- same pattern as other new drivers (state machine, checked register mechanism, no sleeps, etc)
- self test has been rolled into regular startup sequence
- still I2C only, but will be expanded in the future
- configure to high accuracy preset
- currently the main change is that it reduces the max number of ORB multi instances to 4, but usage will be expanded as needed
- limits number of EKF2 multi instances to 2.
- enabled on all cortex m4 boards
- simple state machine to reset, configure, etc
- checked register mechanism (sensor will reset itself on configuration error)
- configured in 16 bit mode (1320 LSB/Gauss instead of 330 LSB/Gauss)
- adjusted orientation handling in driver to match datasheet as closely as possible
- in many external compass units the rotation was wrong and very difficult to actual determine how to set correctly
- always check with state machine before reboot/shutdown
- respect BOARD_HAS_POWER_CONTROL (shutdown from command, low battery, power button)
- px4_shutdown_request add optional delay and always execute from HPWORK
- px4_shutdown_request split out px4_reboot_request
- increase stack sizes to run cleanly under stackcheck
- this is likely overkill for most boards, but using stackcheck to set our minimum ensures we have a very safe margin on regular builds and it's something we can currently afford
- remove holybro_durandal-v1_stackcheck from test rack (there's only one unit)
- interupt pin set active low and latch
- relax retry timeout if configure failed
- improve configured empty rate (sample rate) rounding
- fix RegisterCheck
- check FIFO count as part of full transfer and reset or adjust timing if necessary
- rename DRV_IMU_DEVTYPE_ICM20608 -> DRV_IMU_DEVTYPE_ICM20608G
- update to NuttX with stm32f4 and stm32f7 SPI DMA internal buffers
- remove explicit DMA buffer allocations from new IMU drivers
- restore original BOARD_DMA_ALLOC_POOL_SIZE
- decrease SPI DMA thresholds based on fmu-v2/v3/v4/v5 bench testing
* MC_HTE: unitialize with hover_thrust parameter
* MC_HTE: constrain hover thrust setter between 0.1 and 0.9
* MC_HTE: integrate with land detector and velocity controller
* MCHoverThrustEstimator: Always publish an estimate even when not fusing measurements. This is required as the land detector and the position controller need to receive a hover thrust value.
* MC_HTE: use altitude agl threshold to start the estimator
local_position.z is relative to the origin of the EKF while dist_bottom
is above ground
Co-authored-by: bresch <brescianimathieu@gmail.com>
Chip-select and SPI initialization uses the new config, whereas the drivers
still use the existing defines.
The configuration in board_config.h can be removed after all drivers are
updated.
- reduces amount of board configuration required
- removes the cyclic dependency between io_timers_t and timer_io_channels_t
Fixes a bug in the fmuk66-v3 config: the 2. timer has 3 channels associated
not 2.
Fixes a bug in the modelai config: the 2. timer has 4 channels associated.
- this is a new module for temperature compensation that consolidates the functionality previously handled in the sensors module (calculating runtime thermal corrections) and the events module (online thermal calibration)
- by collecting this functionality into a single module we can optionally disable it on systems where it's not used and save some flash (if disabled at build time) or memory (disabled at run time)
* A few minor changes to keep the UVify Core board in sync with fmu-v4. This will be important when transitioning to the new IMU drivers using SPI DMA (#13103).
* Draco-R sensor orientation correction
* LL40LS sensor is not stable during I2C probing. More trials have been implemented.
* px4flow execution has been removed as rc script already running it
* GPS LED script repaired
* Off ICM20608 due to some bug?
* Removed i2c speed adjustment due to SMBUS.
* ms5611 test2 does not exist
* Baud rate has changed.
* Draco-R airframe parameters are updated.
* IFO and Draco parameters are updated
* Draco-R sensor orientation corrected
* Draco-R DSHOT supports
and remove the px4_ prefix, except for px4_config.h.
command to update includes:
for k in app.h atomic.h cli.h console_buffer.h defines.h getopt.h i2c.h init.h log.h micro_hal.h module.h module_params.h param.h param_macros.h posix.h sem.h sem.hpp shmem.h shutdown.h tasks.h time.h workqueue.h; do for i in $(grep -rl 'include <px4_'$k src platforms boards); do sed -i 's/#include <px4_'$k'/#include <px4_platform_common\/'$k/ $i; done; done
for in $(grep -rl 'include <px4_config.h' src platforms boards); do sed -i 's/#include <px4_config.h/#include <px4_platform_common\/px4_config.h'/ $i; done
Transitional headers for submodules are added (px4_{defines,log,time}.h)
* adds a work_queue systemcmd that will bring a tree view of all active work queues and work items
* WorkQueues now track attached WorkItems and will shutdown when the last WorkItem is detached
-moved rc.mavlink to the boards optional rc additions (now it's called rc.board_mavlink) to handle board specific mavlink needs (mavlink over usb, ethernet, additional streams, etc.)
-mavlink module will be responsible to usb defaults, therefore less args are needed to be passed to mavlink module if one wants to use mavlink over usb.
-the way to check if connection is usb is by it's designated variable and not by config mode.
Kirill Shilov
David Sidrane
Daniel Agar
Matthias Grob
Tanja Baumann
SalimTerryLi
Beat Küng
mcsauder
Hyon Lim
garfieldG
BazookaJoe1900
Hyon Lim