nxp/rt117x:Fix Pin IRQ
nxp/rt117x:Support 4 i2c busses
nxp/rt117x:Add px4io_serial support
nxp/imxrt:Expand ToneAlarmInterface to GPT 3 & 4
px4_fmu-6xrt:Using imxrt_flexspi_nor_octal
px4_fmu-6xrt:Entry is start
px4_fmu-6xrt:Add Proper MTD
px4_fmu-6xrt:Set I2C Buses
px4_fmu-6xrt:Proper SPI usage
px4_fmu-6xrt:Adjust memory Map to use the 2 MB
px4_fmu-6xrt:Bring in ROMAPI
px4_fmu-6xrt:Push FLASH to 200Mhz
px4_fmu-6xrt:Use BOARD_I2C_LATEINIT
px4_fmu-6xrt:Clock Config remove unused devices
px4_fmu-6xrt:Remove EVK SDRAM IO
px4_fmu-6xrt:Enable SE550 using HW_VER_REV_DRIVE
px4_fmu-6xrt:Use MTD to mount FRAM on Flex SPI
px4_fmu-6xrt:Manifest
px4_fmu-6xrt:Restore board_peripheral_reset
px4_fmu-6xrt:Set I2C buss Interna/Externa and startup
nxp/rt117x:Set 6 I2C busses
px4_fmu-6xrt:Correct Clock Sources and Freqency Settings
px4_fmu-6xrt:Correct ADC Settings
px4_fmu-6xrt:Tune FlexSPI config and sync header with debug variant Linker prep for rodata ahb partitioning
px4_fmu-6xrt:FlexSPI prefetch partition split .text and .rodata
Current config
1KB Prefetch .rodata
3KB Prefetch .text
px4_fmu-6xrt:Run imxrt_flash_setup_prefetch_partition from ram with barriers
px4_fmu-6xrt:Use All OCTL setting from FLASH g_flash_config SANS lookupTable
px4_fmu-6xrt:Octal spi boot/debug problem bypass
px4_fmu-6xrt:Add PWM test
px4_fmu-6xrt:Fix clockconfig and USB vbus sense
px4_fmu-6xrt: Use TCM
px4_fmu-6xrt: Ethernet bringup
imxrt: use unique_id register for board_identity
px4_fmu-6xrt: update ITCM mapping, todo proper trap on pc hitting 0x0
px4_fmu-6xrt:correct rotation icm42688p onboard imu
rt117x: Add SSARC HP RAM driver for memory dumps
px4_fmu-6xrt: Enable hardfault_log
px4_fmu-6xrt: Enable DMA pool
px4_fmu-6xrt: fix uart mapping
px4_fmu-6xrt: enable SocketCAN & DroneCAN
px4_fmu-6xrt:Command line history TAB completion
px4_fmu-6xrt:Fix pinning duplication
px4_fmu-6xrt:Support conditional PHY address based on selected PHY
px4_fmu-6xrt:Add Pull Downs on CTS, use GPIO for RTS
px4_fmu-6xrt:Set TelemN TX Slew rate and Drive Strenth to max
px4_fmu-6xrt::Set TELEM Buffers add HW HS
px4_fmu-6xrt:Turn off DMA poll
px4_fmu-6xrt:RC_SERIAL_PORT needed to be px4io to disable rc_input using TELEM2!
px4_fmu-6xrt: bootloader (#22228)
* imxrt:Add bootloader support
* bootloader:imxrt clear BOOT_RTC_SIGNATURE
* px4_fmu-6xrt:Add bootloader
* px4_fmu-6xrt:bootloader removed ADC
* px4_fmu-6xrt:bootloader base bootloader script off of script.ld
* px4_fmu-6xrt:add _bootdelay_signature & change entry from 0x30000000 to 0x30040000
* px4_fmu-6xrt:hw_config Bootloader has to have 12 bytes
px4_fmu-6xrt:Default to use LAN8742A PHY
px4_fmu-v6xrt:VID Set to Drone Code
board_reset:Enable ability to write RTC GP regs
px4_fmu-6xrt:Fix CMP0079 error
rt117x:micro_hal Add a PX4_MAKE_GPIO_PULLED_INPUT
px4_fmu-v6xrt:Set CTS High before VDD_5V applided to ports to avoid radios fro entering bootloaders
fmu-v6xrt: increase 5v down time
fmu-v6xrt:Ready for Release DEBUGASSERTS off and Console 57600,
Bootloder updated.
imxrt:board_hw_rev_ver Rework for 3.893V Ref
px4_fmu-v6xrt:Move ADC to Port3
imxrt:117x Reuse all but io_timer_hw_description and imxrt_pinirq.c
imxrt:ADC & LPADC bifurcation and restructuring
imxrt:hrt support Up to GPT6
nxp/rt117x:adc Corrected
The param is not really required anymore with the actuator
configuration. Also, when it is set to 0, RC doesn't work for some
boards which would be nice to avoid.
Signed-off-by: Julian Oes <julian@oes.ch>
This allows to inject an updated ext_autostart folder with the name
ext_autostart_new, and then PX4 takes care of renaming it to
ext_autostart during bootup.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- for FW the primary range finder usage is estimating the distance to
the ground (terrain estimate) to guide the landing approach and initiate flare
- increase EKF2_RNG_QLTY_T default 1->3 seconds
* added a new driver ASP5033 for measuring the differential pressure and airspeed
---------
Co-authored-by: nano <nanobotzhe@abv.bg>
Co-authored-by: Denislav Petrov <you@example.com>
This adds support for the TI LP5562 RGB LED driver.
Things to note:
- The driver is initialized in simple PWM mode using its internal clock,
for R,G,B, but not for W(hite).
- The chip doesn't have a WHO_AM_I or DEVICE_ID register to check.
Instead we read the W_CURRENT register that we're generally not using
and therefore doesn't get changed.
- The current is left at the default 17.5 mA but could be changed using
the command line argument.
Datasheet:
https://www.ti.com/lit/ds/symlink/lp5562.pdf
Signed-off-by: Julian Oes <julian@oes.ch>
5s is a more reasobale time for tailsitters, which rely differently on this param
than other VTOL types. Tailsitters will ramp the pitch up withing this time,
while for other VTOLS types its only the max transitiont time.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
A default of 10s makes more sense compared to the old 4s, as this is only the
max time of a back transition and it's also decleared completed if the
speed drops below the hover cruising speed (MPC_XY_CRUISE).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
There have been substantial TECS changes lately, and the config files
for custom VTOLs have not been updated since a long time. I would thus
rather use the default TECS gains for lightly maintained configs.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
bresch
Daniel Agar
Matthias Grob
David Sidrane
Igor Mišić
PerFrivik
Silvan Fuhrer
Konrad
PerFrivik
Julian Oes
Peter van der Perk
Vincent Poon
Denislav Petrov
Beat Küng
alexklimaj
Thomas Stastny
Beniamino Pozzan