This is needed for DMA capable memory for fat also in the user side;
the file system doesn't seem to work reliably without.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
For protected/kernel builds the cxx static initializations
needs to be done also in kernel side, since px4 creates
c++ objects in kernel
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Implement an interface for protected build to access parameters.
The implementation only does IOCTL calls to the kernel, where the parameters
live.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This adds a nuttx userspace interface for hrt driver, communicating with
the actual px4 hrt driver via BOARDCTL IOCTLs
This is be used when running PX4 in NuttX protected or kernel builds
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Move some logic from Subscriber into uORBManager. This reduces calls from the
modules to the uORB manager, improving performance in protected build.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
* Adds Timer15 to stm32_common, if the timer base is defined
* Adds Timer15 logic for DMA and AltFunc config on stm32h7 boards
* Adds TIM15 BDTR->MOE support in stm32_common timer init
* Adds support for TIM15 pwm channels on Matek H743 Slim
If the hardware support RESET lockout that has nArmed ANDed with VBUS
vbus_sense may drop during a param save which uses
BOARD_INDICATE_EXTERNAL_LOCKOUT_STATE to prevent external resets
while writing the params. If we are not armed and nARMRED is low
we are in such a lock out so ignore changes on VBUS_SENSE during this
time.
It was a mistake to mix these two together, it is simpler to implement the boardctl interface
for the protected build, if the boardctl ioctls are different
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This adds an ioctl interface for NuttX protected build, allowing
system calls from user space to kernel for uORB, HRT and crypto
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
When building uORB for NuttX flat build, or for some other target, everything
works as before.
When building uORB for NuttX protected or kernel build, this does the following:
- The kernel side uORB library reigsters a boardctl handler for calls from userspace
and services the boardctl_ioctls by calling the actual uORB functions
- For user mode binaries, the uORBManager acts as a proxy, making boardctl_ioctl calls to the
kernel side
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This is the case for boards with digital readout, like v5x, but still
enable the battery_status module for external analog driver options.
An alternative would be to not run battery_status depending on config.
SD is on SPI3 - correct pin mapping
Fix DMA Mapping for all SPI and RX DMA on U[S]ART RX
Fix Memory MAP SRAM size
Removed unused GPIO
Used proper I2C definitions
Ensure Watchdog is configured for debugging
Fixed FLASH param definitions
Removed unedded SPI init
matek_gnss-m9n-f4:Correct Board ID and Size
Build order SJF
Added Support for F40x
Split the px4_layer into user and kernel space libraries. Add some stubs for
user-space (e.g. version) where an interface to the kernel needs to be added
Use posix-versions for cpuload.cpp and print_load.cpp for userspace; these link to nuttx internals. This functinality could be built on top of posix (e.g. procfs) interfaces
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Daniel Agar
David Sidrane
CUAVmengxiao
Jacob Schloss
Thomas Debrunner
Jukka Laitinen
wangwwno1
Charles Cross
Beat Küng
Peter van der Perk