px4-firmware/nuttx/configs/pcblogic-pic32mx

configs/pic32mx README
=====================

This README file discusses the port of NuttX to the PIC32MX board from
PCB Logic Design Co.  This board features the MicroChip PIC32MX460F512L.
The board is a very simple -- little more than a carrier for the PIC32
MCU plus voltage regulation, debug interface, and an OTG connector.

Contents
========

  PIC32MX460F512L Pin Out
  MAX3232 Connection
  Toolchains
  Loading NuttX with PICkit2
  PIC32MX Configuration Options
  Configurations

PIC32MX460F512L Pin Out
=======================

  PIC32MX460F512L 100-Pin TQFP (USB) Pin Out.  The mapping to the pins on
  the PCL Logic board are very simple, each pin is brought out to a connector
  label with the PIC32MX460F512L pin number.

  On board logic only manages power, crystal, and USB signals.

  LEFT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left)
  PIN  NAME
  ---- ----------------------------
    1  RG15
    2  Vdd
    3  PMD5/RE5
    4  PMD6/RE6
    5  PMD7/RE7
    6  T2CK/RC1
    7  T3CK/RC2
    8  T4CK/RC3
    9  T5CK/SDI1/RC4
   10  SCK2/PMA5/CN8/RG6
   11  SDI2/PMA4/CN9/RG7
   12  SDO2/PMA3/CN10/RG8
   13  MCLR
   14  SS2/PMA2/CN11/RG9
   15  Vss
   16  Vdd
   17  TMS/RA0
   18  INT1/RE8
   19  INT2/RE9
   20  AN5/C1IN+/VBUSON/CN7/RB5
   21  AN4/C1IN-/CN6/RB4
   22  AN3/C2IN+/CN5/RB3
   23  AN2/C2IN-/CN4/RB2
   24  PGEC1/AN1/CN3/RB1
   25  PGED1/AN0/CN2/RB0

  BOTTOM SIDE, LEFT-TO-RIGHT (if pin 1 is in upper left)
  PIN  NAME
  ---- ----------------------------
   26  PGEC2/AN6/OCFA/RB6
   27  PGED2/AN7/RB7
   28  VREF-/CVREF-/PMA7/RA9
   29  VREF+/CVREF+/PMA6/RA10
   30  AVdd
   31  AVss
   32  AN8/C1OUT/RB8
   33  AN9/C2OUT/RB9
   34  AN10/CVREFOUT/PMA13/RB10
   35  AN11/PMA12/RB11
   36  Vss
   37  Vdd
   38  TCK/RA1
   39  U2RTS/RF13
   40  U2CTS/RF12
   41  AN12/PMA11/RB12
   42  AN13/PMA10/RB13
   43  AN14/PMALH/PMA1/RB14
   44  AN15/OCFB/PMALL/PMA0/CN12/RB15
   45  Vss
   46  Vdd
   47  U1CTS/CN20/RD14
   48  U1RTS/CN21/RD15
   49  U2RX/PMA9/CN17/RF4
   50  U2TX/PMA8/CN18/RF5

  RIGHT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left)
  PIN  NAME
  ---- ----------------------------
   75  Vss
   74  SOSCO/T1CK/CN0/RC14
   73  SOSCI/CN1/RC13
   72  SDO1/OC1/INT0/RD0
   71  IC4/PMCS1/PMA14/RD11
   70  SCK1/IC3/PMCS2/PMA15/RD10
   69  SS1/IC2/RD9
   68  RTCC/IC1/RD8
   67  SDA1/INT4/RA15
   66  SCL1/INT3/RA14
   65  Vss
   64  OSC2/CLKO/RC15
   63  OSC1/CLKI/RC12
   62  Vdd
   61  TDO/RA5
   60  TDI/RA4
   59  SDA2/RA3
   58  SCL2/RA2
   57  D+/RG2
   56  D-/RG3
   55  VUSB
   54  VBUS
   53  U1TX/RF8
   52  U1RX/RF2
   51  USBID/RF3

  TOP SIDE, LEFT-TO-RIGHT (if pin 1 is in upper left)
  PIN  NAME
  ---- ----------------------------
  100  PMD4/RE4
   99  PMD3/RE3
   98  PMD2/RE2
   97  TRD0/RG13
   96  TRD1/RG12
   95  TRD2/RG14
   94  PMD1/RE1
   93  PMD0/RE0
   92  TRD3/RA7
   91  TRCLK/RA6
   90  PMD8/RG0
   89  PMD9/RG1
   88  PMD10/RF1
   87  PMD11/RF0
   86  ENVREG
   85  Vcap/Vddcore
   84  PMD15/CN16/RD7
   83  PMD14/CN15/RD6
   82  PMRD/CN14/RD5
   81  OC5/PMWR/CN13/RD4
   80  PMD13/CN19/RD13
   79  IC5/PMD12/RD12
   78  OC4/RD3
   77  OC3/RD2
   76  OC2/RD1

 Additional Signals available from the board:

   PROGRAM CONNECTOR:  Vpp Vdd GND PGED1 PGEC1 NC PGED2 PGEC2
   POWER POINTS:       +5Vin +3.3V AVdd AGND Vdd GND USB+5V

MAX3232 Connection
==================

  I use a tiny, MAX3232 board that I got from the eBay made by NKC
  Electronics (http://www.nkcelectronics.com/).  As of this writing, it
  is also available here: http://www.nkcelectronics.com/rs232-to-ttl-3v--55v-convert232356.html

  CTS -- Not connected
  RTS -- Not connected
  TX  -- Pin 53: U1TX/RF8
  RX  -- Pin 52: U1RX/RF2
  GND -- POWER POINT: GND
  Vcc -- POWER POINT: Vdd (3.3V) -- Or P32_VBUS (+5V)
         -- Or +5V from a USB PC port.
 
Toolchains
==========

  I am using the free, LITE version of the PIC32MX toolchain available
  for download from the microchip.com web site.  I am using the Windows
  version.  The MicroChip toolchain is the only toolchaing currently
  supported in these configurations, but it should be a simple matter to
  adapt to other toolchains by modifying the Make.defs file include in
  each configuration.

  Toolchain Options:

  CONFIG_PIC32MX_MICROCHIPW      - MicroChip full toolchain for Windows
  CONFIG_PIC32MX_MICROCHIPL      - MicroChip full toolchain for Linux
  CONFIG_PIC32MX_MICROCHIPW_LITE - MicroChip LITE toolchain for Windows
  CONFIG_PIC32MX_MICROCHIPL_LITE - MicroChip LITE toolchain for Linux

  Windows Native Toolchains
  
  NOTE:  There are several limitations to using a Windows based toolchain in a
  Cygwin environment.  The three biggest are:

  1. The Windows toolchain cannot follow Cygwin paths.  Path conversions are
     performed automatically in the Cygwin makefiles using the 'cygpath' utility
     but you might easily find some new path problems.  If so, check out 'cygpath -w'

  2. Windows toolchains cannot follow Cygwin symbolic links.  Many symbolic links
     are used in Nuttx (e.g., include/arch).  The make system works around these
     problems for the Windows tools by copying directories instead of linking them.
     But this can also cause some confusion for you:  For example, you may edit
     a file in a "linked" directory and find that your changes had no effect.
     That is because you are building the copy of the file in the "fake" symbolic
     directory.  If you use a Windows toolchain, you should get in the habit of
     making like this:

       make clean_context all

     An alias in your .bashrc file might make that less painful.

  3. Dependencies are not made when using Windows versions of the GCC.  This is
     because the dependencies are generated using Windows pathes which do not
     work with the Cygwin make.

     Support has been added for making dependencies with the windows-native toolchains.
     That support can be enabled by modifying your Make.defs file as follows:

    -  MKDEP                = $(TOPDIR)/tools/mknulldeps.sh
    +  MKDEP                = $(TOPDIR)/tools/mkdeps.sh --winpaths "$(TOPDIR)"

     If you have problems with the dependency build (for example, if you are not
     building on C:), then you may need to modify tools/mkdeps.sh

Loading NuttX with PICkit2
==========================

  NOTE:  You need a PICKit3 if you plan to use the MPLAB debugger!  The PICKit2
  can, however, still be used to load programs.  Instructions for the PICKit3
  are similar.

  Intel Hex Forma Files:
  ----------------------

    When NuttX is built it will produce two files in the top-level NuttX
    directory:

    1) nuttx - This is an ELF file, and
    2) nuttx.ihx - This is an Intel Hex format file.  This is controlled by
       the setting CONFIG_INTELHEX_BINARY in the .config file.

    The PICkit tool wants an Intel Hex format file to burn into FLASH.
    However, there are two problems with the generated nutt.ihx:
  
    1) The tool expects Intel Hex format files to be named *.hex.  This
       is not a significant issue.  However, just renaming the file to
       nuttx.hex is *not* sufficient.  There is another problem:
    2) The tool expects the nuttx.hex file to contain physical addresses.
       But the nuttx.ihx file generated from the top-level make will have
       address in the KSEG0 and KSEG1 regions.

  tools/mkpichex:
  ---------------

    There is a simple tool in the configs/pcblogic-pic32mx/tools directory
    that can be used to solve both issues with the nuttx.ihx file.  But,
    first, you must build the the tools:

      cd configs/pcblogic-pic32mx/tools
      make

    Now you will have an excecutable file call mkpichex (or mkpichex.exe on
    Cygwin).  This program will take the nutt.ihx file as an input, it will
    convert all of the KSEG0 and KSEG1 addresses to physical address, and
    it will write the modified file as nuttx.hex.

    To use this file, you need to do the following things:

      . ./setenv.sh    # Source setenv.sh.  Among other this, this script
                       # will add configs/pcblogic-pic32mx/tools to your
                       # PATH variable
      make             # Build nuttx and nuttx.ihx
      mkpichex $PWD    # Convert nuttx.ihx to nuttx.hex.  $PWD is the path
                       # to the top-level build directory.  It is the only
                       # required input to mkpichex.

PIC32MX Configuration Options
=============================

  General Architecture Settings:

    CONFIG_ARCH - Identifies the arch/ subdirectory.  This should
     be set to:

       CONFIG_ARCH=mips

    CONFIG_ARCH_family - For use in C code:

       CONFIG_ARCH_MIPS=y

    CONFIG_ARCH_architecture - For use in C code:

       CONFIG_ARCH_MIPS32=y

    CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory

       CONFIG_ARCH_CHIP=pic32mx

    CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
       chip:

       CONFIG_ARCH_CHIP_PIC32MX460F512L=y

    CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
       hence, the board that supports the particular chip or SoC.

       CONFIG_ARCH_BOARD=pcblogic-pic32mx

    CONFIG_ARCH_BOARD_name - For use in C code

       CONFIG_ARCH_BOARD_PCBLOGICPIC32MX=y

    CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
       of delay loops

    CONFIG_ENDIAN_BIG - define if big endian (default is little
       endian)

    CONFIG_DRAM_SIZE - Describes the installed DRAM (CPU SRAM in this case):

       CONFIG_DRAM_SIZE=(32*1024) (32Kb)

       There is an additional 32Kb of SRAM in AHB SRAM banks 0 and 1.

    CONFIG_DRAM_START - The start address of installed DRAM

       CONFIG_DRAM_START=0x10000000

    CONFIG_DRAM_END - Last address+1 of installed RAM

       CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)

    CONFIG_ARCH_IRQPRIO - The PIC32MXx supports interrupt prioritization

       CONFIG_ARCH_IRQPRIO=y

    CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
       have LEDs

    CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
       stack. If defined, this symbol is the size of the interrupt
       stack in bytes.  If not defined, the user task stacks will be
       used during interrupt handling.

    CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions

    CONFIG_ARCH_LEDS -  Use LEDs to show state. Unique to board architecture.

    CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
       cause a 100 second delay during boot-up.  This 100 second delay
       serves no purpose other than it allows you to calibratre
       CONFIG_ARCH_LOOPSPERMSEC.  You simply use a stop watch to measure
       the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
       the delay actually is 100 seconds.

    PIC32MX Configuration

      CONFIG_PIC32MX_MVEC - Select muli- vs. single-vectored interrupts

    Individual subsystems can be enabled:

       CONFIG_PIC32MX_WDT            - Watchdog timer
       CONFIG_PIC32MX_T2             - Timer 2 (Timer 1 is the system time and always enabled)
       CONFIG_PIC32MX_T3             - Timer 3
       CONFIG_PIC32MX_T4             - Timer 4
       CONFIG_PIC32MX_T5             - Timer 5
       CONFIG_PIC32MX_IC1            - Input Capture 1
       CONFIG_PIC32MX_IC2            - Input Capture 2
       CONFIG_PIC32MX_IC3            - Input Capture 3
       CONFIG_PIC32MX_IC4            - Input Capture 4
       CONFIG_PIC32MX_IC5            - Input Capture 5
       CONFIG_PIC32MX_OC1            - Output Compare 1
       CONFIG_PIC32MX_OC2            - Output Compare 2
       CONFIG_PIC32MX_OC3            - Output Compare 3
       CONFIG_PIC32MX_OC4            - Output Compare 4
       CONFIG_PIC32MX_OC5            - Output Compare 5
       CONFIG_PIC32MX_I2C1           - I2C 1
       CONFIG_PIC32MX_I2C2           - I2C 2
       CONFIG_PIC32MX_SPI1           - SPI 1
       CONFIG_PIC32MX_SPI2           - SPI 2
       CONFIG_PIC32MX_UART1          - UART 1
       CONFIG_PIC32MX_UART2          - UART 2
       CONFIG_PIC32MX_ADC            - ADC 1
       CONFIG_PIC32MX_PMP            - Parallel Master Port
       CONFIG_PIC32MX_CM1            - Comparator 1
       CONFIG_PIC32MX_CM2            - Comparator 2
       CONFIG_PIC32MX_RTCC           - Real-Time Clock and Calendar
       CONFIG_PIC32MX_DMA            - DMA
       CONFIG_PIC32MX_FLASH          - FLASH
       CONFIG_PIC32MX_USBDEV         - USB device
       CONFIG_PIC32MX_USBHOST        - USB host

    PIC32MX Configuration Settings
    DEVCFG0:
      CONFIG_PIC32MX_DEBUGGER - Background Debugger Enable. Default 3 (disabled). The
        value 2 enables.
      CONFIG_PIC32MX_ICESEL - In-Circuit Emulator/Debugger Communication Channel Select
        Default 1 (PG2)
      CONFIG_PIC32MX_PROGFLASHWP  - Program FLASH write protect.  Default 0xff (disabled)
      CONFIG_PIC32MX_BOOTFLASHWP - Default 1 (disabled)
      CONFIG_PIC32MX_CODEWP - Default 1 (disabled)
    DEVCFG1: (All settings determined by selections in board.h)
    DEVCFG2: (All settings determined by selections in board.h)
    DEVCFG3: 
      CONFIG_PIC32MX_USBIDO - USB USBID Selection.  Default 1 if USB enabled
        (USBID pin is controlled by the USB module), but 0 (GPIO) otherwise.
      CONFIG_PIC32MX_VBUSIO - USB VBUSON Selection (Default 1 if USB enabled
        (VBUSON pin is controlled by the USB module, but 0 (GPIO) otherwise.
      CONFIG_PIC32MX_WDENABLE - Enabled watchdog on power up.  Default 0 (watchdog
        can be enabled later by software).

    The priority of interrupts may be specified.  The value ranage of
    priority is 4-31. The default (16) will be used if these any of these
    are undefined.

       CONFIG_PIC32MX_CTPRIO         - Core Timer Interrupt
       CONFIG_PIC32MX_CS0PRIO        - Core Software Interrupt 0
       CONFIG_PIC32MX_CS1PRIO        - Core Software Interrupt 1
       CONFIG_PIC32MX_INT0PRIO       - External Interrupt 0
       CONFIG_PIC32MX_INT1PRIO       - External Interrupt 1
       CONFIG_PIC32MX_INT2PRIO       - External Interrupt 2
       CONFIG_PIC32MX_INT3PRIO       - External Interrupt 3
       CONFIG_PIC32MX_INT4PRIO       - External Interrupt 4
       CONFIG_PIC32MX_FSCMPRIO       - Fail-Safe Clock Monitor
       CONFIG_PIC32MX_T1PRIO         - Timer 1 (System timer) priority
       CONFIG_PIC32MX_T2PRIO         - Timer 2 priority
       CONFIG_PIC32MX_T3PRIO         - Timer 3 priority
       CONFIG_PIC32MX_T4PRIO         - Timer 4 priority
       CONFIG_PIC32MX_T5PRIO         - Timer 5 priority
       CONFIG_PIC32MX_IC1PRIO        - Input Capture 1
       CONFIG_PIC32MX_IC2PRIO        - Input Capture 2
       CONFIG_PIC32MX_IC3PRIO        - Input Capture 3
       CONFIG_PIC32MX_IC4PRIO        - Input Capture 4
       CONFIG_PIC32MX_IC5PRIO        - Input Capture 5
       CONFIG_PIC32MX_OC1PRIO        - Output Compare 1
       CONFIG_PIC32MX_OC2PRIO        - Output Compare 2
       CONFIG_PIC32MX_OC3PRIO        - Output Compare 3
       CONFIG_PIC32MX_OC4PRIO        - Output Compare 4
       CONFIG_PIC32MX_OC5PRIO        - Output Compare 5
       CONFIG_PIC32MX_I2C1PRIO       - I2C 1
       CONFIG_PIC32MX_I2C2PRIO       - I2C 2
       CONFIG_PIC32MX_SPI1PRIO       - SPI 1
       CONFIG_PIC32MX_SPI2PRIO       - SPI 2
       CONFIG_PIC32MX_UART1PRIO      - UART 1
       CONFIG_PIC32MX_UART2PRIO      - UART 2
       CONFIG_PIC32MX_CN             - Input Change Interrupt
       CONFIG_PIC32MX_ADCPRIO        - ADC1 Convert Done
       CONFIG_PIC32MX_PMPPRIO        - Parallel Master Port
       CONFIG_PIC32MX_CM1PRIO        - Comparator 1
       CONFIG_PIC32MX_CM2PRIO        - Comparator 2
       CONFIG_PIC32MX_FSCMPRIO       - Fail-Safe Clock Monitor
       CONFIG_PIC32MX_RTCCPRIO       - Real-Time Clock and Calendar
       CONFIG_PIC32MX_DMA0PRIO       - DMA Channel 0
       CONFIG_PIC32MX_DMA1PRIO       - DMA Channel 1
       CONFIG_PIC32MX_DMA2PRIO       - DMA Channel 2
       CONFIG_PIC32MX_DMA3PRIO       - DMA Channel 3
       CONFIG_PIC32MX_FCEPRIO        - Flash Control Event
       CONFIG_PIC32MX_USBPRIO        - USB

  PIC32MXx specific device driver settings

    CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
       console and ttys0 (default is the UART0).
    CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
       This specific the size of the receive buffer
    CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
       being sent.  This specific the size of the transmit buffer
    CONFIG_UARTn_BAUD - The configure BAUD of the UART.  Must be
    CONFIG_UARTn_BITS - The number of bits.  Must be either 7 or 8.
    CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
    CONFIG_UARTn_2STOP - Two stop bits

  PIC32MXx USB Device Configuration

  PIC32MXx USB Host Configuration (the PIC32MX does not support USB Host)

Configurations
==============

Each PIC32MX configuration is maintained in a sudirectory and can be
selected as follow:

    cd tools
    ./configure.sh pcblogic-pic32mx/<subdir>
    cd -
    . ./setenv.sh

Where <subdir> is one of the following:

  ostest:
    This configuration directory, performs a simple OS test using
    apps/examples/ostest.