* added a new driver ASP5033 for measuring the differential pressure and airspeed
---------
Co-authored-by: nano <nanobotzhe@abv.bg>
Co-authored-by: Denislav Petrov <you@example.com>
When the yaw estimate is converging, the controller makes the drone yaw
in order to follow the current setpoint. This is unintuitive for the
pilot and it is preferable if the drone continues to fly towards the
same physical direction.
This estimate doesn't converge to the true yaw but can be used as a
more consistent but drifting heading source.
It can be used by a setpoint generator to adjust its heading setpoint
while the true yaw estimate is converging in order to keep a constant
course over ground.
This updates the gps/devices submodule which includes a fix that
requests the Unicore HEADINGA message in case the message is not enabled
by default.
Signed-off-by: Julian Oes <julian@oes.ch>
If the measured voltage is more than 65v we need to split the voltage
over multiple cells in order to avoid overflowing the uint16. This is
according to the MAVLink spec.
Signed-off-by: Julian Oes <julian@oes.ch>
The extension fields need to be 0 by default according to the MAVLink
spec. This is because extensions are 0 by default and need to be 0 when
unknown/unused for backwards compatibility.
The patch also simplifies the flow slightly in that it doesn't create a
temporary array but just fills in the cell voltages directly.
Signed-off-by: Julian Oes <julian@oes.ch>
Fixes the clang error:
/__w/PX4-Autopilot/PX4-Autopilot/src/drivers/drv_hrt.h:297:35: fatal error: identifier '_s' preceded by whitespace in a literal operator declaration is deprecated [-Wdeprecated-literal-operator]
297 | constexpr hrt_abstime operator "" _s(unsigned long long seconds)
- Enable arbitrary euler angle for Mag rotation
- new CUSTOM rotation enum out of the normal enum range
- mag_rot: automatically change to custom if euler rot is set
- sensor_calibration: Magnetometer save custom rotation parameters
- mag_cal: cross mention rotation parameters
- This allows the user to see the RPY options when searching for the rotation parameter
---------
Co-authored-by: Junwoo Hwang <junwoo@auterion.com>
Co-authored-by: bresch <[brescianimathieu@gmail.com](mailto:brescianimathieu@gmail.com)>
Co-authored-by: Daniel Agar <daniel@agar.ca>
During transition to FF, only allow update thrust axis up to 45° as with a high tilt angle
the effectiveness of the thrust axis in z is apporaching 0, and by that is increasing
the motor output to max.
Transition to HF: disable thrust axis tilting, and assume motors are vertical. This is to avoid
a thrust spike when the transition is initiated (as then the tilt is fully forward).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
EffectivenessTiltrotor: link time when to tilt motors to MC position to COM_SPOOLUP_TIME
- remove VT_TILT_SPINUP and special spin up tilt handling form the VTOL module
- now handle the spoolup in the allocation, directly linked to COM_SPOOLUP_TIME
- leave tilts at disarmed value during spoolup
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- when GNSS is used require low mag heading innovations during
horizontal acceleration (yaw observable) to validate the mag
- only fuse mag heading just enough to constrain the yaw estimate
variance to a sane value. Leave enough uncertainty to allow for a
correction when the yaw is observable through GNSS fusion
In the mavlink_receiver code, after a while it will try to resend some
parameter update through the MAVLink instance. But for Iridium links
those are not a good idea. So this adds a condition that prevent the
sending if the MAVLink instance is in Iridium mode.
Related to issue #21496
sem_wait() can be interrupted if the task receives a signal, however
the blockinglist implementation depends on blocking until the semaphore
can be obtained.
alexklimaj
Jukka Laitinen
Julian Oes
Denislav Petrov
Matthias Grob
bresch
comla-x
Niklas Hauser
Daniel Agar
Beat Küng
Mathieu Bresciani
Silvan Fuhrer
Daniel Mesham
Peter van der Perk
Ludovic Vanasse
Sverre Velten Rothmund
PX4 BuildBot
Ville Juven