2011-12-19 15:24:09 -04:00
|
|
|
|
configs/pic32-starterkit README
|
|
|
|
|
|
===============================
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This README file discusses the port of NuttX to the Microchip PIC32 Ethernet
|
|
|
|
|
|
Starter Kit (DM320004) with the Multimedia Expansion Board (MEB, DM320005).
|
|
|
|
|
|
See www.microchip.com for further information.
|
|
|
|
|
|
|
|
|
|
|
|
The PIC32 Ethernet Starter Kit includes:
|
|
|
|
|
|
|
|
|
|
|
|
- PIC32MX795F512L 32-bit microcontroller.
|
|
|
|
|
|
- PIC32MX795F512L USB microcontroller for on-board debugging.
|
|
|
|
|
|
- Green power indicator LED.
|
|
|
|
|
|
- Orange debug indicator LED.
|
|
|
|
|
|
- Three user-defined indicator LEDs.
|
|
|
|
|
|
- Ethernet 10/100 bus speed indicator LED.
|
|
|
|
|
|
- Three push button switches for user-defined inputs.
|
|
|
|
|
|
- On-board crystal for precision microcontroller clocking (8 MHz).
|
|
|
|
|
|
- 50 MHz Ethernet PHY oscillator.
|
|
|
|
|
|
- 32 kHz oscillator (optional).
|
|
|
|
|
|
- USB connectivity for on-board debugger communications.
|
|
|
|
|
|
- USB Host and OTG power supply for powering PIC32 USB applications.
|
|
|
|
|
|
- USB Type A receptacle connectivity for PIC32 host-based applications.
|
|
|
|
|
|
- USB Type micro-AB receptacle for OTG and USB device connectivity for PIC32
|
|
|
|
|
|
OTG/device-based applications.
|
|
|
|
|
|
- RJ-45 Ethernet port (External Ethernet PHY).
|
|
|
|
|
|
|
|
|
|
|
|
The MEB adds:
|
|
|
|
|
|
|
|
|
|
|
|
- 3.2 inch (8.1 cm) QVGA touch screen display with backlight
|
|
|
|
|
|
- Solomon Systech Graphics Controller (SSD1926)
|
|
|
|
|
|
- Five user-controlled LEDs
|
|
|
|
|
|
- Power LED
|
|
|
|
|
|
- Four-way joystick
|
|
|
|
|
|
- Fire button
|
|
|
|
|
|
- Headphone jack
|
|
|
|
|
|
- Line output jack
|
|
|
|
|
|
- Microphone input jack
|
|
|
|
|
|
- microSD card slot.
|
|
|
|
|
|
- Accelerometer and temperature sensor
|
|
|
|
|
|
- 24LC08 EEPROM.
|
|
|
|
|
|
- SPI Flash
|
|
|
|
|
|
- 24-bit audio codec
|
|
|
|
|
|
- CPLD for SPI and Chip Select configuration
|
|
|
|
|
|
- Integrated 802.11 wireless connectivity
|
|
|
|
|
|
|
|
|
|
|
|
Contents
|
|
|
|
|
|
========
|
|
|
|
|
|
|
|
|
|
|
|
PIC32MX795F512L Pin Out
|
|
|
|
|
|
MEB Connector
|
2011-12-23 19:36:34 -04:00
|
|
|
|
PICtail
|
2011-12-19 15:24:09 -04:00
|
|
|
|
Toolchains
|
2011-12-24 09:46:06 -04:00
|
|
|
|
Powering the Board
|
2011-12-25 10:28:12 -04:00
|
|
|
|
Creating Compatible NuttX HEX files
|
2011-12-23 19:36:34 -04:00
|
|
|
|
Serial Console
|
2011-12-25 11:56:08 -04:00
|
|
|
|
LEDs
|
2011-12-19 15:24:09 -04:00
|
|
|
|
PIC32MX Configuration Options
|
|
|
|
|
|
Configurations
|
|
|
|
|
|
|
|
|
|
|
|
PIC32MX795F512L Pin Out
|
|
|
|
|
|
=======================
|
|
|
|
|
|
|
|
|
|
|
|
LEFT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left)
|
|
|
|
|
|
--- ---------------------------------- -------------------------- -----------------------------------------------
|
|
|
|
|
|
PIN CONFIGURATIONS SIGNAL NAME ON-BOARD CONNECTIONS
|
|
|
|
|
|
(Family Data Sheet Table 1-1) (Starter Kit User Guide)
|
|
|
|
|
|
--- ---------------------------------- -------------------------- -----------------------------------------------
|
|
|
|
|
|
1 RG15/AERXERR ERXERR Ethernet RX_ER/MDIX_IN
|
|
|
|
|
|
2 VDD P32_VDD ---
|
|
|
|
|
|
3 PMD5/RE5 PMPD5/RE5 J2 pin 13
|
|
|
|
|
|
4 PMD6/RE6 PMPD6/RE6 J2 pin 9
|
|
|
|
|
|
5 PMD7/RE7 PMPD7/RE7 J2 pin 7
|
|
|
|
|
|
6 RC1/T2CK T2CLK/RC1 J2 pin 35 (timer)
|
|
|
|
|
|
7 RC2/AC2TX/T3CK T3CLK/RC2 J2 pin 37 (timer)
|
|
|
|
|
|
8 RC3/AC2RX/T4CK T4CLK/RC3 J2 pin 39 (timer)
|
|
|
|
|
|
9 RC4/SDI1/T5CK SDI1/T4CLK/RC4 J2 pin 41 (timer)
|
|
|
|
|
|
J2 pin 93 (SPI1)
|
|
|
|
|
|
10 PMA5/CN8/ECOL/RG6/SCK2/U3RTS/U6TX PMPA5/SCM2C/CN8/RG6 J2 pin 45 (SPI2)
|
|
|
|
|
|
J2 pin 117 (PMP address)
|
|
|
|
|
|
11 PMA4/CN9/ECRS/RG7/SDA4/SDI2/U3RX PMPA4/SCM2A/CN9/RG7 J2 pin 47 (SPI2)
|
|
|
|
|
|
J2 pin 119 (PMP address)
|
|
|
|
|
|
12 PMA3/AECRSDV/AERXDV/CN10/ECRSDV/ ECRS_DV Ethernet CRS/CRS_DV/LED_CFG
|
|
|
|
|
|
ERXDV/RG8/SCL4/SDO2/U3TX
|
|
|
|
|
|
13 MCLR PIC32_MCLR (pulled up)
|
|
|
|
|
|
PIC32MX440F512H debug processor
|
|
|
|
|
|
J2 pin 130 (ICSP)
|
|
|
|
|
|
14 PMA2/AEREFCLK/AERXCLK/CN11/ EREF_CLK 50MHz clock, Ethernet X1
|
|
|
|
|
|
EREFCLK/ERXCLK/RG9/SS2/U3CTS/
|
|
|
|
|
|
U6RX
|
|
|
|
|
|
15 VSS (grounded) ---
|
|
|
|
|
|
16 VDD P32_VDD ---
|
|
|
|
|
|
17 RA0/TMS TMS/RA0 J2 pin 126 (JTAG/GPIO)
|
|
|
|
|
|
18 AERXD0/INT1/RE8 ERXD0(2) Ethernet RXD_0/PHYAD1
|
|
|
|
|
|
19 AERXD1/INT2/RE9 ERXD1(2) Ethernet RXD_1/PHYAD2
|
|
|
|
|
|
20 AN5/C1IN+/CN7/RB5/VBUSON VBUSON/C1IN+/AN5/CN7/RB5 USB host power supply, TPS20x1B ~EN,
|
|
|
|
|
|
Low enables power to host port (J4)
|
|
|
|
|
|
USB OTG power supply, MCP1253_MSOP ~SHDN
|
|
|
|
|
|
Enables power to device/OTG port (J5)
|
|
|
|
|
|
J2 pin 63 (comparator 1)
|
|
|
|
|
|
J2 pin 62 (A/D)
|
|
|
|
|
|
21 AN4/C1IN-/CN6/RB4 USBOEN/C1IN-/AN4/CN6/RB4 J2 pin 65 (comparator 1)
|
|
|
|
|
|
J2 pin 64 (A/D)
|
|
|
|
|
|
22 AN3/C2IN+/CN5/RB3 C2IN+/AN3/CN5/RB3 TPS20x1B ~OC, sense host port power
|
|
|
|
|
|
MCP1253_MSOP PGOOD, sense device/OTG port power
|
|
|
|
|
|
J2 pin 67 (comparator 2)
|
|
|
|
|
|
J2 pin 66 (A/D)
|
|
|
|
|
|
23 AN2/C2IN-/CN4/RB2 C2IN-/AN2/CN4/RB2 J2 pin 69 (comparator 2)
|
|
|
|
|
|
J2 pin 101
|
|
|
|
|
|
J2 pin 68 (A/D)
|
|
|
|
|
|
24 AN1/CN3/PGEC1/RB1 PGC1/AN1/CN3/RB1 J2 pin 70 (A/D)
|
|
|
|
|
|
25 AN0/CN2/PGED1/RB0 PGD1/AN0/CN2/RB0 J2 pin 72 (A/D)
|
|
|
|
|
|
|
|
|
|
|
|
BOTTOM SIDE, LEFT-TO-RIGHT (if pin 1 is in upper left)
|
|
|
|
|
|
--- ---------------------------------- -------------------------- -----------------------------------------------
|
|
|
|
|
|
PIN CONFIGURATIONS SIGNAL NAME ON-BOARD CONNECTIONS
|
|
|
|
|
|
(Family Data Sheet Table 1-1) (Starter Kit User Guide)
|
|
|
|
|
|
--- ---------------------------------- -------------------------- -----------------------------------------------
|
|
|
|
|
|
26 AN6/OCFA/PGEC2/RB6 PIC32_PGC2 PIC32MX440F512H debug processor
|
|
|
|
|
|
J2 pin 128 (ICSP)
|
|
|
|
|
|
27 AN7/PGED2/RB7 PIC32_PGD2/DBG_SD0 PIC32MX440F512H debug processor
|
|
|
|
|
|
J2 pin 132 (ICSP)
|
|
|
|
|
|
28 PMA7/AERXD2/CVREF-/RA9 PMPA7/VREF-/RA9 J2 pin 113 (PMP address)
|
|
|
|
|
|
J2 pin 114 (A/D ref)
|
|
|
|
|
|
29 PMA6/AERXD3/CVREF+/RA10/VREF+ PMPA6/VREF+/RA10 J2 pin 115 (PMP address)
|
|
|
|
|
|
J2 pin 116 (A/D ref)
|
|
|
|
|
|
30 AVDD P32_VDD ---
|
|
|
|
|
|
31 AVSS (grounded) ---
|
|
|
|
|
|
32 AN8/C1OUT/RB8 C1OUT/AN8/RB8 J2 pin 71
|
|
|
|
|
|
33 AN9/C2OUT/RB9 C2OUT/AN9/RB9 J2 pin 73
|
|
|
|
|
|
34 PMA13/AN10/RB10/CVREFOUT PMPA13/CVREF/AN10 J2 pin 101 (PMP address)
|
|
|
|
|
|
J2 pin 102 (Comparator ref)
|
|
|
|
|
|
35 PMA12/AETXERR/AN11/ERXERR/RB11 PMPA12/AN11/RB11 J2 pin 103 (PMP address)
|
|
|
|
|
|
36 VSS (grounded) ---
|
|
|
|
|
|
37 VDD P32_VDD ---
|
|
|
|
|
|
38 RA1/TCK TCK/RA1 PIC32MX440F512H debug processor
|
|
|
|
|
|
J2 pin 124 (JTAG/GPIO)
|
|
|
|
|
|
39 AC1TX/RF13/SCK4/U2RTS/U5TX SCM3D/BCLK2/RF13 J2 pin 106 (UART2)
|
|
|
|
|
|
40 AC1RX/RF12/SS4/U2CTS/U5RX SCM3C/RF12 J2 pin 108 (UART2)
|
|
|
|
|
|
41 PMA11/AECRS/AN12/ERXD0/RB12 PMPA11/AN12/RB12 J2 pin 105 (PMP address)
|
|
|
|
|
|
42 PMA10/AECOL/AN13/ERXD1/RB13 PMPA10/AN13/RB13 J2 pin 107 (PMP address)
|
|
|
|
|
|
43 PMA1/AETXD3/AN14/ERXD2/PMALH/RB14 PMPA1/AN14/RB14 J2 pin 127 (PMP address)
|
|
|
|
|
|
44 PMA0/AETXD2/AN15/CN12/ERXD3/OCFB/ PMPA0/AN15/OCFB/CN12 J2 pin 129 (PMP address)
|
|
|
|
|
|
PMALL/RB15 J2 pin 36
|
|
|
|
|
|
45 VSS (grounded) ---
|
|
|
|
|
|
46 VDD P32_VDD ---
|
|
|
|
|
|
47 AETXD0/CN20/RD14/SS3/U1CTS/U4RX EXTD0(2) Ethernet TXD_0
|
|
|
|
|
|
48 AETXD1/CN21/RD15/SCK3/U1RTS/U4TX EXTD1(2) Ethernet TXD_1
|
|
|
|
|
|
49 PMA9/CN17/RF4/SDA5/SDI4/U2RX PMPA9/SCM3A/CN17/RF4 J2 pin 109 (PMP address)
|
|
|
|
|
|
J2 pin 110 (UART2)
|
|
|
|
|
|
50 PMA8/CN18/RF5/SCL5/SDO4/U2TX PMPA8/SCM3B/CN18/RF5 J2 pin 111 (PMP address)
|
|
|
|
|
|
J2 pin 112 (UART2)
|
|
|
|
|
|
|
|
|
|
|
|
RIGHT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left)
|
|
|
|
|
|
--- ---------------------------------- -------------------------- -----------------------------------------------
|
|
|
|
|
|
PIN CONFIGURATIONS SIGNAL NAME ON-BOARD CONNECTIONS
|
|
|
|
|
|
(Family Data Sheet Table 1-1) (Starter Kit User Guide)
|
|
|
|
|
|
--- ---------------------------------- -------------------------- -----------------------------------------------
|
|
|
|
|
|
75 VSS (grounded)
|
|
|
|
|
|
74 CN0/RC14/SOSCO/T1CK SOSC0/T1CK/CN0/RC14 32kHz Oscillator, J2 pin (timer)
|
|
|
|
|
|
J2 pin 32 (secondary OSC)
|
|
|
|
|
|
73 CN1/RC13/SOSCI SOSC1/CN1/RC13 32kHz Oscillator
|
|
|
|
|
|
J2 pin 32 (secondary OSC)
|
|
|
|
|
|
72 OC1/INT0/RD0/SDO1 SDO1/INT0/OC1/RD0 User LED D4 (high illuminates)
|
|
|
|
|
|
J2 pin 87 (EXT_INT)
|
|
|
|
|
|
J2 pin 95 (SPI1)
|
|
|
|
|
|
J2 pin 46 (OC/PWM)
|
|
|
|
|
|
71 PMA14/AEMDC/EMDC/IC4/PMCS1/RD11 EMDC Ethernet MDC
|
|
|
|
|
|
70 PMA15/IC3/PMCS2/RD10/SCK1 SCK1/IC3/PMPCS2/RD10 J2 pin 29 (PMP control)
|
|
|
|
|
|
J2 pin 91 (SPI1)
|
|
|
|
|
|
J2 pin 52 (input capture)
|
|
|
|
|
|
69 IC2/RD9/SS1 SS1/IC2/RD9 J2 pin 54 (input capture)
|
|
|
|
|
|
68 AEMDIO/EMDIO/IC1/RD8/RTCC EMDIO Ethernet MDIO
|
|
|
|
|
|
67 AETXEN/INT4/RA15/SDA1 ETXEN(2) Ethernet TX_EN
|
|
|
|
|
|
66 AETXCLK/INT3/RA14/SCL1 INT3/SCL1/RA14 Ethernet PWR_DOWN/INT
|
|
|
|
|
|
65 VSS (grounded) ---
|
|
|
|
|
|
64 CLKO/OSC2/RC15 8MHz crystal
|
|
|
|
|
|
63 CLKI/OSC1/RC12 8MHz crystal
|
|
|
|
|
|
62 VDD P32_VDD ---
|
|
|
|
|
|
61 RA5/TDO TDO/RA5 PIC32MX440F512H debug processor
|
|
|
|
|
|
J2 pin 118 (JTAG/GPIO)
|
|
|
|
|
|
60 RA4/TDI TDI/RA4 PIC32MX440F512H debug processor
|
|
|
|
|
|
59 RA3/SDA2 SDA2/RA3 J2 pin 74 (I2C2)
|
|
|
|
|
|
58 RA2/SCL2 SCL2/RA2 J2 pin 76 (I2C2)
|
|
|
|
|
|
57 D+/RG2 D+/RG2 Host port (J4), Device OTG port (J5)
|
|
|
|
|
|
56 D-/RG3 D-/RG3 Host port (J4), Device OTG port (J5)
|
|
|
|
|
|
55 VUSB P32_VDD ---
|
|
|
|
|
|
54 VBUS P32_VBUS ---
|
|
|
|
|
|
53 RF8/SCL3/SDO3/U1TX SCM1B/RF8 J2 pin 90 (UART1)
|
|
|
|
|
|
52 RF2/SDA3/SDI3/U1RX SCM1A/RF2 J2 pin 88 (UART1)
|
|
|
|
|
|
51 RF3/USBID USBID/RF3 Device OTG port (J5)
|
|
|
|
|
|
|
|
|
|
|
|
TOP SIDE, LEFT-TO-RIGHT (if pin 1 is in upper left)
|
|
|
|
|
|
--- ---------------------------------- -------------------------- -----------------------------------------------
|
|
|
|
|
|
PIN CONFIGURATIONS SIGNAL NAME ON-BOARD CONNECTIONS
|
|
|
|
|
|
(Family Data Sheet Table 1-1) (Starter Kit User Guide)
|
|
|
|
|
|
--- ---------------------------------- -------------------------- -----------------------------------------------
|
|
|
|
|
|
100 PMD4/RE4 PMPD4/RE4 J2 pin 15 (PMP data)
|
|
|
|
|
|
99 PMD3/RE3 PMPD3/RE3 J2 pin 17 (PMP data)
|
|
|
|
|
|
98 PMD2/RE2 PMPD2/RE2 J2 pin 19 (PMP data)
|
|
|
|
|
|
97 RG13/TRD0 TRD0/RG13 J2 pin 8 (Trace/GPIO)
|
|
|
|
|
|
96 RG12/TRD1 TRD1/RG12 J2 pin 5
|
|
|
|
|
|
95 RG14/TRD2 TRD2/RG14 J2 pin 3
|
|
|
|
|
|
94 PMD1/RE1 PMPD1/RE1 J2 pin 21 (PMP data)
|
|
|
|
|
|
93 PMD0/RE0 PMPD0/RE0 J2 pin 23 (PMP data)
|
|
|
|
|
|
92 RA7/TRD3 TRD3/RA7 J2 pin 6 (Trace/GPIO)
|
|
|
|
|
|
91 RA6/TRCLK TRCLK/RA6 J2 pin 4 (Trace/GPIO)
|
|
|
|
|
|
90 PMD8/C2RX/RG0 PMPD8/RG0 J2 pin 10 (PMP data)
|
|
|
|
|
|
89 PMD9/C2TX/ETXERR/RG1 PMPD9/RG1 J2 pin 14 (PMP data)
|
|
|
|
|
|
88 PMD10/C1TX/ETXD0/RF1 PMPD10/RF1 J2 pin 16 (PMP data)
|
|
|
|
|
|
87 PMD11/C1RX/ETXD1/RF0 PMPD11/RF0 J2 pin 18 (PMP data)
|
|
|
|
|
|
86 VDD P32_VDD ---
|
|
|
|
|
|
85 VCAP/VCORE (capacitor to ground) ---
|
|
|
|
|
|
84 PMD15/CN16/ETXCLK/RD7 PMPD15/CN16/RD7 Switch SW2 (low when closed)
|
|
|
|
|
|
J2 pin 26 (PMP data)
|
|
|
|
|
|
83 PMD14/CN15/ETXEN/RD6 PMPD14/CN15/RD6 Switch SW1 (low when closed)
|
|
|
|
|
|
J2 pin 24 (PMP data)
|
|
|
|
|
|
82 CN14/PMRD/RD5 PMPRD/CN14/RD5 J2 pin 25
|
|
|
|
|
|
81 CN13/OC5/PMWR/RD4 PMPWR/OC5/C13/RD4 J2 pin 28 (PMP control)
|
|
|
|
|
|
J2 pin 38
|
|
|
|
|
|
80 PMD13/CN19/ETXD3/RD13 CN19/PMPD13/RD13 Switch SW3 (low when closed)
|
|
|
|
|
|
J2 pin 22 (PMP data)
|
|
|
|
|
|
79 PMD12/ETXD2/IC5/RD12 IC5/PMPD12/RD12 J2 pin 20 (PMP data)
|
|
|
|
|
|
J2 pin 48
|
|
|
|
|
|
78 OC4/RD3 OC4/RD3 J2 pin 40 (OC/PWM)
|
|
|
|
|
|
77 OC3/RD2 OC3/RD2 User LED D5 (high illuminates)
|
|
|
|
|
|
J2 pin 42 (OC/PWM)
|
|
|
|
|
|
76 OC2/RD1 OC1/RD1 User LED D6 (high illuminates)
|
|
|
|
|
|
J2 pin 44 (OC/PWM)
|
|
|
|
|
|
|
|
|
|
|
|
MEB Connector
|
|
|
|
|
|
=============
|
|
|
|
|
|
|
2011-12-23 19:36:34 -04:00
|
|
|
|
The following table summarizes how the pins brought the the MEB through the
|
|
|
|
|
|
J2 on the Ethernet Starter Kit are mapped. This connect is J2 on the Ethernet
|
|
|
|
|
|
Starter Kit and J3 on the MEB.
|
|
|
|
|
|
|
|
|
|
|
|
J3
|
2011-12-19 15:24:09 -04:00
|
|
|
|
PIC32 SIGNAL PIN CONNECTION
|
|
|
|
|
|
-------------------------- ------- ----------------------------------
|
|
|
|
|
|
PMPD0 pin 23 Graphics Controller (SSD1926)
|
|
|
|
|
|
PMPD1 pin 21 8-bit or 16-bit Data Bus
|
|
|
|
|
|
PMPD2 pin 19
|
|
|
|
|
|
PMPD3 pin 17
|
|
|
|
|
|
PMPD4 pin 15
|
|
|
|
|
|
PMPD6 pin 9
|
|
|
|
|
|
PMPD7 pin 7
|
|
|
|
|
|
-------------------------- ------- ----------------------------------
|
|
|
|
|
|
PMPD8 pin 10 Graphics Controller (SSD1926)
|
|
|
|
|
|
PMPD9 pin 14 16-bit Data Bus
|
|
|
|
|
|
PMPD10 pin 16
|
|
|
|
|
|
PMPD11 pin 18
|
|
|
|
|
|
PMPD12 pin 20
|
|
|
|
|
|
PMPD13 pin 22
|
|
|
|
|
|
PMPD14 pin 24
|
|
|
|
|
|
PMPD15 pin 26
|
|
|
|
|
|
-------------------------- ------- ----------------------------------
|
|
|
|
|
|
Graphics Controller (SSD1926)
|
|
|
|
|
|
RG13 pin 8 Chip select
|
|
|
|
|
|
RB10 pin 101 Register select
|
|
|
|
|
|
RC3 pin 39 Wait line
|
|
|
|
|
|
RA10 pin 115 Reset (see MRF24WBOMA and PICtail)
|
|
|
|
|
|
-------------------------- ------- ----------------------------------
|
|
|
|
|
|
Touchscreen
|
|
|
|
|
|
RB11 pin 103 X+
|
|
|
|
|
|
RB12 pin 105 Y-
|
|
|
|
|
|
RB13 pin 107 X-
|
|
|
|
|
|
RB14 pin 127 Y+
|
|
|
|
|
|
-------------------------- ------- ----------------------------------
|
|
|
|
|
|
Joystick
|
|
|
|
|
|
CN2/RB0 pin 72 Left
|
|
|
|
|
|
CN3/RB1 pin 70 Up
|
|
|
|
|
|
CN5/RB3 pin 66 Down
|
|
|
|
|
|
CN6/RB4 pin 64 Right
|
|
|
|
|
|
CN12/RB15 pin 36 Fire
|
|
|
|
|
|
-------------------------- ------- ----------------------------------
|
|
|
|
|
|
LEDs
|
|
|
|
|
|
RD1 pin 44 LED1
|
|
|
|
|
|
RD2 pin 42 LED2
|
|
|
|
|
|
RD3 pin 40 LED3
|
|
|
|
|
|
RC1 pin 35 LED4
|
|
|
|
|
|
RC2 pin 37 LED5
|
|
|
|
|
|
-------------------------- ------- ----------------------------------
|
|
|
|
|
|
SDA2 pin 74 I2C2 bus for BMA150, MCHP24LC08
|
|
|
|
|
|
SCL2 pin 76 and WM8731 (see also MRF24WBOMA)
|
|
|
|
|
|
-------------------------- ------- ----------------------------------
|
|
|
|
|
|
SCK1 pin 91 SPI1 bus for WM8731
|
|
|
|
|
|
SDI1 pin 93
|
|
|
|
|
|
SDO1 pin 95
|
|
|
|
|
|
-------------------------- ------- ----------------------------------
|
|
|
|
|
|
RA6 pin 4 CPLD
|
|
|
|
|
|
RA7 pin 6
|
|
|
|
|
|
RG12 pin 5
|
|
|
|
|
|
RG14 pin 3
|
|
|
|
|
|
SCK2 pin 45 (see MRF24WBOMA)
|
|
|
|
|
|
SDI2 pin 47 (see MRF24WBOMA)
|
|
|
|
|
|
SDO2 pin 49 (see MRF24WBOMA)
|
|
|
|
|
|
RG9 pin 51 (see MRF24WBOMA)
|
|
|
|
|
|
SCK3A pin 106 (see PICtail)
|
|
|
|
|
|
SDI3A pin 110 (see PICtail)
|
|
|
|
|
|
SDO3A pin 112 (see PICtail)
|
|
|
|
|
|
RF12 pin 108 (see PICtail)
|
|
|
|
|
|
~SSI pin 97 (see PICtail)
|
|
|
|
|
|
RD9 pin 54
|
|
|
|
|
|
-------------------------- ------- ----------------------------------
|
|
|
|
|
|
INT3 pin 81 MRF24WBOMA
|
|
|
|
|
|
RA10 pin 115 (also Graphics Controller and PICtail)
|
|
|
|
|
|
RB8 pin 71
|
|
|
|
|
|
-------------------------- ------- ----------------------------------
|
|
|
|
|
|
PICtail J5
|
|
|
|
|
|
SDA2 pin 74 I2C2 bus (see above)
|
|
|
|
|
|
SCL2 pin 76 I2C2 bus (see above)
|
|
|
|
|
|
SCK2 pin 45 (see CPLD)
|
|
|
|
|
|
SDI2 pin 47 (see CPLD)
|
|
|
|
|
|
SDO2 pin 49 (see CPLD)
|
|
|
|
|
|
RG9 pin 51 (see CPLD)
|
|
|
|
|
|
U1RX pin 88
|
|
|
|
|
|
U1TX pin 90
|
|
|
|
|
|
~U1RTS pin 92
|
|
|
|
|
|
~U1CTS pin 94
|
|
|
|
|
|
RB9 pin 73
|
|
|
|
|
|
RA10 pin 115 Reset (see Graphics controller and MRF24WBOMA)
|
|
|
|
|
|
INT1 pin 85
|
|
|
|
|
|
SCL1 pin 84
|
|
|
|
|
|
SDA1 pin 86 (see CPLD)
|
|
|
|
|
|
~SSI pin 97 (see CPLD)
|
|
|
|
|
|
U2RX pin 110 (see CPLD)
|
|
|
|
|
|
U2TX pin 112 (see CPLD)
|
|
|
|
|
|
~U2RTS pin 106 (see CPLD)
|
|
|
|
|
|
~U2CTS pin 108 (see CPLD)
|
|
|
|
|
|
|
2011-12-23 19:36:34 -04:00
|
|
|
|
PICtail
|
|
|
|
|
|
=======
|
|
|
|
|
|
|
|
|
|
|
|
The MEB brings many of the signals out via the PICtail (J5). J5 is
|
|
|
|
|
|
a 28 pin connector bringing out signals as summarized here (J3 is the
|
|
|
|
|
|
designation of the connection to the Ethernet starter kit on the
|
|
|
|
|
|
MEB side):
|
|
|
|
|
|
|
|
|
|
|
|
--- --- ------------------------
|
|
|
|
|
|
J3 J5 Table 2-1
|
|
|
|
|
|
PIN PIN Description
|
|
|
|
|
|
--- --- ------------------------
|
|
|
|
|
|
1 3.3V
|
|
|
|
|
|
2 I/O_4 (Test Point)
|
|
|
|
|
|
76 3 SCL2
|
|
|
|
|
|
84 4 SCL1
|
|
|
|
|
|
74 5 SDA2
|
|
|
|
|
|
86 6 SDA1
|
|
|
|
|
|
47 7 SDI2/SDI2A/CN9/RG7
|
|
|
|
|
|
97 8 SS1, WFI_SDO
|
|
|
|
|
|
49 9 SDO2/SDO2A
|
|
|
|
|
|
10 WFI_SDI
|
|
|
|
|
|
45 11 SCK2/SCK2A
|
|
|
|
|
|
12 WFI_SCK
|
|
|
|
|
|
51 13 SS2/SS2A/RG9
|
|
|
|
|
|
14 SS1/RB2
|
|
|
|
|
|
88 15 U1RX/SDI1A
|
|
|
|
|
|
110 16 U2RX/SDI3A
|
|
|
|
|
|
90 17 U1TX/RA10
|
|
|
|
|
|
112 18 U2TX/SDO3A
|
|
|
|
|
|
92 19 U1RTS/C2OUT/AN9
|
|
|
|
|
|
106 20 U2RTS/SCK3A
|
|
|
|
|
|
94 21 U1CTS/SDO1A
|
|
|
|
|
|
108 22 U2CTS/SS3A/RF12
|
|
|
|
|
|
73 23 RB9/INT1/RE8
|
|
|
|
|
|
115 25 RA10/SCK1A
|
|
|
|
|
|
26 3.3V
|
|
|
|
|
|
85 27 INT1/SS1/RD14
|
|
|
|
|
|
28 GND
|
|
|
|
|
|
|
2011-12-19 15:24:09 -04:00
|
|
|
|
Toolchains
|
|
|
|
|
|
==========
|
|
|
|
|
|
|
|
|
|
|
|
I am using the free, LITE version of the PIC32MX toolchain available
|
|
|
|
|
|
for download from the microchip.com web site. I am using the Windows
|
|
|
|
|
|
version. The MicroChip toolchain is the only toolchaing currently
|
|
|
|
|
|
supported in these configurations, but it should be a simple matter to
|
|
|
|
|
|
adapt to other toolchains by modifying the Make.defs file include in
|
|
|
|
|
|
each configuration.
|
|
|
|
|
|
|
|
|
|
|
|
Toolchain Options:
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_PIC32MX_MICROCHIPW - MicroChip full toolchain for Windows
|
|
|
|
|
|
CONFIG_PIC32MX_MICROCHIPL - MicroChip full toolchain for Linux
|
|
|
|
|
|
CONFIG_PIC32MX_MICROCHIPW_LITE - MicroChip LITE toolchain for Windows
|
|
|
|
|
|
CONFIG_PIC32MX_MICROCHIPL_LITE - MicroChip LITE toolchain for Linux
|
|
|
|
|
|
|
|
|
|
|
|
Windows Native Toolchains
|
|
|
|
|
|
|
|
|
|
|
|
NOTE: There are several limitations to using a Windows based toolchain in a
|
|
|
|
|
|
Cygwin environment. The three biggest are:
|
|
|
|
|
|
|
|
|
|
|
|
1. The Windows toolchain cannot follow Cygwin paths. Path conversions are
|
|
|
|
|
|
performed automatically in the Cygwin makefiles using the 'cygpath' utility
|
|
|
|
|
|
but you might easily find some new path problems. If so, check out 'cygpath -w'
|
|
|
|
|
|
|
|
|
|
|
|
2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links
|
|
|
|
|
|
are used in Nuttx (e.g., include/arch). The make system works around these
|
|
|
|
|
|
problems for the Windows tools by copying directories instead of linking them.
|
|
|
|
|
|
But this can also cause some confusion for you: For example, you may edit
|
|
|
|
|
|
a file in a "linked" directory and find that your changes had no effect.
|
|
|
|
|
|
That is because you are building the copy of the file in the "fake" symbolic
|
|
|
|
|
|
directory. If you use a Windows toolchain, you should get in the habit of
|
|
|
|
|
|
making like this:
|
|
|
|
|
|
|
|
|
|
|
|
make clean_context all
|
|
|
|
|
|
|
|
|
|
|
|
An alias in your .bashrc file might make that less painful.
|
|
|
|
|
|
|
|
|
|
|
|
3. Dependencies are not made when using Windows versions of the GCC. This is
|
|
|
|
|
|
because the dependencies are generated using Windows pathes which do not
|
|
|
|
|
|
work with the Cygwin make.
|
|
|
|
|
|
|
|
|
|
|
|
Support has been added for making dependencies with the windows-native toolchains.
|
|
|
|
|
|
That support can be enabled by modifying your Make.defs file as follows:
|
|
|
|
|
|
|
|
|
|
|
|
- MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
|
|
|
|
|
+ MKDEP = $(TOPDIR)/tools/mkdeps.sh --winpaths "$(TOPDIR)"
|
|
|
|
|
|
|
|
|
|
|
|
If you have problems with the dependency build (for example, if you are not
|
|
|
|
|
|
building on C:), then you may need to modify tools/mkdeps.sh
|
|
|
|
|
|
|
2011-12-24 09:46:06 -04:00
|
|
|
|
Powering the Board
|
|
|
|
|
|
==================
|
|
|
|
|
|
|
2011-12-25 10:28:12 -04:00
|
|
|
|
Ethernet Starter Kit:
|
2011-12-24 09:46:06 -04:00
|
|
|
|
|
2011-12-25 10:28:12 -04:00
|
|
|
|
There are two ways to supply power to the PIC32 Ethernet Starter Kit:
|
2011-12-19 15:24:09 -04:00
|
|
|
|
|
2011-12-25 10:28:12 -04:00
|
|
|
|
- USB bus power connected to USB debug connector J1.
|
|
|
|
|
|
- An external application board with a regulated DC power supply that
|
|
|
|
|
|
provides +5V can be connected to the J2 application board connector
|
|
|
|
|
|
that is provided on the bottom side of the board.
|
2011-12-19 15:24:09 -04:00
|
|
|
|
|
2011-12-25 10:28:12 -04:00
|
|
|
|
One green LED (D3) is provided to show that the PIC32 microcontroller
|
|
|
|
|
|
is powered up.
|
|
|
|
|
|
|
|
|
|
|
|
Ethernet Starter Kit with MEB:
|
|
|
|
|
|
|
|
|
|
|
|
Power can be supplied to the Multimedia Expansion Board through the DC
|
|
|
|
|
|
connector located on the Multimedia Expansion Board... By connecting
|
|
|
|
|
|
9-14V power supply to the DC connector, the Multimedia Expansion Board
|
|
|
|
|
|
and starter kit will receive the proper voltages. The user can also
|
|
|
|
|
|
supply power via the starter kit. However, if the application uses
|
|
|
|
|
|
multiple features of the Multimedia Expansion Board, it is recommended
|
|
|
|
|
|
to use 9-14V power supply."
|
|
|
|
|
|
|
|
|
|
|
|
On Board Debug Support
|
|
|
|
|
|
======================
|
|
|
|
|
|
|
|
|
|
|
|
The PIC32 Ethernet Starter Kit includes a PIC32MX440F512H USB microcontroller
|
|
|
|
|
|
that provides debugger connectivity over USB. The PIC32MX440F512H is hard-wired
|
|
|
|
|
|
to the PIC32 device to provide two types of protocol translation:
|
|
|
|
|
|
|
|
|
|
|
|
- I/O pins of PIC32MX440F512H to the ICSP<53> pins of the PIC32
|
|
|
|
|
|
- I/O pins of PIC32MX440F512H to the JTAG pins of the PIC32
|
|
|
|
|
|
|
|
|
|
|
|
The PIC32 Ethernet Starter Kit currently uses the JTAG pins of the PIC32 device for
|
|
|
|
|
|
programming and debugging.
|
|
|
|
|
|
|
|
|
|
|
|
Creating Compatible NuttX HEX files
|
|
|
|
|
|
===================================
|
|
|
|
|
|
|
|
|
|
|
|
Intel Hex Format Files:
|
|
|
|
|
|
-----------------------
|
2011-12-19 15:24:09 -04:00
|
|
|
|
|
|
|
|
|
|
When NuttX is built it will produce two files in the top-level NuttX
|
|
|
|
|
|
directory:
|
|
|
|
|
|
|
|
|
|
|
|
1) nuttx - This is an ELF file, and
|
|
|
|
|
|
2) nuttx.ihx - This is an Intel Hex format file. This is controlled by
|
|
|
|
|
|
the setting CONFIG_INTELHEX_BINARY in the .config file.
|
|
|
|
|
|
|
|
|
|
|
|
However, there are two problems with the generated nutt.ihx:
|
|
|
|
|
|
|
|
|
|
|
|
1) The tool expects Intel Hex format files to be named *.hex. This
|
|
|
|
|
|
is not a significant issue. However, just renaming the file to
|
|
|
|
|
|
nuttx.hex is *not* sufficient. There is another problem:
|
|
|
|
|
|
2) The tool expects the nuttx.hex file to contain physical addresses.
|
|
|
|
|
|
But the nuttx.ihx file generated from the top-level make will have
|
|
|
|
|
|
address in the KSEG0 and KSEG1 regions.
|
|
|
|
|
|
|
|
|
|
|
|
tools/mkpichex:
|
|
|
|
|
|
---------------
|
|
|
|
|
|
|
|
|
|
|
|
There is a simple tool in the configs/pic32-starterkit/tools directory
|
|
|
|
|
|
that can be used to solve both issues with the nuttx.ihx file. But,
|
|
|
|
|
|
first, you must build the the tools:
|
|
|
|
|
|
|
|
|
|
|
|
cd configs/pic32-starterkit/tools
|
|
|
|
|
|
make
|
|
|
|
|
|
|
|
|
|
|
|
Now you will have an excecutable file call mkpichex (or mkpichex.exe on
|
|
|
|
|
|
Cygwin). This program will take the nutt.ihx file as an input, it will
|
|
|
|
|
|
convert all of the KSEG0 and KSEG1 addresses to physical address, and
|
|
|
|
|
|
it will write the modified file as nuttx.hex.
|
|
|
|
|
|
|
|
|
|
|
|
To use this file, you need to do the following things:
|
|
|
|
|
|
|
|
|
|
|
|
. ./setenv.sh # Source setenv.sh. Among other this, this script
|
|
|
|
|
|
# will add configs/pic32-starterkit/tools to your
|
|
|
|
|
|
# PATH variable
|
|
|
|
|
|
make # Build nuttx and nuttx.ihx
|
|
|
|
|
|
mkpichex $PWD # Convert nuttx.ihx to nuttx.hex. $PWD is the path
|
|
|
|
|
|
# to the top-level build directory. It is the only
|
|
|
|
|
|
# required input to mkpichex.
|
|
|
|
|
|
|
2011-12-23 19:36:34 -04:00
|
|
|
|
Serial Console
|
|
|
|
|
|
==============
|
|
|
|
|
|
|
2011-12-26 16:07:04 -04:00
|
|
|
|
[[Warning: This all sounds great, but the fact is that I have not yet
|
|
|
|
|
|
gotten any serial UART output to work from the MEB.]]
|
|
|
|
|
|
|
2011-12-23 19:36:34 -04:00
|
|
|
|
A serial console is not required to use NuttX. However, all of the
|
|
|
|
|
|
Nuttx example code in the apps/examples assumes that you have a
|
|
|
|
|
|
serial console. The Ethernet Starter Kit(even with the MEB) does not
|
|
|
|
|
|
have any RS-232 connector needed to drive the serial console.
|
|
|
|
|
|
|
|
|
|
|
|
Raw UART signals are available at the MEB's PICtail connector, however,
|
|
|
|
|
|
and can be connected to an external MAX2232 board to get a serial console.
|
|
|
|
|
|
The defconfig files are set up to use UART2. So the proper connections
|
|
|
|
|
|
would be:
|
|
|
|
|
|
|
|
|
|
|
|
PICtail
|
|
|
|
|
|
PIN FUNCTION
|
|
|
|
|
|
-------- -----------
|
|
|
|
|
|
1 3.3V
|
|
|
|
|
|
16 U2RX
|
|
|
|
|
|
18 U2TX
|
|
|
|
|
|
28 GND
|
|
|
|
|
|
|
|
|
|
|
|
UART1 is also brought out on the PICtail and would be connected as:
|
|
|
|
|
|
|
|
|
|
|
|
PICtail
|
|
|
|
|
|
PIN FUNCTION
|
|
|
|
|
|
-------- -----------
|
|
|
|
|
|
1 3.3V
|
|
|
|
|
|
15 U1RX
|
|
|
|
|
|
17 U1TX
|
|
|
|
|
|
28 GND
|
|
|
|
|
|
|
|
|
|
|
|
Here is a summary of the tortuous routes taken by the PIC32MX UART pins:
|
|
|
|
|
|
|
|
|
|
|
|
--- ---------------------------------- -------------------------- -------------------------
|
|
|
|
|
|
PIN CONFIGURATIONS SIGNAL NAME ON-BOARD CONNECTIONS
|
|
|
|
|
|
(Family Data Sheet Table 1-1) (Starter Kit User Guide)
|
|
|
|
|
|
--- ---------------------------------- -------------------------- -------------------------
|
|
|
|
|
|
|
|
|
|
|
|
39 AC1TX/RF13/SCK4/U2RTS/U5TX SCM3D/BCLK2/RF13 J2 pin 106 (UART2)
|
|
|
|
|
|
40 AC1RX/RF12/SS4/U2CTS/U5RX SCM3C/RF12 J2 pin 108 (UART2)
|
|
|
|
|
|
49 PMA9/CN17/RF4/SDA5/SDI4/U2RX PMPA9/SCM3A/CN17/RF4 J2 pin 109 (PMP address)
|
|
|
|
|
|
J2 pin 110 (UART2)
|
|
|
|
|
|
50 PMA8/CN18/RF5/SCL5/SDO4/U2TX PMPA8/SCM3B/CN18/RF5 J2 pin 111 (PMP address)
|
|
|
|
|
|
J2 pin 112 (UART2)
|
|
|
|
|
|
52 RF2/SDA3/SDI3/U1RX SCM1A/RF2 J2 pin 88 (UART1)
|
|
|
|
|
|
53 RF8/SCL3/SDO3/U1TX SCM1B/RF8 J2 pin 90 (UART1)
|
|
|
|
|
|
|
|
|
|
|
|
J2 is the connector at the bottom of the Ethernet start kit that
|
|
|
|
|
|
mates the Ethernet Starter kit to the MEB. The MEB then makes the
|
|
|
|
|
|
following signals available on the PICtail (J5):
|
|
|
|
|
|
|
|
|
|
|
|
MEB Connector:
|
|
|
|
|
|
|
|
|
|
|
|
-------------------------- ------- ----------------------------------
|
|
|
|
|
|
Signal J3
|
|
|
|
|
|
-------------------------- -------
|
|
|
|
|
|
U1RX pin 88
|
|
|
|
|
|
U1TX pin 90
|
|
|
|
|
|
~U1RTS pin 92
|
|
|
|
|
|
~U1CTS pin 94
|
|
|
|
|
|
U2RX pin 110
|
|
|
|
|
|
U2TX pin 112
|
|
|
|
|
|
~U2RTS pin 106
|
|
|
|
|
|
~U2CTS pin 108
|
|
|
|
|
|
-------------------------- -------
|
|
|
|
|
|
|
|
|
|
|
|
PICtail:
|
|
|
|
|
|
|
|
|
|
|
|
The pins are labeled differently in Table 2-1 and in the schematic. This is
|
|
|
|
|
|
confusing. I will trust Table 2-1.
|
|
|
|
|
|
|
|
|
|
|
|
--- --- ------- --- --- -----------------
|
|
|
|
|
|
Table 2-1 Schematic
|
|
|
|
|
|
J3 J5 J3 J5
|
|
|
|
|
|
PIN PIN NAME PIN PIN Description
|
|
|
|
|
|
--- --- ------- ---- --- ------------
|
|
|
|
|
|
1 3.3V
|
|
|
|
|
|
88 15 U1RX 88 15 SDI1A
|
|
|
|
|
|
110 16 U2RX 110 16 SDI3A
|
|
|
|
|
|
90 17 U1TX 17 RA10
|
|
|
|
|
|
90 SD01A
|
|
|
|
|
|
112 18 U2TX 113 18 SDO3A
|
|
|
|
|
|
92 19 U1RTS 19 C2OUT/AN9
|
|
|
|
|
|
92 SCK1A
|
|
|
|
|
|
106 20 U2RTS 106 20 SCK3A
|
|
|
|
|
|
94 21 U1CTS 21 SDO1A
|
|
|
|
|
|
94 SS1/RD14
|
|
|
|
|
|
108 22 U2CTS 108 22 SS3A/RF12
|
|
|
|
|
|
26 3.3V
|
|
|
|
|
|
28 GND
|
|
|
|
|
|
|
2011-12-25 11:56:08 -04:00
|
|
|
|
LEDs
|
|
|
|
|
|
====
|
|
|
|
|
|
|
|
|
|
|
|
The PIC32MX Ethernet Starter kit has 3 user LEDs labeled LED1-3 on the
|
|
|
|
|
|
board graphics (but referred to as LED4-6 in the schematic):
|
|
|
|
|
|
|
|
|
|
|
|
PIN User's Guide Board Stencil Notes
|
|
|
|
|
|
--- ------------- -------------- -------------------------
|
|
|
|
|
|
RD0 "User LED D4" "LED1 (RD0") High illuminates (RED)
|
|
|
|
|
|
RD2 "User LED D5" "LED3 (RD2)" High illuminates (YELLOW)
|
|
|
|
|
|
RD1 "User LED D6" "LED2 (RD1)" High illuminates (GREEN)
|
|
|
|
|
|
|
|
|
|
|
|
We will use the labels on the board to identify LEDs. If CONFIG_ARCH_LEDS
|
|
|
|
|
|
is defined, then NuttX will control these LEDs as follows:
|
|
|
|
|
|
|
|
|
|
|
|
ON OFF
|
|
|
|
|
|
------------------------- ---- ---- ---- ---- ---- ----
|
|
|
|
|
|
LED1 LED2 LED3 LED1 LED2 LED3
|
|
|
|
|
|
------------------------- ---- ---- ---- ---- ---- ----
|
|
|
|
|
|
LED_STARTED 0 OFF OFF OFF --- --- ---
|
|
|
|
|
|
LED_HEAPALLOCATE 1 ON OFF N/C --- --- ---
|
|
|
|
|
|
LED_IRQSENABLED 2 OFF ON N/C --- --- ---
|
|
|
|
|
|
LED_STACKCREATED 3 ON ON N/C --- --- ---
|
|
|
|
|
|
LED_INIRQ 4 N/C N/C ON N/C N/C OFF
|
|
|
|
|
|
LED_SIGNAL 4 N/C N/C ON N/C N/C OFF
|
|
|
|
|
|
LED_ASSERTION 4 N/C N/C ON N/C N/C OFF
|
|
|
|
|
|
LED_PANIC 5 ON N/C N/C OFF N/C N/C
|
|
|
|
|
|
|
|
|
|
|
|
There are 5 additional LEDs available on the MEB. These are not
|
|
|
|
|
|
used by NuttX.
|
|
|
|
|
|
|
|
|
|
|
|
RD1 LED1
|
|
|
|
|
|
RD2 LED2
|
|
|
|
|
|
RD3 LED3
|
|
|
|
|
|
RC1 LED4
|
|
|
|
|
|
RC2 LED5
|
|
|
|
|
|
|
2011-12-19 15:24:09 -04:00
|
|
|
|
PIC32MX Configuration Options
|
|
|
|
|
|
=============================
|
|
|
|
|
|
|
|
|
|
|
|
General Architecture Settings:
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
|
|
|
|
|
|
be set to:
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH=mips
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_family - For use in C code:
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_MIPS=y
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_architecture - For use in C code:
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_MIPS32=y
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_CHIP=pic32mx
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
|
|
|
|
|
|
chip:
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_CHIP_PIC32MX795F512L=y
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
|
|
|
|
|
|
hence, the board that supports the particular chip or SoC.
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_BOARD=pic32-starterkit
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_BOARD_name - For use in C code
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_BOARD_PIC32_STARTERKIT=y
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
|
|
|
|
|
|
of delay loops
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ENDIAN_BIG - define if big endian (default is little
|
|
|
|
|
|
endian)
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_DRAM_SIZE - Describes the installed DRAM (CPU SRAM in this case):
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_DRAM_SIZE=(32*1024) (32Kb)
|
|
|
|
|
|
|
|
|
|
|
|
There is an additional 32Kb of SRAM in AHB SRAM banks 0 and 1.
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_DRAM_START - The start address of installed DRAM
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_DRAM_START=0x10000000
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_DRAM_END - Last address+1 of installed RAM
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_IRQPRIO - The PIC32MXx supports interrupt prioritization
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_IRQPRIO=y
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
|
|
|
|
|
|
have LEDs
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
|
|
|
|
|
stack. If defined, this symbol is the size of the interrupt
|
|
|
|
|
|
stack in bytes. If not defined, the user task stacks will be
|
|
|
|
|
|
used during interrupt handling.
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
|
|
|
|
|
cause a 100 second delay during boot-up. This 100 second delay
|
|
|
|
|
|
serves no purpose other than it allows you to calibratre
|
|
|
|
|
|
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
|
|
|
|
|
|
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
|
|
|
|
|
|
the delay actually is 100 seconds.
|
|
|
|
|
|
|
|
|
|
|
|
PIC32MX Configuration
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_PIC32MX_MVEC - Select muli- vs. single-vectored interrupts
|
|
|
|
|
|
|
|
|
|
|
|
Individual subsystems can be enabled:
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_PIC32MX_WDT - Watchdog timer
|
|
|
|
|
|
CONFIG_PIC32MX_T2 - Timer 2 (Timer 1 is the system time and always enabled)
|
|
|
|
|
|
CONFIG_PIC32MX_T3 - Timer 3
|
|
|
|
|
|
CONFIG_PIC32MX_T4 - Timer 4
|
|
|
|
|
|
CONFIG_PIC32MX_T5 - Timer 5
|
|
|
|
|
|
CONFIG_PIC32MX_IC1 - Input Capture 1
|
|
|
|
|
|
CONFIG_PIC32MX_IC2 - Input Capture 2
|
|
|
|
|
|
CONFIG_PIC32MX_IC3 - Input Capture 3
|
|
|
|
|
|
CONFIG_PIC32MX_IC4 - Input Capture 4
|
|
|
|
|
|
CONFIG_PIC32MX_IC5 - Input Capture 5
|
|
|
|
|
|
CONFIG_PIC32MX_OC1 - Output Compare 1
|
|
|
|
|
|
CONFIG_PIC32MX_OC2 - Output Compare 2
|
|
|
|
|
|
CONFIG_PIC32MX_OC3 - Output Compare 3
|
|
|
|
|
|
CONFIG_PIC32MX_OC4 - Output Compare 4
|
|
|
|
|
|
CONFIG_PIC32MX_OC5 - Output Compare 5
|
|
|
|
|
|
CONFIG_PIC32MX_I2C1 - I2C 1
|
|
|
|
|
|
CONFIG_PIC32MX_I2C2 - I2C 2
|
|
|
|
|
|
CONFIG_PIC32MX_I2C3 - I2C 3
|
|
|
|
|
|
CONFIG_PIC32MX_I2C4 - I2C 4
|
|
|
|
|
|
CONFIG_PIC32MX_I2C5 - I2C 5
|
|
|
|
|
|
CONFIG_PIC32MX_SPI1 - SPI 1
|
|
|
|
|
|
CONFIG_PIC32MX_SPI2 - SPI 2
|
|
|
|
|
|
CONFIG_PIC32MX_SPI3 - SPI 3
|
|
|
|
|
|
CONFIG_PIC32MX_SPI4 - SPI 4
|
|
|
|
|
|
CONFIG_PIC32MX_UART1 - UART 1
|
|
|
|
|
|
CONFIG_PIC32MX_UART2 - UART 2
|
|
|
|
|
|
CONFIG_PIC32MX_UART3 - UART 3
|
|
|
|
|
|
CONFIG_PIC32MX_UART4 - UART 4
|
|
|
|
|
|
CONFIG_PIC32MX_UART5 - UART 5
|
|
|
|
|
|
CONFIG_PIC32MX_UART6 - UART 6
|
|
|
|
|
|
CONFIG_PIC32MX_ADC - ADC 1
|
|
|
|
|
|
CONFIG_PIC32MX_PMP - Parallel Master Port
|
|
|
|
|
|
CONFIG_PIC32MX_CM1 - Comparator 1
|
|
|
|
|
|
CONFIG_PIC32MX_CM2 - Comparator 2
|
|
|
|
|
|
CONFIG_PIC32MX_RTCC - Real-Time Clock and Calendar
|
|
|
|
|
|
CONFIG_PIC32MX_DMA - DMA
|
|
|
|
|
|
CONFIG_PIC32MX_FLASH - FLASH
|
|
|
|
|
|
CONFIG_PIC32MX_USBDEV - USB device
|
|
|
|
|
|
CONFIG_PIC32MX_USBHOST - USB host
|
|
|
|
|
|
CONFIG_PIC32MX_CAN1 - Controller area network 1
|
|
|
|
|
|
CONFIG_PIC32MX_CAN2 - Controller area network 2
|
|
|
|
|
|
CONFIG_PIC32MX_ETHERNET - Ethernet
|
|
|
|
|
|
|
|
|
|
|
|
PIC32MX Configuration Settings
|
|
|
|
|
|
DEVCFG0:
|
|
|
|
|
|
CONFIG_PIC32MX_DEBUGGER - Background Debugger Enable. Default 3 (disabled). The
|
|
|
|
|
|
value 2 enables.
|
|
|
|
|
|
CONFIG_PIC32MX_ICESEL - In-Circuit Emulator/Debugger Communication Channel Select
|
|
|
|
|
|
Default 1 (PG2)
|
|
|
|
|
|
CONFIG_PIC32MX_PROGFLASHWP - Program FLASH write protect. Default 0xff (disabled)
|
|
|
|
|
|
CONFIG_PIC32MX_BOOTFLASHWP - Default 1 (disabled)
|
|
|
|
|
|
CONFIG_PIC32MX_CODEWP - Default 1 (disabled)
|
|
|
|
|
|
DEVCFG1: (All settings determined by selections in board.h)
|
|
|
|
|
|
DEVCFG2: (All settings determined by selections in board.h)
|
|
|
|
|
|
DEVCFG3:
|
|
|
|
|
|
CONFIG_PIC32MX_USBIDO - USB USBID Selection. Default 1 if USB enabled
|
|
|
|
|
|
(USBID pin is controlled by the USB module), but 0 (GPIO) otherwise.
|
|
|
|
|
|
CONFIG_PIC32MX_VBUSIO - USB VBUSON Selection (Default 1 if USB enabled
|
|
|
|
|
|
(VBUSON pin is controlled by the USB module, but 0 (GPIO) otherwise.
|
|
|
|
|
|
CONFIG_PIC32MX_WDENABLE - Enabled watchdog on power up. Default 0 (watchdog
|
|
|
|
|
|
can be enabled later by software).
|
|
|
|
|
|
|
|
|
|
|
|
The priority of interrupts may be specified. The value ranage of
|
|
|
|
|
|
priority is 4-31. The default (16) will be used if these any of these
|
|
|
|
|
|
are undefined.
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_PIC32MX_CTPRIO - Core Timer Interrupt
|
|
|
|
|
|
CONFIG_PIC32MX_CS0PRIO - Core Software Interrupt 0
|
|
|
|
|
|
CONFIG_PIC32MX_CS1PRIO - Core Software Interrupt 1
|
|
|
|
|
|
CONFIG_PIC32MX_INT0PRIO - External Interrupt 0
|
|
|
|
|
|
CONFIG_PIC32MX_INT1PRIO - External Interrupt 1
|
|
|
|
|
|
CONFIG_PIC32MX_INT2PRIO - External Interrupt 2
|
|
|
|
|
|
CONFIG_PIC32MX_INT3PRIO - External Interrupt 3
|
|
|
|
|
|
CONFIG_PIC32MX_INT4PRIO - External Interrupt 4
|
|
|
|
|
|
CONFIG_PIC32MX_FSCMPRIO - Fail-Safe Clock Monitor
|
|
|
|
|
|
CONFIG_PIC32MX_T1PRIO - Timer 1 (System timer) priority
|
|
|
|
|
|
CONFIG_PIC32MX_T2PRIO - Timer 2 priority
|
|
|
|
|
|
CONFIG_PIC32MX_T3PRIO - Timer 3 priority
|
|
|
|
|
|
CONFIG_PIC32MX_T4PRIO - Timer 4 priority
|
|
|
|
|
|
CONFIG_PIC32MX_T5PRIO - Timer 5 priority
|
|
|
|
|
|
CONFIG_PIC32MX_IC1PRIO - Input Capture 1
|
|
|
|
|
|
CONFIG_PIC32MX_IC2PRIO - Input Capture 2
|
|
|
|
|
|
CONFIG_PIC32MX_IC3PRIO - Input Capture 3
|
|
|
|
|
|
CONFIG_PIC32MX_IC4PRIO - Input Capture 4
|
|
|
|
|
|
CONFIG_PIC32MX_IC5PRIO - Input Capture 5
|
|
|
|
|
|
CONFIG_PIC32MX_OC1PRIO - Output Compare 1
|
|
|
|
|
|
CONFIG_PIC32MX_OC2PRIO - Output Compare 2
|
|
|
|
|
|
CONFIG_PIC32MX_OC3PRIO - Output Compare 3
|
|
|
|
|
|
CONFIG_PIC32MX_OC4PRIO - Output Compare 4
|
|
|
|
|
|
CONFIG_PIC32MX_OC5PRIO - Output Compare 5
|
|
|
|
|
|
CONFIG_PIC32MX_I2C1PRIO - I2C 1
|
|
|
|
|
|
CONFIG_PIC32MX_I2C2PRIO - I2C 2
|
|
|
|
|
|
CONFIG_PIC32MX_I2C3PRIO - I2C 3
|
|
|
|
|
|
CONFIG_PIC32MX_I2C4PRIO - I2C 4
|
|
|
|
|
|
CONFIG_PIC32MX_I2C5PRIO - I2C 5
|
|
|
|
|
|
CONFIG_PIC32MX_SPI2PRIO - SPI 2
|
|
|
|
|
|
CONFIG_PIC32MX_UART1PRIO - UART 1
|
|
|
|
|
|
CONFIG_PIC32MX_UART2PRIO - UART 2
|
|
|
|
|
|
CONFIG_PIC32MX_CN - Input Change Interrupt
|
|
|
|
|
|
CONFIG_PIC32MX_ADCPRIO - ADC1 Convert Done
|
|
|
|
|
|
CONFIG_PIC32MX_PMPPRIO - Parallel Master Port
|
|
|
|
|
|
CONFIG_PIC32MX_CM1PRIO - Comparator 1
|
|
|
|
|
|
CONFIG_PIC32MX_CM2PRIO - Comparator 2
|
|
|
|
|
|
CONFIG_PIC32MX_FSCMPRIO - Fail-Safe Clock Monitor
|
|
|
|
|
|
CONFIG_PIC32MX_RTCCPRIO - Real-Time Clock and Calendar
|
|
|
|
|
|
CONFIG_PIC32MX_DMA0PRIO - DMA Channel 0
|
|
|
|
|
|
CONFIG_PIC32MX_DMA1PRIO - DMA Channel 1
|
|
|
|
|
|
CONFIG_PIC32MX_DMA2PRIO - DMA Channel 2
|
|
|
|
|
|
CONFIG_PIC32MX_DMA3PRIO - DMA Channel 3
|
|
|
|
|
|
CONFIG_PIC32MX_DMA4PRIO - DMA Channel 4
|
|
|
|
|
|
CONFIG_PIC32MX_DMA5PRIO - DMA Channel 5
|
|
|
|
|
|
CONFIG_PIC32MX_DMA6PRIO - DMA Channel 6
|
|
|
|
|
|
CONFIG_PIC32MX_DMA7PRIO - DMA Channel 7
|
|
|
|
|
|
CONFIG_PIC32MX_FCEPRIO - Flash Control Event
|
|
|
|
|
|
CONFIG_PIC32MX_USBPRIO - USB
|
|
|
|
|
|
|
2011-12-23 19:36:34 -04:00
|
|
|
|
PIC32MXx specific device driver settings. NOTE: For the Ethernet
|
|
|
|
|
|
starter kit, there is no RS-232 connector (even with the MEB). See
|
|
|
|
|
|
discussion above ("") for information about how you can configure
|
|
|
|
|
|
an external MAX2232 board to get a serial console.
|
2011-12-19 15:24:09 -04:00
|
|
|
|
|
|
|
|
|
|
CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
|
|
|
|
|
console and ttys0 (default is the UART0).
|
|
|
|
|
|
CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
|
|
|
|
|
This specific the size of the receive buffer
|
|
|
|
|
|
CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
|
|
|
|
|
being sent. This specific the size of the transmit buffer
|
|
|
|
|
|
CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
|
|
|
|
|
|
CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
|
|
|
|
|
CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
|
|
|
|
|
CONFIG_UARTn_2STOP - Two stop bits
|
|
|
|
|
|
|
2012-01-08 14:41:49 -04:00
|
|
|
|
PIC32MX specific PHY/Ethernet device driver settings
|
|
|
|
|
|
|
|
|
|
|
|
CONFIG_PHY_KS8721 - Selects the Micrel KS8721 PHY
|
|
|
|
|
|
CONFIG_PHY_DP83848C - Selects the National Semiconduction DP83848C PHY
|
|
|
|
|
|
CONFIG_PHY_LAN8720 - Selects the SMSC LAN8720 PHY
|
|
|
|
|
|
CONFIG_PHY_AUTONEG - Enable auto-negotion
|
|
|
|
|
|
CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed.
|
|
|
|
|
|
CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex
|
2012-01-16 20:00:25 -04:00
|
|
|
|
CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 2
|
|
|
|
|
|
CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 4
|
2012-01-08 14:41:49 -04:00
|
|
|
|
CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is
|
|
|
|
|
|
the higest priority.
|
|
|
|
|
|
CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented).
|
|
|
|
|
|
CONFIG_NET_DUMPPACKET - Dump all received and transmitted packets.
|
|
|
|
|
|
Also needs CONFIG_DEBUG.
|
|
|
|
|
|
CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs
|
|
|
|
|
|
CONFIG_DEBUG.
|
|
|
|
|
|
CONFIG_NET_HASH - Enable receipt of near-perfect match frames.
|
|
|
|
|
|
CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames.
|
|
|
|
|
|
Automatically set if CONFIG_NET_IGMP is selected.
|
|
|
|
|
|
|
|
|
|
|
|
Related DEVCFG3 Configuration Settings:
|
|
|
|
|
|
CONFIG_PIC32MX_FETHIO: Ethernet I/O Pin Selection bit:
|
|
|
|
|
|
1 = Default Ethernet I/O Pins
|
|
|
|
|
|
0 = Alternate Ethernet I/O Pins
|
|
|
|
|
|
CONFIG_PIC32MX_FMIIEN: Ethernet MII Enable bit
|
|
|
|
|
|
1 = MII enabled
|
|
|
|
|
|
0 = RMII enabled
|
|
|
|
|
|
|
2011-12-19 15:24:09 -04:00
|
|
|
|
PIC32MXx USB Device Configuration
|
|
|
|
|
|
|
|
|
|
|
|
PIC32MXx USB Host Configuration (the PIC32MX does not support USB Host)
|
|
|
|
|
|
|
|
|
|
|
|
Configurations
|
|
|
|
|
|
==============
|
|
|
|
|
|
|
|
|
|
|
|
Each PIC32MX configuration is maintained in a sudirectory and can be
|
|
|
|
|
|
selected as follow:
|
|
|
|
|
|
|
|
|
|
|
|
cd tools
|
|
|
|
|
|
./configure.sh pic32-starterkit/<subdir>
|
|
|
|
|
|
cd -
|
|
|
|
|
|
. ./setenv.sh
|
|
|
|
|
|
|
|
|
|
|
|
Where <subdir> is one of the following:
|
|
|
|
|
|
|
|
|
|
|
|
ostest:
|
|
|
|
|
|
This configuration directory, performs a simple OS test using
|
|
|
|
|
|
apps/examples/ostest.
|
