- add command to request a message
- add gimbal attitude message
mavlink_receiver handle GIMBAL_MANAGER_SET_ATTITUDE
first implementation of new vmount input MavlinkGimbalV2
- setup class
- decode gimbal_manager_set_attitude in ControlData
add gimbal information message
add gimbal manager information and vehicle command ack
mavlink messages: add stream for GIMBAL_MANAGER_INFORMATION
mavlink_receiver: handle GIMBAL_DEVICE_INFORMATION
remove mavlink cmd handling from vmount input MavlinkGimbalV2
complete gimbal manager:
- send out fake gimbal_device_information for dummy gimbals
- complete ROI handling with nudging
small fixes
fix typos
cleanup
- gimbal device information
- flags lock
- check sanity of string
add support for CMD_DO_GIMBAL_MANAGER_ATTITUDE
stream GimbalDeviceAttitudeStatus for dummy gimbals
- add uROB gimbal_attitude_status
- fill status in vmount output_rc for dummy gimbals not able to send the
status themselves
- stream mavlink GimbalDeviceAttitudeStatus
better handle the request for gimbal infomation request
clean up
bring gimbal information back on vmount init
add new gimbal message to mavlink normal stream
fix publication of gimbal device information
rename gimbal_attitude_status to gimbal_device_attitude_status
stream gimbal_manager_status at 5Hz
mavlink: send information only on request
Sending the information message once on request should now work and we
don't need to keep publishing it.
mavlink: debug output for now
make sure to copy over control data
mavlink: add missing copyright header, pragma once
mavlink: address review comments
mavlink: handle stream not updated
Our answer does not just depend on whether the stream was found but
whether we actually were able to send out an update.
mavlink: remove outdated comment
vmount: add option for yaw stabilization only
The stabilize flag is used for gimbals which do not have an internal IMU
and need the autopilot's attitude in order to do stabilization. These
gimbals are probably quite rare by now but it makes sense to keep the
functionality given it can e.g. be used by simple servo gimbals for
sensors other than highres cameras.
The stabilize flag can also be re-used for gimbals which are capable of
stabilizing pitch and roll but not absolute yaw (e.g. locked to North).
For such gimbals we can now set the param MNT_DO_STAB to 2.
We still support configuring which axes are stabilized by the
MAVLink command DO_MOUNT_CONFIGURE, however, this is generally not
recommended anymore.
vmount: fix incorrect check for bit flag
mavlink_messages: remove debug message
Signed-off-by: Claudio Micheli <claudio@auterion.com>
use device id
remove debug print
gimbal attitude fix mistake
clang tidy fix
split:
- gimbal_attitude -> gimbal_device_set_attitude, gimbal_manager_set_attitude
- gimbal_information -> gimbal_device_informatio, gimbal_manager_information
add gimbal protocol messages to rtps msg ids
support set attitude for gimbal directly speaking mavlink
clean up gimbal urob messages
vmount: address a few small review comments
vmount: split output into v1 and v2 protocol
This way we can continue to support the MAVLink v1 protocol. Also, we
don't send the old vehicle commands when actually using the new v2
protocol.
vmount: config via ctor instead of duplicate param
vmount: use loop to poll all topics
Otherwise we might give up too soon and miss some data, or run too fast
based on commands that have nothing to do with the gimbal.
typhoon_h480: use gimbal v2 protocol, use yaw stab
Let's by default use the v2 protocol with typhoon_h480 and enable yaw
lock mode by stabilizing yaw.
- use proper Mavlink MAV_CMD_FIXED_MAG_CAL_YAW command for initiating magnetometer quick cal
- MAV_CMD_FIXED_MAG_CAL_YAW allows specifying the yaw and optionally latitude and longitude if the vehicle doesn't have GPS
Allow enabling/disabling transmitting data from all mavlink instances
with a specific mode/type. When disabled the instance can still receive
data. The uORB message used is the vehicle_command and uses the following
parameter:
param1: Specifies the mode/type of the instances to enable/disable transmitting
param2: Boolean to indicate if transmitting should be enabled or disabled
The previous approach was checking system id and component id but it
will not work in 100% of cases as external devices can send MAVLink
message with the right system id but with broadcast component id.
MavLink spec implementation
implemented vehicle_roi topic
rename old gimbal to rc_gimbal
little changes
corrected RC Gimbal group
Starting ROI implementation in commander
implementation done, needs to be tested
uhm..
add todo
Change to float32 for x,y and z
remove mission topic again, not needed
change roi coordinates to lat, lon and alt
adjust to float64
starting mount implementation
correcting small mistakes, compiles now
add todos
further progress
implementing parameters
adjust default parameters
started implementation of mavlink
fix typo
change to lat, lon and alt
fix typo :D
change to double (to represent float64)
add global_position_
add mount topic
commander mount implementation done
cleanup
almost finished
little fix
codestyle fixes
leave pitch at 0 degrees
added pitch calculation
codestyle changes
Undo vehicle_mount, react to updated parameters, parsing of CMD_DO_MOUNT_* in mount.cpp
start implementing mode override
forgot a semikolon.
add debug
Finish implementation of mount override and manual control.
fix codestyle
correct cleanup
rename to vmount
works now
fix rebase error
fix polling
refactoring and custom airframe for gimbal
couple changes
remove warnx
almost done
finally
What is going on?
change back to actuator_controls_2
working
bump parameter version number and some clarification
fix submodules
Julian Oes
Martina Rivizzigno
Daniel Agar
Igor Campos
FengShun
David Jablonski
Lorenz Meier
Beat Küng
TSC21
MaEtUgR
acfloria
DonLakeFlyer
Nicolas de Palezieux
José Roberto de Souza
Mohammed Kabir
Don Gagne
David Sidrane
Leon
sander
Lorenz Meier
Andreas Antener
Mohammed Kabir