px4-firmware/msg/BatteryStatus.msg

79 lines
5.0 KiB
Plaintext
Raw Permalink Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

uint64 timestamp # time since system start (microseconds)
bool connected # Whether or not a battery is connected, based on a voltage threshold
float32 voltage_v # Battery voltage in volts, 0 if unknown
float32 voltage_filtered_v # Battery voltage in volts, filtered, 0 if unknown
float32 current_a # Battery current in amperes, -1 if unknown
float32 current_filtered_a # Battery current in amperes, filtered, 0 if unknown
float32 current_average_a # Battery current average in amperes, -1 if unknown
float32 discharged_mah # Discharged amount in mAh, -1 if unknown
float32 remaining # From 1 to 0, -1 if unknown
float32 scale # Power scaling factor, >= 1, or -1 if unknown
float32 time_remaining_s # predicted time in seconds remaining until battery is empty under previous averaged load, NAN if unknown
float32 temperature # temperature of the battery. NaN if unknown
uint8 cell_count # Number of cells, 0 if unknown
uint8 BATTERY_SOURCE_POWER_MODULE = 0
uint8 BATTERY_SOURCE_EXTERNAL = 1
uint8 BATTERY_SOURCE_ESCS = 2
uint8 source # Battery source
uint8 priority # Zero based priority is the connection on the Power Controller V1..Vn AKA BrickN-1
uint16 capacity # actual capacity of the battery
uint16 cycle_count # number of discharge cycles the battery has experienced
uint16 average_time_to_empty # predicted remaining battery capacity based on the average rate of discharge in min
uint16 serial_number # serial number of the battery pack
uint16 manufacture_date # manufacture date, part of serial number of the battery pack. Formatted as: Day + Month×32 + (Year1980)×512
uint16 state_of_health # state of health. FullChargeCapacity/DesignCapacity, 0-100%.
uint16 max_error # max error, expected margin of error in % in the state-of-charge calculation with a range of 1 to 100%
uint8 id # ID number of a battery. Should be unique and consistent for the lifetime of a vehicle. 1-indexed.
uint16 interface_error # interface error counter
float32[14] voltage_cell_v # Battery individual cell voltages, 0 if unknown
float32 max_cell_voltage_delta # Max difference between individual cell voltages
bool is_powering_off # Power off event imminent indication, false if unknown
bool is_required # Set if the battery is explicitly required before arming
uint8 BATTERY_WARNING_NONE = 0 # no battery low voltage warning active
uint8 BATTERY_WARNING_LOW = 1 # warning of low voltage
uint8 BATTERY_WARNING_CRITICAL = 2 # critical voltage, return / abort immediately
uint8 BATTERY_WARNING_EMERGENCY = 3 # immediate landing required
uint8 BATTERY_WARNING_FAILED = 4 # the battery has failed completely
uint8 BATTERY_STATE_UNHEALTHY = 6 # Battery is diagnosed to be defective or an error occurred, usage is discouraged / prohibited. Possible causes (faults) are listed in faults field.
uint8 BATTERY_STATE_CHARGING = 7 # Battery is charging
uint8 BATTERY_FAULT_DEEP_DISCHARGE = 0 # Battery has deep discharged
uint8 BATTERY_FAULT_SPIKES = 1 # Voltage spikes
uint8 BATTERY_FAULT_CELL_FAIL= 2 # One or more cells have failed
uint8 BATTERY_FAULT_OVER_CURRENT = 3 # Over-current
uint8 BATTERY_FAULT_OVER_TEMPERATURE = 4 # Over-temperature
uint8 BATTERY_FAULT_UNDER_TEMPERATURE = 5 # Under-temperature fault
uint8 BATTERY_FAULT_INCOMPATIBLE_VOLTAGE = 6 # Vehicle voltage is not compatible with battery one
uint8 BATTERY_FAULT_INCOMPATIBLE_FIRMWARE = 7 # Battery firmware is not compatible with current autopilot firmware
uint8 BATTERY_FAULT_INCOMPATIBLE_MODEL = 8 # Battery model is not supported by the system
uint8 BATTERY_FAULT_HARDWARE_FAILURE = 9 # hardware problem
uint8 BATTERY_WARNING_OVER_TEMPERATURE = 10 # Over-temperature
uint8 BATTERY_FAULT_COUNT = 11 # Counter - keep it as last element!
uint16 faults # Smart battery supply status/fault flags (bitmask) for health indication.
uint32 custom_faults # Bitmask indicating smart battery internal manufacturer faults, those are not user actionable.
uint8 warning # Current battery warning
uint8 mode # Battery mode. Note, the normal operation mode
uint8 BATTERY_MODE_UNKNOWN = 0 # Battery does not support a mode, or if it does, is operational
uint8 BATTERY_MODE_AUTO_DISCHARGING = 1 # Battery is auto discharging (towards storage level)
uint8 BATTERY_MODE_HOT_SWAP = 2 # Battery in hot-swap mode
uint8 BATTERY_MODE_COUNT = 3 # Counter - keep it as last element (once we're fully migrated to events interface we can just comment this)!
uint8 MAX_INSTANCES = 4
float32 average_power # The average power of the current discharge
float32 available_energy # The predicted charge or energy remaining in the battery
float32 full_charge_capacity_wh # The compensated battery capacity
float32 remaining_capacity_wh # The compensated battery capacity remaining
float32 design_capacity # The design capacity of the battery
uint16 average_time_to_full # The predicted remaining time until the battery reaches full charge, in minutes
uint16 over_discharge_count # Number of battery overdischarge
float32 nominal_voltage # Nominal voltage of the battery pack