dark0707
/
px4-firmware
forked from Archive/PX4-Autopilot
1
0
Fork 0
Code Pull Requests Activity
40,151 Commits 514 Branches 136 Tags 234 MiB
Commit Graph

134 Commits

Author SHA1 Message Date
alessandro 0617fd2b6f fmu-v6x: increase UART5 buffer size 
The same fix had to be done for the fmu-v5x:
PX4/PX4-Autopilot#14932
 2022-03-09 08:39:34 -05:00
David Sidrane c0facec889 cdc_acm_check:Prevent USB disconect on param save 
If the hardware support RESET lockout that has nArmed ANDed with VBUS
   vbus_sense may drop during a param save which uses
   BOARD_INDICATE_EXTERNAL_LOCKOUT_STATE to prevent external resets
   while writing the params.  If we are not armed and nARMRED is low
   we are in such a lock out so ignore changes on VBUS_SENSE during this
   time.
 2022-02-21 10:56:41 +01:00
David Sidrane 92590155fc px4_fmu-v6x:Bootloader move to TELEM1 with DMA 2022-02-16 10:09:02 -05:00
David Sidrane b5916ac712 px4_fmu-v6x:Document the DMA usage 2022-02-16 10:09:02 -05:00
David Sidrane 7eefdd1e3d px4_fmu-v6x:Enable DMA on TELEM{1|2} 2022-02-16 10:09:02 -05:00
Julian Oes 490a0c473b Rename vmount to gimbal 2022-02-07 19:21:15 -05:00
Beat Küng 92769bd2b2 dshot: remove BOARD_DSHOT_MOTOR_ASSIGNMENT & handle timer channel gaps 2022-01-21 20:41:15 -05:00
Daniel Agar daa925137c boards: move default battery calibration defines to parameter defaults 2022-01-10 09:49:36 -05:00
Julian Oes 9686c81f7d boards: enable flow control on CDCACM 
This enables flow control on CDCACM for the NuttX boards which fixes a
problem where HITL would stall.

The stall could happen if the hardware would be a bit too slow in
keeping up with the incoming messages. Often, this happened on arming
because the logger would take some time to log all parameters right at
the beginning.

The stall would then not recover due to NuttX bug where the rx interrupt
would not be restored correctly and instead only a slower watchdog would
release the next read. This watchdog takes 200ms which means it's hard
to impossible to get out of the situation without restarting sim and/or
PX4.  For more information about the issue, see:
apache/incubator-nuttx#3633

As a workaround, until that bug is fixed, and because it makes sense
anyway, I propose to enable FLOWCONTROL for the serial via USB.
 2021-12-21 08:01:38 +01:00
Daniel Agar 8185e2a384 boards: board_app_initialize() don't return early on failure 
- depending on the situation we're more likely to get actionable user
feedback by allowing boot to complete rather than silently failing
 2021-12-09 20:41:54 -05:00
Daniel Agar a2064cceff boards: enable early MPU reset on any board potentially not using the PX4 bootloader 2021-12-01 20:13:41 -05:00
Daniel Agar 9b7c8c8a8b boards: px4_fmu-v6x_default enable ethernet by default with NuttX optimizations 2021-11-29 09:08:42 -05:00
David Sidrane 23c73d4e0b px4_fmu-v6x nsh:Remove CONFIG_RAMTRON_WRITEWAIT 2021-11-26 19:27:29 -05:00
David Sidrane c391d6793c px4_fmu-v6x:Set CONFIG_MKFATFS_BUFFER_ALIGMENT=32 2021-11-24 09:46:23 -05:00
Beat Küng 4c03def6e9 boards: add CONTROL_ALLOCATOR + ACTUATOR_TEST 2021-11-23 12:40:22 -05:00
Daniel Agar f5d9b01f5c
NuttX build in place 
- cmake NuttX build wrapper compile in place instead of copying source tree to build directory
    - slightly faster skipping necessary copying (depending on system)
    - allows debugging in place
    - easier to work directly in NuttX following official documentation
    - simplifies overall build which should make it easier to resolve any remaining NuttX dependency issues in the build system
 - the downside is switching back and forth between different builds always require rebuilding NuttX, but I think this is worth the improved developer experience
 - also no longer builds px4io and bootloader in every single build, for most users these rarely change and we're wasting a lot of build time
 2021-11-15 18:47:38 -05:00
Daniel Agar 2d816e0b3e [WIP] manual_control selector hacks 2021-11-09 16:05:25 +01:00
Daniel Agar a8c3bcca32 boards: disable CONFIG_STM32H7_SPI_DMATHRESHOLD 2021-11-08 19:20:47 -05:00
bresch 6ec9ab11f2 add fw auto-tune module to board configs 2021-10-25 13:41:31 +02:00
Daniel Agar 2ed623c8ae boards: px4_fmu-v6x_default disable modules to save flash 2021-10-18 18:45:19 -04:00
Beat Küng 2b039b2af8 px4/fmu-v6x: add capture pins to list of pwm pins 2021-10-18 18:45:19 -04:00
Daniel Agar cb6b1bd427 boards: delete unused test and debug variants 2021-10-07 10:09:01 -04:00
Peter van der Perk 05d71c8118 Kconfig fix CI issues after rebase 2021-10-07 10:09:01 -04:00
Peter van der Perk ed5fee1a72 Backport #18311 mc atune 2021-10-07 10:09:01 -04:00
Peter van der Perk 454c907b7d Kconfig backport #18327 mag_bias 2021-10-07 10:09:01 -04:00
Peter van der Perk 36191e649a Kconfig backport #18289 and other flash size fixes 2021-10-07 10:09:01 -04:00
Peter van der Perk 5e98f38f78 Kconfig rebase backports 26-09-21 2021-10-07 10:09:01 -04:00
Peter van der Perk 6a1675ac28 Backport #17864 to px4board config 2021-10-07 10:09:01 -04:00
Peter van der Perk 12898ea560 [Kconfig] Update configs 06-09-21 2021-10-07 10:09:01 -04:00
Peter van der Perk 0571932e7c [Kconfig] Backport rebase config changes 2021-10-07 10:09:01 -04:00
Peter van der Perk 33fd65e5fe [Kconfig] Fix regressions found by bloaty and cleanup unused cmake 2021-10-07 10:09:01 -04:00
Peter van der Perk 43a3de8c18 [Kconfig] Fix px4 fmu configs 2021-10-07 10:09:01 -04:00
Peter van der Perk efc91d2b69 [Kconfig] Fixed inclusion of microbench bydefault when TESTING was enabled 
Added full optimization option
 2021-10-07 10:09:01 -04:00
Peter van der Perk a1247d6bcf [Kconfig] Backport cmake config changes 2021-10-07 10:09:01 -04:00
Peter van der Perk b3e799e277 [Kconfig] Add all distance sensors 2021-10-07 10:09:01 -04:00
Peter van der Perk 21e6547ac7 [Kconfig] Toolchain & platform fixes, SITL still broken 2021-10-07 10:09:01 -04:00
Peter van der Perk 6af0477733 [Kconfig] Gnerate px4board from old cmake 
Added make updateconfig to update all config when default's have changed
Added cmake to px4board conversion script
 2021-10-07 10:09:01 -04:00
Daniel Agar bbfaa4694c
boards: cleanup serial RX DMA hrt_call_every 
- remove ts_to_abstime dependency
 2021-10-06 14:39:59 -04:00
Daniel Agar 51758bd7e6
boards: delete unused variants 2021-10-05 23:14:04 -04:00
Daniel Agar 02aed782e3
boards: px4_fmu-v6x_default disable sd_stress to save flash 2021-10-05 18:17:22 -04:00
Daniel Agar b4d33a36f8
boards: px4_fmu-v6x_default disable examples/fake_gps to save flash 2021-10-05 17:11:47 -04:00
Daniel Agar c271a9e3e6 add sd_stress to all boards and run on test rack 2021-10-04 17:38:31 -04:00
Daniel Agar 6d78054f50
mavlink USB auto start/stop on boards with VBUS 
- no longer start sercon or mavlink usb by default
 - on USB connection (VBUS) monitor serial USB at low rate and start Mavlink if there's a HEARTBEAT or nshterm on 3 consecutive carriage returns
 - the mavlink USB instance is automatically stopped and serdis executed if USB is disconnected
 - skipping Mavlink USB (and sercon) saves a considerable amount of memory on older boards
 2021-10-03 15:32:54 -04:00
bresch 1443f773da mbe: add module to targets 2021-10-02 21:25:21 -04:00
bresch 5874b1f87c mc atune: add module to all targets 
- adjust flash constrianed targets to fit
 2021-10-02 18:12:05 -04:00
Thomas Debrunner 43ece74fa0 ina238: Do not expose raw adc config to user, make specific to ina238 2021-09-22 10:02:17 +02:00
Thomas Debrunner b8d0bb44c4 ina23X: Support for ina23X power monitors 2021-09-22 10:02:17 +02:00
Beat Küng 946857ddf7 px4/fmu-v6x: disable modules to reduce flash 2021-09-11 14:08:41 -04:00
Beat Küng c5c80e31b6 boards: remove DIRECT_INPUT_TIMER_CHANNELS from board_config.h 2021-09-08 16:10:24 -04:00
Beat Küng a8e75d174c boards: remove BOARD_HAS_PWM and use DIRECT_PWM_OUTPUT_CHANNELS 2021-09-08 16:10:24 -04:00