uint16 VEHICLE_CMD_NAV_WAYPOINT = 16 # Navigate to MISSION. |Hold time in decimal seconds. (ignored by fixed wing, time to stay at MISSION for rotary wing)| Acceptance radius in meters (if the sphere with this radius is hit, the MISSION counts as reached)| 0 to pass through the WP, if > 0 radius in meters to pass by WP. Positive value for clockwise orbit, negative value for counter-clockwise orbit. Allows trajectory control.| Desired yaw angle at MISSION (rotary wing)| Latitude| Longitude| Altitude|
uint16 VEHICLE_CMD_NAV_LOITER_UNLIM = 17 # Loiter around this MISSION an unlimited amount of time |Empty| Empty| Radius around MISSION, in meters. If positive loiter clockwise, else counter-clockwise| Desired yaw angle.| Latitude| Longitude| Altitude|
uint16 VEHICLE_CMD_NAV_LOITER_TURNS = 18 # Loiter around this MISSION for X turns |Turns| Empty| Radius around MISSION, in meters. If positive loiter clockwise, else counter-clockwise| Desired yaw angle.| Latitude| Longitude| Altitude|
uint16 VEHICLE_CMD_NAV_LOITER_TIME = 19 # Loiter around this MISSION for X seconds |Seconds (decimal)| Empty| Radius around MISSION, in meters. If positive loiter clockwise, else counter-clockwise| Desired yaw angle.| Latitude| Longitude| Altitude|
uint16 VEHICLE_CMD_DO_ORBIT = 34 # Start orbiting on the circumference of a circle defined by the parameters. |Radius [m] |Velocity [m/s] |Yaw behaviour |Empty |Latitude/X |Longitude/Y |Altitude/Z |
uint16 VEHICLE_CMD_NAV_ROI = 80 # Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of interest mode. (see MAV_ROI enum)| MISSION index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|
uint16 VEHICLE_CMD_NAV_PATHPLANNING = 81 # Control autonomous path planning on the MAV. |0: Disable local obstacle avoidance / local path planning (without resetting map), 1: Enable local path planning, 2: Enable and reset local path planning| 0: Disable full path planning (without resetting map), 1: Enable, 2: Enable and reset map/occupancy grid, 3: Enable and reset planned route, but not occupancy grid| Empty| Yaw angle at goal, in compass degrees, [0..360]| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal|
uint16 VEHICLE_CMD_NAV_VTOL_TAKEOFF = 84 # Takeoff from ground / hand and transition to fixed wing |Minimum pitch (if airspeed sensor present), desired pitch without sensor| Empty| Empty| Yaw angle (if magnetometer present), ignored without magnetometer| Latitude| Longitude| Altitude|
uint16 VEHICLE_CMD_NAV_VTOL_LAND = 85 # Transition to MC and land at location |Empty| Empty| Empty| Desired yaw angle.| Latitude| Longitude| Altitude|
uint16 VEHICLE_CMD_NAV_GUIDED_LIMITS = 90 # set limits for external control |timeout - maximum time (in seconds) that external controller will be allowed to control vehicle. 0 means no timeout| absolute altitude min (in meters, AMSL) - if vehicle moves below this alt, the command will be aborted and the mission will continue. 0 means no lower altitude limit| absolute altitude max (in meters)- if vehicle moves above this alt, the command will be aborted and the mission will continue. 0 means no upper altitude limit| horizontal move limit (in meters, AMSL) - if vehicle moves more than this distance from it's location at the moment the command was executed, the command will be aborted and the mission will continue. 0 means no horizontal altitude limit| Empty| Empty| Empty|
uint16 VEHICLE_CMD_NAV_GUIDED_MASTER = 91 # set id of master controller |System ID| Component ID| Empty| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_NAV_GUIDED_ENABLE = 92 # hand control over to an external controller |On / Off (> 0.5f on)| Empty| Empty| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_NAV_DELAY = 93 # Delay the next navigation command a number of seconds or until a specified time |Delay in seconds (decimal, -1 to enable time-of-day fields)| hour (24h format, UTC, -1 to ignore)| minute (24h format, UTC, -1 to ignore)| second (24h format, UTC)| Empty| Empty| Empty|
uint16 VEHICLE_CMD_NAV_LAST = 95 # NOP - This command is only used to mark the upper limit of the NAV/ACTION commands in the enumeration |Empty| Empty| Empty| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_CONDITION_DELAY = 112 # Delay mission state machine. |Delay in seconds (decimal)| Empty| Empty| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_CONDITION_CHANGE_ALT = 113 # Ascend/descend at rate. Delay mission state machine until desired altitude reached. |Descent / Ascend rate (m/s)| Empty| Empty| Empty| Empty| Empty| Finish Altitude|
uint16 VEHICLE_CMD_CONDITION_DISTANCE = 114 # Delay mission state machine until within desired distance of next NAV point. |Distance (meters)| Empty| Empty| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_CONDITION_YAW = 115 # Reach a certain target angle. |target angle: [0-360], 0 is north| speed during yaw change:[deg per second]| direction: negative: counter clockwise, positive: clockwise [-1,1]| relative offset or absolute angle: [ 1,0]| Empty| Empty| Empty|
uint16 VEHICLE_CMD_CONDITION_LAST = 159 # NOP - This command is only used to mark the upper limit of the CONDITION commands in the enumeration |Empty| Empty| Empty| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_DO_SET_MODE = 176 # Set system mode. |Mode, as defined by ENUM MAV_MODE| Empty| Empty| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_DO_JUMP = 177 # Jump to the desired command in the mission list. Repeat this action only the specified number of times |Sequence number| Repeat count| Empty| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_DO_CHANGE_SPEED = 178 # Change speed and/or throttle set points. |Speed type (0=Airspeed, 1=Ground Speed)| Speed (m/s, -1 indicates no change)| Throttle ( Percent, -1 indicates no change)| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_DO_SET_HOME = 179 # Changes the home location either to the current location or a specified location. |Use current (1=use current location, 0=use specified location)| Empty| Empty| Empty| Latitude| Longitude| Altitude|
uint16 VEHICLE_CMD_DO_SET_PARAMETER = 180 # Set a system parameter. Caution! Use of this command requires knowledge of the numeric enumeration value of the parameter. |Parameter number| Parameter value| Empty| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_DO_SET_RELAY = 181 # Set a relay to a condition. |Relay number| Setting (1=on, 0=off, others possible depending on system hardware)| Empty| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_DO_REPEAT_RELAY = 182 # Cycle a relay on and off for a desired number of cyles with a desired period. |Relay number| Cycle count| Cycle time (seconds, decimal)| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_DO_SET_SERVO = 183 # Set a servo to a desired PWM value. |Servo number| PWM (microseconds, 1000 to 2000 typical)| Empty| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_DO_REPEAT_SERVO = 184 # Cycle a between its nominal setting and a desired PWM for a desired number of cycles with a desired period. |Servo number| PWM (microseconds, 1000 to 2000 typical)| Cycle count| Cycle time (seconds)| Empty| Empty| Empty|
uint16 VEHICLE_CMD_DO_LAND_START = 189 # Mission command to perform a landing. This is used as a marker in a mission to tell the autopilot where a sequence of mission items that represents a landing starts. It may also be sent via a COMMAND_LONG to trigger a landing, in which case the nearest (geographically) landing sequence in the mission will be used. The Latitude/Longitude is optional, and may be set to 0/0 if not needed. If specified then it will be used to help find the closest landing sequence. |Empty| Empty| Empty| Empty| Latitude| Longitude| Empty| */
uint16 VEHICLE_CMD_DO_SET_ROI_LOCATION = 195 # Sets the region of interest (ROI) to a location. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Empty| Empty| Empty| Empty| Latitude| Longitude| Altitude|
uint16 VEHICLE_CMD_DO_SET_ROI_WPNEXT_OFFSET = 196 # Sets the region of interest (ROI) to be toward next waypoint, with optional pitch/roll/yaw offset. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Empty| Empty| Empty| Empty| pitch offset from next waypoint| roll offset from next waypoint| yaw offset from next waypoint|
uint16 VEHICLE_CMD_DO_SET_ROI_NONE = 197 # Cancels any previous ROI command returning the vehicle/sensors to default flight characteristics. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Empty| Empty| Empty| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_DO_CONTROL_VIDEO = 200 # Control onboard camera system. |Camera ID (-1 for all)| Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw| Transmission mode: 0: video stream, >0: single images every n seconds (decimal)| Recording: 0: disabled, 1: enabled compressed, 2: enabled raw| Empty| Empty| Empty|
uint16 VEHICLE_CMD_DO_SET_ROI = 201 # Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of interest mode. (see MAV_ROI enum)| MISSION index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|
uint16 VEHICLE_CMD_DO_DIGICAM_CONTROL=203
uint16 VEHICLE_CMD_DO_MOUNT_CONFIGURE=204 # Mission command to configure a camera or antenna mount |Mount operation mode (see MAV_MOUNT_MODE enum)| stabilize roll? (1 = yes, 0 = no)| stabilize pitch? (1 = yes, 0 = no)| stabilize yaw? (1 = yes, 0 = no)| Empty| Empty| Empty|
uint16 VEHICLE_CMD_DO_MOUNT_CONTROL=205 # Mission command to control a camera or antenna mount |pitch or lat in degrees, depending on mount mode.| roll or lon in degrees depending on mount mode| yaw or alt (in meters) depending on mount mode| reserved| reserved| reserved| MAV_MOUNT_MODE enum value|
uint16 VEHICLE_CMD_DO_SET_CAM_TRIGG_DIST=206 # Mission command to set TRIG_DIST for this flight |Camera trigger distance (meters)| Shutter integration time (ms)| Empty| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_DO_FENCE_ENABLE=207 # Mission command to enable the geofence |enable? (0=disable, 1=enable)| Empty| Empty| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_DO_PARACHUTE=208 # Mission command to trigger a parachute |action (0=disable, 1=enable, 2=release, for some systems see PARACHUTE_ACTION enum, not in general message set.)| Empty| Empty| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_DO_SET_CAM_TRIGG_INTERVAL=214 # Mission command to set TRIG_INTERVAL for this flight |Camera trigger distance (meters)| Shutter integration time (ms)| Empty| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_DO_MOUNT_CONTROL_QUAT=220 # Mission command to control a camera or antenna mount, using a quaternion as reference. |q1 - quaternion param #1, w (1 in null-rotation)| q2 - quaternion param #2, x (0 in null-rotation)| q3 - quaternion param #3, y (0 in null-rotation)| q4 - quaternion param #4, z (0 in null-rotation)| Empty| Empty| Empty|
uint16 VEHICLE_CMD_DO_GUIDED_MASTER=221 # set id of master controller |System ID| Component ID| Empty| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_DO_GUIDED_LIMITS=222 # set limits for external control |timeout - maximum time (in seconds) that external controller will be allowed to control vehicle. 0 means no timeout| absolute altitude min (in meters, AMSL) - if vehicle moves below this alt, the command will be aborted and the mission will continue. 0 means no lower altitude limit| absolute altitude max (in meters)- if vehicle moves above this alt, the command will be aborted and the mission will continue. 0 means no upper altitude limit| horizontal move limit (in meters, AMSL) - if vehicle moves more than this distance from it's location at the moment the command was executed, the command will be aborted and the mission will continue. 0 means no horizontal altitude limit| Empty| Empty| Empty|
uint16 VEHICLE_CMD_DO_LAST = 240 # NOP - This command is only used to mark the upper limit of the DO commands in the enumeration |Empty| Empty| Empty| Empty| Empty| Empty| Empty|
uint16 VEHICLE_CMD_PREFLIGHT_CALIBRATION = 241 # Trigger calibration. This command will be only accepted if in pre-flight mode. See mavlink spec MAV_CMD_PREFLIGHT_CALIBRATION
uint16 VEHICLE_CMD_PREFLIGHT_SET_SENSOR_OFFSETS = 242 # Set sensor offsets. This command will be only accepted if in pre-flight mode. |Sensor to adjust the offsets for: 0: gyros, 1: accelerometer, 2: magnetometer, 3: barometer, 4: optical flow| X axis offset (or generic dimension 1), in the sensor's raw units| Y axis offset (or generic dimension 2), in the sensor's raw units| Z axis offset (or generic dimension 3), in the sensor's raw units| Generic dimension 4, in the sensor's raw units| Generic dimension 5, in the sensor's raw units| Generic dimension 6, in the sensor's raw units|
uint16 VEHICLE_CMD_PREFLIGHT_STORAGE = 245 # Request storage of different parameter values and logs. This command will be only accepted if in pre-flight mode. |Parameter storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM| Mission storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM| Reserved| Reserved| Empty| Empty| Empty|
uint16 VEHICLE_CMD_PREFLIGHT_REBOOT_SHUTDOWN = 246 # Request the reboot or shutdown of system components. |0: Do nothing for autopilot, 1: Reboot autopilot, 2: Shutdown autopilot.| 0: Do nothing for onboard computer, 1: Reboot onboard computer, 2: Shutdown onboard computer.| Reserved| Reserved| Empty| Empty| Empty|
uint16 VEHICLE_CMD_MISSION_START = 300 # start running a mission |first_item: the first mission item to run| last_item: the last mission item to run (after this item is run, the mission ends)|
uint16 VEHICLE_CMD_COMPONENT_ARM_DISARM = 400 # Arms / Disarms a component |1 to arm, 0 to disarm|
