These changes remove the two code paths to updates (forceupdate and update) and try to reboot and bootload IO independent of its state, wether it is in bootloader mode already, safety switch is off or if it is in "nominal state" (running and safety on). This ensures that there are no conditions where user error or boot sequence can prevent a successful upgrade. The only state where an upgrade will not be done is if the system is fully armed.
Previously, we did not set a remote port which meant that the default
remote port 14550 was used. This meant that the mavlink instance
talking to the gimbal was interfering with the connection to the ground
station (on 14550).
This is a hack to make sure the messages from the gimbal arrive at other
links (e.g. the ground station). It means that the gimbal does not get
flooded with all other messages that would get forwarded but messages
from the gimbal will still make it through.
* Commit for the Integration of a position controller for the a Underwater vehicle.
This module is an extension of the uuv_att_control to control an Underwater vehicle to any position, given by the SET_POSITION_TARGET_LOCAL_NED which includes x y z yaw.
Since the position control is designed for a 6DOF Robot, the roll and pitch angle are controlled to be 0.
Additionally there is a stabilization control, which holds the robot at a defined depth, and not move in any direction.
In general the idea is to have this position module to control the position of the uuv. The position module reseives the desired position of the uuv and sends appropriate attitude setpoints to the uuv_attitude_control module.
Additionally the mixer file is adapted, to include the 6 different inputs(x y z roll pitch yaw).
* Commit for the Integration of a position controller for the a Underwater vehicle.
This module is an extension of the uuv_att_control to control an Underwater vehicle to any position, given by the SET_POSITION_TARGET_LOCAL_NED which includes x y z yaw.
Since the position control is designed for a 6DOF Robot, the roll and pitch angle are controlled to be 0.
Additionally there is a stabilization control, which holds the robot at a defined depth, and not move in any direction.
In general the idea is to have this position module to control the position of the uuv. The position module receives the desired position of the uuv and sends appropriate attitude setpoints to the uuv_attitude_control module.
Additionally the mixer file is adapted, to include the 6 different inputs(x y z roll pitch yaw).
Currently not solved/missing:
- Problem with gazebo model(propeller moving chaotically).
- Mixer correct gazebo vs real life (has to be tested in the future)
- correct integration in uuv.apps (when choose which module)
- very basic controller chosen (could be improved a lot in the future)
* Remove error caused by unused variables and a different build error
* added better description of the parameter. Additionally the group is changed.
* added better description of the parameter. Additionally the group is changed.
Fixed bug about parameter
* Added EOF to the files.
* Removed parameter for direct position control for safety reasons.
* small bugfix
This commit moves the steering output from yaw to the roll channel to better reflect the lateral control input / reaction mapping. It also removes old unused parameters and modernizes the mainloop to remove unnecessary polling.
This system command will display, set and save the network
settings.
netman show - Displays the current settings.
netman update - Will check for a net.cfg file on the SD card.
If present, it will update the paramaters,
delete the file, and reboot. Using the new settings.
netman save - Saves the current settings to net.cfg on the SD card.
This file shoulf be renamed to preserver it across
reboots or editited to chech networkin paramates.
File format is name<space>value:
echo DEVICE=eth0 > /fs/microsd/net.cfg
echo BOOTPROTO=fallback >> /fs/microsd/net.cfg
echo IPADDR=192.168.0.4 >> /fs/microsd/net.cfg
echo NETMASK=255.255.255.0 >>/fs/microsd/net.cfg
echo ROUTER=192.168.0.254 >>/fs/microsd/net.cfg
echo DNS=192.168.0.254 >>/fs/microsd/net.cfg
Valid values for `proto` are `dhcp`, `static`, `falback`
Both will try dhcp for CONFIG_NETINIT_FALLBACK times
and fall back to the static address.
NETMASK - is the network mask.
IPADDR - this nodes ip address for static or fall back.
ROUTER - The default route.
DNS - The address of the dns server.
- generate PWM_MAIN 1-14
- generate PWM_AUX 1-8
- generate PWM_EXTRA 1-8
- px4io and pwm_out directly read configuration parameters
- only available and active physical outputs are actually shown for configuration
- overall saves flash despite adding many new parameters
- control allocation module with multirotor, VTOL standard, and tiltrotor support
- angular_velocity_controller
- See https://github.com/PX4/PX4-Autopilot/pull/13351 for details
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
Co-authored-by: Roman Bapst <bapstroman@gmail.com>
- commander preflightcheck use estimator_sensor_bias message instead of EKF state index magic number
- ekf2 publish estimated bias limits in estimator_sensor_bias
- preflightcheck only error if bias estimate exceeds half of configured limit (delete COM_ARM_EKF_AB and COM_ARM_EKF_GB parameters)
- ekf2 can now run in multi-instance mode (currently up to 9 instances)
- in multi mode all estimates are published to alternate topics (eg estimator_attitude instead of vehicle_attitude)
- new ekf2 selector runs in multi-instance mode to monitor and compare all instances, selecting a primary (eg N x estimator_attitude => vehicle_attitude)
- sensors module accel & gyro inconsistency checks are now relative to the mean of all instances, rather than the current primary (when active ekf2 selector is responsible for choosing primary accel & gyro)
- existing consumers of estimator_status must check estimator_selector_status to select current primary instance status
- ekf2 single instance mode is still fully supported and the default
Co-authored-by: Paul Riseborough <gncsolns@gmail.com>
- add new parameter `IMU_GYRO_FFT_EN` to start
- add 75% overlap in buffer to increase FFT update rate
- space out FFT calls (no more than 1 per cycle)
- increase `IMU_GYRO_FFT_MIN` default
- decrease main stack usage
* Add techpod SITL target
This adds a SITL target forthe techpod fixedwing model
* Update sitl_gazebo submoudle
This submodule update includes the techpod UAV model
- drivers/tone_alarm: move to ModuleBase and purge CDev (/dev/tone_alarm0)
- drivers/tone_alarm: only run on tune_control publication (or scheduled note) rather than continuously
- drivers/tone_alarm: use HRT to schedule tone stop (prevents potential disruption)
- msg/tune_control: add tune_id numbering
- systemcmds/tune_control: add "error" special case tune_id
- move all tune_control publication to new uORB::PublicationQueued<>
- start tone_alarm immediately after board defaults are loaded to fix potential startup issues
- for SITL (or other boards with no TONE output) print common messages (startup, error, etc)
* Add jsbsim bridge to enable jsbsim for px4 SITL/HIL on jsbsim
This is a PX4 HIL/SITL integration into JSBSim. JSBSim is an open source flight dynamics model (http://jsbsim.sourceforge.net/)
Currently there are three models available which is the rascal, quadrotor_x, hexarotor_x integrated into the bridge.
The simulation can be run with the firmware with the following command for example
```
make px4_sitl jsbsim_rascal
```
The visualization is done flightgear and is done by the bridge sending UDP packets to flightgear. To disable the visualization `HEADLESS=1` when running the make command.
The simulation can be configured through the configuration files under the `config` directory through a xml file. Senor configurations, The xml file name should match the name of the model.
* Update Tools/sitl_run.sh
Co-authored-by: Beat Küng <beat-kueng@gmx.net>
Co-authored-by: Beat Küng <beat-kueng@gmx.net>
Beat Küng
JacobCrabill
Lorenz Meier
Julian Oes
Daniel Agar
Tim
Jaeyoung-Lim
Mathieu Bresciani
xdwgood
JaeyoungLim
David Sidrane
Roman Dvořák
Jakub Kákona
honglang
TheLegendaryJedi
Julien Lecoeur
Ricardo Marques
Silvan Fuhrer
Can Berk Durmus
RomanBapst
Matthias Grob
Orkun Aşa
Orkun Aşa
Hamish Willee
Thies Lennart Alff
SalimTerryLi
bazooka joe