dark0707
/
px4-firmware
forked from Archive/PX4-Autopilot
1
0
Fork 0
Code Pull Requests Activity
px4-firmware/nuttx/configs/hymini-stm32v/README.txt

675 lines
25 KiB
Plaintext
Raw Normal View History

Completes coding of the PWM module git-svn-id: https://nuttx.svn.sourceforge.net/svnroot/nuttx/trunk@4200 7fd9a85b-ad96-42d3-883c-3090e2eb8679
2011-12-19 15:24:09 -04:00
README
======
This README discusses issues unique to NuttX configurations for the
HY-MiniSTM32V development board.
Contents
========
- Development Environment
- GNU Toolchain Options
- IDEs
- NuttX buildroot Toolchain
- DFU
- LEDs
- RTC
- HY-Mini specific Configuration Options
- Configurations
Development Environment
=======================
Either Linux or Cygwin on Windows can be used for the development environment.
The source has been built only using the GNU toolchain (see below). Other
toolchains will likely cause problems. Testing was performed using the Cygwin
environment because the Raisonance R-Link emulatator and some RIDE7 development tools
were used and those tools works only under Windows.
GNU Toolchain Options
=====================
The NuttX make system has been modified to support the following different
toolchain options.
1. The CodeSourcery GNU toolchain,
2. The devkitARM GNU toolchain,
3. Raisonance GNU toolchain, or
4. The NuttX buildroot Toolchain (see below).
All testing has been conducted using the NuttX buildroot toolchain. However,
the make system is setup to default to use the devkitARM toolchain. To use
the CodeSourcery, devkitARM or Raisonance GNU toolchain, you simply need to
add one of the following configuration options to your .config (or defconfig)
file:
CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows
CONFIG_STM32_CODESOURCERYL=y : CodeSourcery under Linux
CONFIG_STM32_DEVKITARM=y : devkitARM under Windows
CONFIG_STM32_RAISONANCE=y : Raisonance RIDE7 under Windows
CONFIG_STM32_BUILDROOT=y : NuttX buildroot under Linux or Cygwin (default)
If you are not using CONFIG_STM32_BUILDROOT, then you may also have to modify
the PATH in the setenv.h file if your make cannot find the tools.
NOTE: the CodeSourcery (for Windows), devkitARM, and Raisonance toolchains are
Windows native toolchains. The CodeSourcey (for Linux) and NuttX buildroot
toolchains are Cygwin and/or Linux native toolchains. There are several limitations
to using a Windows based toolchain in a Cygwin environment. The three biggest are:
1. The Windows toolchain cannot follow Cygwin paths. Path conversions are
performed automatically in the Cygwin makefiles using the 'cygpath' utility
but you might easily find some new path problems. If so, check out 'cygpath -w'
2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links
are used in Nuttx (e.g., include/arch). The make system works around these
problems for the Windows tools by copying directories instead of linking them.
But this can also cause some confusion for you: For example, you may edit
a file in a "linked" directory and find that your changes had no effect.
That is because you are building the copy of the file in the "fake" symbolic
directory. If you use a Windows toolchain, you should get in the habit of
making like this:
make clean_context all
An alias in your .bashrc file might make that less painful.
3. Dependencies are not made when using Windows versions of the GCC. This is
because the dependencies are generated using Windows pathes which do not
work with the Cygwin make.
Support has been added for making dependencies with the windows-native toolchains.
That support can be enabled by modifying your Make.defs file as follows:
- MKDEP = $(TOPDIR)/tools/mknulldeps.sh
+ MKDEP = $(TOPDIR)/tools/mkdeps.sh --winpaths "$(TOPDIR)"
If you have problems with the dependency build (for example, if you are not
building on C:), then you may need to modify tools/mkdeps.sh
NOTE 1: The CodeSourcery toolchain (2009q1) does not work with default optimization
level of -Os (See Make.defs). It will work with -O0, -O1, or -O2, but not with
-Os.
NOTE 2: The devkitARM toolchain includes a version of MSYS make. Make sure that
the paths to Cygwin's /bin and /usr/bin directories appear BEFORE the devkitARM
path or will get the wrong version of make.
IDEs
====
NuttX is built using command-line make. It can be used with an IDE, but some
effort will be required to create the project (There is a simple RIDE project
in the RIDE subdirectory).
Makefile Build
--------------
Under Eclipse, it is pretty easy to set up an "empty makefile project" and
simply use the NuttX makefile to build the system. That is almost for free
under Linux. Under Windows, you will need to set up the "Cygwin GCC" empty
makefile project in order to work with Windows (Google for "Eclipse Cygwin" -
there is a lot of help on the internet).
Native Build
------------
Here are a few tips before you start that effort:
1) Select the toolchain that you will be using in your .config file
2) Start the NuttX build at least one time from the Cygwin command line
before trying to create your project. This is necessary to create
certain auto-generated files and directories that will be needed.
3) Set up include pathes: You will need include/, arch/arm/src/stm32,
arch/arm/src/common, arch/arm/src/armv7-m, and sched/.
4) All assembly files need to have the definition option -D __ASSEMBLY__
on the command line.
Startup files will probably cause you some headaches. The NuttX startup file
is arch/arm/src/stm32/stm32_vectors.S. With RIDE, I have to build NuttX
one time from the Cygwin command line in order to obtain the pre-built
startup object needed by RIDE.
NuttX buildroot Toolchain
=========================
A GNU GCC-based toolchain is assumed. The files */setenv.sh should
be modified to point to the correct path to the Cortex-M3 GCC toolchain (if
different from the default in your PATH variable).
If you have no Cortex-M3 toolchain, one can be downloaded from the NuttX
SourceForge download site (https://sourceforge.net/project/showfiles.php?group_id=189573).
This GNU toolchain builds and executes in the Linux or Cygwin environment.
1. You must have already configured Nuttx in <some-dir>/nuttx.
cd tools
./configure.sh hymini-stm32v/<sub-dir>
2. Download the latest buildroot package into <some-dir>
3. unpack the buildroot tarball. The resulting directory may
have versioning information on it like buildroot-x.y.z. If so,
rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.
4. cd <some-dir>/buildroot
5. cp configs/cortexm3-defconfig-4.3.3 .config
6. make oldconfig
7. make
8. Edit setenv.h, if necessary, so that the PATH variable includes
the path to the newly built binaries.
See the file configs/README.txt in the buildroot source tree. That has more
detailed PLUS some special instructions that you will need to follow if you are
building a Cortex-M3 toolchain for Cygwin under Windows.
DFU
===
The linker files in these projects can be configured to indicate that you
will be loading code using STMicro built-in USB Device Firmware Upgrade (DFU)
loader or via some JTAG emulator. You can specify the DFU bootloader by
adding the following line:
CONFIG_STM32_DFU=y
to your .config file. Most of the configurations in this directory are set
up to use the DFU loader.
If CONFIG_STM32_DFU is defined, the code will not be positioned at the beginning
of FLASH (0x08000000) but will be offset to 0x08003000. This offset is needed
to make space for the DFU loader and 0x08003000 is where the DFU loader expects
to find new applications at boot time. If you need to change that origin for some
other bootloader, you will need to edit the file(s) ld.script.dfu for each
configuration.
The DFU SE PC-based software is available from the STMicro website,
http://www.st.com. General usage instructions:
1. Convert the NuttX Intel Hex file (nuttx.ihx) into a special DFU
file (nuttx.dfu)... see below for details.
2. Connect the Hy-Mini STM32v board to your computer using a USB
cable.
3. Start the DFU loader on the Hy-Mini STM32v board. You do this by
resetting the board while holding the "Key" button. Windows should
recognize that the DFU loader has been installed.
3. Run the DFU SE program to load nuttx.dfu into FLASH.
What if the DFU loader is not in FLASH? The loader code is available
inside of the Demo dirctory of the USBLib ZIP file that can be downloaded
from the STMicro Website. You can build it using RIDE (or other toolchains);
you will need a JTAG emulator to burn it into FLASH the first time.
In order to use STMicro's built-in DFU loader, you will have to get
the NuttX binary into a special format with a .dfu extension. The
DFU SE PC_based software installation includes a file "DFU File Manager"
conversion program that a file in Intel Hex format to the special DFU
format. When you successfully build NuttX, you will find a file called
nutt.ihx in the top-level directory. That is the file that you should
provide to the DFU File Manager. You will need to rename it to nuttx.hex
in order to find it with the DFU File Manager. You will end up with
a file called nuttx.dfu that you can use with the STMicro DFU SE program.
LEDs
====
The HY-MiniSTM32 board provides only two controlable LEDs labeled LED1 and LED2.
Usage of these LEDs is defined in include/board.h and src/up_leds.c.
They are encoded as follows:
SYMBOL Meaning LED1* LED2
------------------- ----------------------- ------- -------
LED_STARTED NuttX has been started OFF OFF
LED_HEAPALLOCATE Heap has been allocated ON OFF
LED_IRQSENABLED Interrupts enabled OFF ON
LED_STACKCREATED Idle stack created ON OFF
LED_INIRQ In an interrupt** OFF N/C
LED_SIGNAL In a signal handler*** N/C ON
LED_ASSERTION An assertion failed ON ON
LED_PANIC The system has crashed BLINK BLINK
LED_IDLE STM32 is is sleep mode (Optional, not used)
* If Nuttx starts correctly, normal state is to have LED1 on and LED2 off.
** LED1 is turned off during interrrupt.
*** LED2 is turned on during signal handler.
RTC
===
The STM32 RTC may configured using the following settings.
CONFIG_RTC - Enables general support for a hardware RTC. Specific
architectures may require other specific settings.
CONFIG_RTC_HIRES - The typical RTC keeps time to resolution of 1
second, usually supporting a 32-bit time_t value. In this case,
the RTC is used to &quot;seed&quot; the normal NuttX timer and the
NuttX timer provides for higher resoution time. If CONFIG_RTC_HIRES
is enabled in the NuttX configuration, then the RTC provides higher
resolution time and completely replaces the system timer for purpose of
date and time.
CONFIG_RTC_FREQUENCY - If CONFIG_RTC_HIRES is defined, then the
frequency of the high resolution RTC must be provided. If CONFIG_RTC_HIRES
is not defined, CONFIG_RTC_FREQUENCY is assumed to be one.
CONFIG_RTC_ALARM - Enable if the RTC hardware supports setting of an alarm.
A callback function will be executed when the alarm goes off
In hi-res mode, the STM32 RTC operates only at 16384Hz. Overflow interrupts
are handled when the 32-bit RTC counter overflows every 3 days and 43 minutes.
A BKP register is incremented on each overflow interrupt creating, effectively,
a 48-bit RTC counter.
In the lo-res mode, the RTC operates at 1Hz. Overflow interrupts are not handled
(because the next overflow is not expected until the year 2106.
WARNING: Overflow interrupts are lost whenever the STM32 is powered down. The
overflow interrupt may be lost even if the STM32 is powered down only momentarily.
Therefore hi-res solution is only useful in systems where the power is always on.
HY-Mini specific Configuration Options
============================================
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
be set to:
CONFIG_ARCH=arm
CONFIG_ARCH_family - For use in C code:
CONFIG_ARCH_ARM=y
CONFIG_ARCH_architecture - For use in C code:
CONFIG_ARCH_CORTEXM3=y
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
CONFIG_ARCH_CHIP=stm32
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
chip:
CONFIG_ARCH_CHIP_STM32F103VCT6
CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG - Enables special STM32 clock
configuration features.
CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG=n
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
hence, the board that supports the particular chip or SoC.
CONFIG_ARCH_BOARD=hymini-stm32v (for the HY-Mini development board)
CONFIG_ARCH_BOARD_name - For use in C code
CONFIG_ARCH_BOARD_HYMINI_STM32V=y
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
of delay loops
CONFIG_ENDIAN_BIG - define if big endian (default is little
endian)
CONFIG_DRAM_SIZE - Describes the installed DRAM (SRAM in this case):
CONFIG_DRAM_SIZE=0x0000C000 (48Kb)
CONFIG_DRAM_START - The start address of installed DRAM
CONFIG_DRAM_START=0x20000000
CONFIG_DRAM_END - Last address+1 of installed RAM
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
CONFIG_ARCH_IRQPRIO - The STM32F103V supports interrupt prioritization
CONFIG_ARCH_IRQPRIO=y
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
have LEDs
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
stack. If defined, this symbol is the size of the interrupt
stack in bytes. If not defined, the user task stacks will be
used during interrupt handling.
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
cause a 100 second delay during boot-up. This 100 second delay
serves no purpose other than it allows you to calibratre
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
the delay actually is 100 seconds.
Individual subsystems can be enabled:
AHB
---
CONFIG_STM32_DMA1
CONFIG_STM32_DMA2
CONFIG_STM32_CRC
CONFIG_STM32_FSMC
CONFIG_STM32_SDIO
APB1
----
CONFIG_STM32_TIM2
CONFIG_STM32_TIM3 (required for PWM control of LCD backlight)
CONFIG_STM32_TIM4
CONFIG_STM32_TIM5
CONFIG_STM32_TIM6
CONFIG_STM32_TIM7
CONFIG_STM32_WWDG
CONFIG_STM32_SPI2
CONFIG_STM32_SPI4
CONFIG_STM32_USART2
CONFIG_STM32_USART3
CONFIG_STM32_UART4
CONFIG_STM32_UART5
CONFIG_STM32_I2C1
CONFIG_STM32_I2C2
CONFIG_STM32_USB
CONFIG_STM32_CAN
CONFIG_STM32_BKP
CONFIG_STM32_PWR
CONFIG_STM32_DAC
CONFIG_STM32_USB
APB2
----
CONFIG_STM32_ADC1
CONFIG_STM32_ADC2
CONFIG_STM32_TIM1
CONFIG_STM32_SPI1
CONFIG_STM32_TIM8
CONFIG_STM32_USART1
CONFIG_STM32_ADC3
Timer and I2C devices may need to the following to force power to be applied
unconditionally at power up. (Otherwise, the device is powered when it is
initialized).
CONFIG_STM32_FORCEPOWER
The Timer3 alternate mapping is required for PWM control of LCD backlight
CONFIG_STM32_TIM3_PARTIAL_REMAP=y
Timer devices may be used for different purposes. One special purpose is
to generate modulated outputs for such things as motor control. If CONFIG_STM32_TIMn
is defined (as above) then the following may also be defined to indicate that
the timer is intended to be used for pulsed output modulation, ADC conversion,
or DAC conversion.
CONFIG_STM32_TIM1_PWM
CONFIG_STM32_TIM2_PWM
CONFIG_STM32_TIM3_PWM
CONFIG_STM32_TIM4_PWM
CONFIG_STM32_TIM5_PWM
CONFIG_STM32_TIM6_PWM
CONFIG_STM32_TIM7_PWM
CONFIG_STM32_TIM8_PWM
CONFIG_STM32_TIM1_ADC
CONFIG_STM32_TIM2_ADC
CONFIG_STM32_TIM3_ADC
CONFIG_STM32_TIM4_ADC
CONFIG_STM32_TIM5_ADC
CONFIG_STM32_TIM6_ADC
CONFIG_STM32_TIM7_ADC
CONFIG_STM32_TIM8_ADC
CONFIG_STM32_TIM1_DAC
CONFIG_STM32_TIM2_DAC
CONFIG_STM32_TIM3_DAC
CONFIG_STM32_TIM4_DAC
CONFIG_STM32_TIM5_DAC
CONFIG_STM32_TIM6_DAC
CONFIG_STM32_TIM7_DAC
CONFIG_STM32_TIM8_DAC
Others alternate pin mappings available:
CONFIG_STM32_TIM1_FULL_REMAP
CONFIG_STM32_TIM1_PARTIAL_REMAP
CONFIG_STM32_TIM2_FULL_REMAP
CONFIG_STM32_TIM2_PARTIAL_REMAP_1
CONFIG_STM32_TIM2_PARTIAL_REMAP_2
CONFIG_STM32_TIM3_FULL_REMAP
CONFIG_STM32_TIM3_PARTIAL_REMAP
CONFIG_STM32_TIM4_REMAP
CONFIG_STM32_USART1_REMAP
CONFIG_STM32_USART2_REMAP
CONFIG_STM32_USART3_FULL_REMAP
CONFIG_STM32_USART3_PARTIAL_REMAP
CONFIG_STM32_SPI1_REMAP
CONFIG_STM32_SPI3_REMAP
CONFIG_STM32_I2C1_REMAP
CONFIG_STM32_CAN1_FULL_REMAP
CONFIG_STM32_CAN1_PARTIAL_REMAP
CONFIG_STM32_CAN2_REMAP
STM32F103V specific device driver settings
CONFIG_U[S]ARTn_SERIAL_CONSOLE - selects the USARTn (n=1,2,3) or UART
m (m=4,5) for the console and ttys0 (default is the USART1).
Note: USART1 is connected to a PL2303 serial to USB converter.
So USART1 is available through USB port labeled CN3 on the board.
CONFIG_U[S]ARTn_RXBUFSIZE - Characters are buffered as received.
This specific the size of the receive buffer
CONFIG_U[S]ARTn_TXBUFSIZE - Characters are buffered before
being sent. This specific the size of the transmit buffer
CONFIG_U[S]ARTn_BAUD - The configure BAUD of the UART. Must be
CONFIG_U[S]ARTn_BITS - The number of bits. Must be either 7 or 8.
CONFIG_U[S]ARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
CONFIG_U[S]ARTn_2STOP - Two stop bits
CONFIG_STM32_SPI_INTERRUPTS - Select to enable interrupt driven SPI
support. Non-interrupt-driven, poll-waiting is recommended if the
interrupt rate would be to high in the interrupt driven case.
CONFIG_STM32_SPI_DMA - Use DMA to improve SPI transfer performance.
Cannot be used with CONFIG_STM32_SPI_INTERRUPT.
CONFIG_SDIO_DMA - Support DMA data transfers. Requires CONFIG_STM32_SDIO
and CONFIG_STM32_DMA2.
CONFIG_SDIO_PRI - Select SDIO interrupt prority. Default: 128
CONFIG_SDIO_DMAPRIO - Select SDIO DMA interrupt priority.
Default: Medium
CONFIG_SDIO_WIDTH_D1_ONLY - Select 1-bit transfer mode. Default:
4-bit transfer mode.
CONFIG_MMCSD_HAVECARDDETECT - Select if SDIO driver card detection
is 100% accurate (it is on the HY-MiniSTM32V)
HY-MiniSTM32V LCD Hardware Configuration (SSD1289 controler)
CONFIG_NX_LCDDRIVER - To be defined to include LCD driver
CONFIG_LCD_LANDSCAPE - Define for 320x240 display "landscape"
support. In this orientation, the HY-MiniSTM32V's
LCD used connector is at the right of the display.
Default is this 320x240 "landscape" orientation
CONFIG_LCD_PORTRAIT - Define for 240x320 display "portrait"
orientation support. In this orientation, the HY-MiniSTM32V's
LCD used connector is at the bottom of the display. Default is
320x240 "landscape" orientation.
CONFIG_LCD_RPORTRAIT - Define for 240x320 display "reverse
portrait" orientation support. In this orientation, the
HY-MiniSTM32V's LCD used connector is at the top of the display.
Default is 320x240 "landscape" orientation.
CONFIG_LCD_BACKLIGHT - Define to support an adjustable backlight
using timer 3. The granularity of the settings is determined
by CONFIG_LCD_MAXPOWER. Requires CONFIG_STM32_TIM3.
Configurations
==============
Each HY-MiniSTM32V configuration is maintained in a sudirectory and
can be selected as follow:
cd tools
./configure.sh hymini-stm32v/<subdir>
cd -
. ./setenv.sh
Where <subdir> is one of the following:
buttons:
--------
Uses apps/examples/buttons to exercise HY-MiniSTM32V buttons and
button interrupts.
CONFIG_STM32_CODESOURCERYL=y : CodeSourcery under Linux
nsh and nsh2:
------------
Configure the NuttShell (nsh) located at examples/nsh.
Differences between the two NSH configurations:
=========== ======================= ================================
nsh nsh2
=========== ======================= ================================
Toolchain: Codesourcery for Linux Codesourcery for Linux (1)
----------- ----------------------- --------------------------------
Loader: ST bootloader ST bootloader
----------- ----------------------- --------------------------------
Serial Debug output: USART1 Debug output: USART1
Console: NSH output: USART1 NSH output: USART1 (3)
----------- ----------------------- --------------------------------
microSD Yes Yes
Support
----------- ----------------------- --------------------------------
FAT FS CONFIG_FAT_LCNAME=y CONFIG_FAT_LCNAME=y
Config CONFIG_FAT_LFN=n CONFIG_FAT_LFN=y (4)
----------- ----------------------- --------------------------------
LCD Driver No Yes
Support
----------- ----------------------- --------------------------------
RTC Support No Yes
----------- ----------------------- --------------------------------
Support for No Yes
Built-in
Apps
----------- ----------------------- --------------------------------
Built-in None apps/examples/nx
Apps apps/examples/nxhello
apps/examples/usbstorage (5)
apps/examples/buttons
apps/examples/nximage
=========== ======================= ================================
(1) You will probably need to modify nsh/setenv.sh or nsh2/setenv.sh
to set up the correct PATH variable for whichever toolchain you
may use.
(2) Since DfuSe is assumed, this configuration may only work under
Cygwin without modification.
(3) When any other device other than /dev/console is used for a user
interface, (1) linefeeds (\n) will not be expanded to carriage return
/ linefeeds \r\n). You will need to configure your terminal program
to account for this. And (2) input is not automatically echoed so
you will have to turn local echo on.
(4) Microsoft holds several patents related to the design of
long file names in the FAT file system. Please refer to the
details in the top-level COPYING file. Please do not use FAT
long file name unless you are familiar with these patent issues.
(5) When built as an NSH add-on command (CONFIG_EXAMPLES_USBSTRG_BUILTIN=y),
Caution should be used to assure that the SD drive is not in use when
the USB storage device is configured. Specifically, the SD driver
should be unmounted like:
nsh> mount -t vfat /dev/mmcsd0 /mnt/sdcard # Card is mounted in NSH
...
nsh> umount /mnd/sdcard # Unmount before connecting USB!!!
nsh> msconn # Connect the USB storage device
...
nsh> msdis # Disconnect USB storate device
nsh> mount -t vfat /dev/mmcsd0 /mnt/sdcard # Restore the mount
Failure to do this could result in corruption of the SD card format.
nx:
---
An example using the NuttX graphics system (NX). This example
focuses on general window controls, movement, mouse and keyboard
input.
CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows
CONFIG_LCD_RPORTRAIT=y : 240x320 reverse portrait
nxlines:
------
Another example using the NuttX graphics system (NX). This
example focuses on placing lines on the background in various
orientations.
CONFIG_STM32_CODESOURCERYL=y : CodeSourcery under Linux
CONFIG_LCD_RPORTRAIT=y : 240x320 reverse portrait
usbserial:
---------
This configuration directory exercises the USB serial class
driver at examples/usbserial. See examples/README.txt for
more information.
CONFIG_STM32_CODESOURCERYL=y : CodeSourcery under Linux
USB debug output can be enabled as by changing the following
settings in the configuration file:
-CONFIG_DEBUG=n
-CONFIG_DEBUG_VERBOSE=n
-CONFIG_DEBUG_USB=n
+CONFIG_DEBUG=y
+CONFIG_DEBUG_VERBOSE=y
+CONFIG_DEBUG_USB=y
-CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
-CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
-CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
-CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
-CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
+CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=y
+CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=y
+CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=y
+CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=y
+CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=y
By default, the usbserial example uses the Prolific PL2303
serial/USB converter emulation. The example can be modified
to use the CDC/ACM serial class by making the following changes
to the configuration file:
-CONFIG_USBSER=y
+CONFIG_USBSER=n
-CONFIG_CDCSER=n
+CONFIG_CDCSER=y
The example can also be converted to use the alternative
USB serial example at apps/examples/usbterm by changing the
following:
-CONFIGURED_APPS += examples/usbserial
+CONFIGURED_APPS += examples/usbterm
In either the original appconfig file (before configuring)
or in the final apps/.config file (after configuring).
usbstorage:
----------
This configuration directory exercises the USB mass storage
class driver at examples/usbstorage. See examples/README.txt for
more information.
CONFIG_STM32_CODESOURCERYL=y : CodeSourcery under Linux