQUEUE - Worker thread support is required
Options:
CONFIG_STM32_OTGFS_RXFIFO_SIZE - Size of the RX FIFO in 32-bit words.
Default 128 (512 bytes)
CONFIG_STM32_OTGFS_NPTXFIFO_SIZE - Size of the non-periodic Tx FIFO
in 32-bit words. Default 96 (384 bytes)
CONFIG_STM32_OTGFS_PTXFIFO_SIZE - Size of the periodic Tx FIFO in 32-bit
words. Default 96 (384 bytes)
CONFIG_STM32_OTGFS_DESCSIZE - Maximum size of a descriptor. Default: 128
CONFIG_STM32_OTGFS_SOFINTR - Enable SOF interrupts. Why would you ever
want to do that?
CONFIG_STM32_USBHOST_REGDEBUG - Enable very low-level register access
debug. Depends on CONFIG_DEBUG.
CONFIG_STM32_USBHOST_PKTDUMP - Dump all incoming and outgoing USB
packets. Depends on CONFIG_DEBUG.
Configurations
==============
Each Shenzhou configuration is maintained in a sudirectory and
can be selected as follow:
cd tools
./configure.sh shenzhou/<subdir>
cd -
. ./setenv.sh
Where <subdir> is one of the following:
nsh:
---
Configures the NuttShell (nsh) located at apps/examples/nsh. The
Configuration enables both the serial and telnet NSH interfaces.
CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows
CONFIG_NSH_DHCPC=n : DHCP is disabled
CONFIG_NSH_IPADDR=0x0a000002 : Target IP address 10.0.0.2
CONFIG_NSH_DRIPADDR=0x0a000001 : Host IP address 10.0.0.1
NOTES:
1. This example assumes that a network is connected. During its
initialization, it will try to negotiate the link speed. If you have
no network connected when you reset the board, there will be a long
delay (maybe 30 seconds?) before anything happens. That is the timeout
before the networking finally gives up and decides that no network is
available.
View Git Blame Copy Permalink