c273b23940
this moves the key MCU config variables related to memory to the python MCU database, allowing the hwdef.dat to be considerably simpler
137 lines
2.8 KiB
Plaintext
137 lines
2.8 KiB
Plaintext
# hw definition file for processing by chibios_pins.py
|
|
# for Revo-Mini hardware
|
|
|
|
# MCU class and specific type
|
|
MCU STM32F4xx STM32F405xx
|
|
|
|
define CONFIG_HAL_BOARD_SUBTYPE HAL_BOARD_SUBTYPE_CHIBIOS_REVOMINI
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 70
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 8000000
|
|
STM32_PLLM_VALUE 8
|
|
|
|
define STM32_ST_USE_TIMER 5
|
|
|
|
FLASH_SIZE_KB 1024
|
|
|
|
# board voltage
|
|
STM32_VDD 330U
|
|
|
|
STDOUT_SERIAL SD3
|
|
STDOUT_BAUDRATE 57600
|
|
|
|
# only one I2C bus
|
|
I2C_ORDER I2C1
|
|
|
|
# order of UARTs (and USB)
|
|
UART_ORDER OTG1 USART3 USART1
|
|
|
|
# rcinput is PC6, which is the 3rd "PWM IN" pin (the yellow wire on a
|
|
# revolution board)
|
|
PC6 TIM8_CH1 TIM8 RCIN FLOAT LOW
|
|
|
|
# analog pins
|
|
PC3 VDD_5V_SENS ADC1
|
|
PC2 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
PC1 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
PC5 USB_SENSE ADC1
|
|
|
|
# define default battery setup
|
|
define HAL_BATT_VOLT_PIN 12
|
|
define HAL_BATT_CURR_PIN 11
|
|
define HAL_BATT_VOLT_SCALE 10.1
|
|
define HAL_BATT_CURR_SCALE 17.0
|
|
|
|
|
|
PC0 SBUS_INVERT OUTPUT LOW
|
|
|
|
# LEDs
|
|
PB5 LED_BLUE OUTPUT LOW GPIO(0)
|
|
PB6 LED_YELLOW OUTPUT LOW GPIO(1) # optional
|
|
PB4 LED_RED OUTPUT LOW GPIO(2)
|
|
|
|
# GPS port disabled (PC6 used for RCIN)
|
|
#PC6 USART6_TX USART6
|
|
#PC7 USART6_RX USART6
|
|
|
|
# flexi port, setup as GPS
|
|
PB10 USART3_TX USART3
|
|
PB11 USART3_RX USART3
|
|
|
|
# main port, for telem1
|
|
PA9 USART1_TX USART1
|
|
PA10 USART1_RX USART1
|
|
|
|
# alternative config
|
|
# PB10 I2C2_SCL I2C2
|
|
# PB11 I2C2_SDA I2C2
|
|
|
|
# spi bus for IMU
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
# spi bus for dataflash
|
|
PC10 SPI3_SCK SPI3
|
|
PC11 SPI3_MISO SPI3
|
|
PC12 SPI3_MOSI SPI3
|
|
|
|
# IRQ for MPU6000
|
|
PC4 EXTI_MPU6000 INPUT
|
|
|
|
# PA10 IO-debug-console
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# only one I2C bus in normal config
|
|
PB8 I2C1_SCL I2C1
|
|
PB9 I2C1_SDA I2C1
|
|
|
|
# SPI chip selects
|
|
PA4 MPU_CS CS
|
|
PB3 FLASH_CS CS
|
|
|
|
# PWM out pins
|
|
PB0 TIM3_CH3 TIM3 PWM(1) GPIO(50)
|
|
PB1 TIM3_CH4 TIM3 PWM(2) GPIO(51)
|
|
PA3 TIM2_CH4 TIM2 PWM(3) GPIO(52)
|
|
PA2 TIM2_CH3 TIM2 PWM(4) GPIO(53)
|
|
PA1 TIM2_CH2 TIM2 PWM(5) GPIO(54)
|
|
PA0 TIM2_CH1 TIM2 PWM(6) GPIO(55)
|
|
PC8 TIM8_CH3 TIM2 PWM(7) GPIO(56)
|
|
PC9 TIM8_CH4 TIM2 PWM(8) GPIO(57)
|
|
|
|
PB7 DRDY_HMC5883 INPUT PULLUP
|
|
|
|
define HAL_STORAGE_SIZE 8192
|
|
define STORAGE_FLASH_PAGE 1
|
|
|
|
# reserve 16k for bootloader, 16k for OSD and 32k for flash storage
|
|
FLASH_RESERVE_START_KB 64
|
|
|
|
define HAL_INS_DEFAULT HAL_INS_MPU60XX_SPI
|
|
define HAL_INS_DEFAULT_ROTATION ROTATION_YAW_180
|
|
|
|
define HAL_COMPASS_DEFAULT HAL_COMPASS_HMC5843
|
|
define HAL_COMPASS_HMC5843_I2C_BUS 0
|
|
define HAL_COMPASS_HMC5843_I2C_ADDR 0x1E
|
|
define HAL_COMPASS_HMC5843_ROTATION ROTATION_YAW_90
|
|
|
|
define HAL_BARO_DEFAULT HAL_BARO_MS5611_I2C
|
|
define HAL_BARO_MS5611_I2C_BUS 0
|
|
define HAL_BARO_MS5611_I2C_ADDR 0x77
|
|
|
|
# SPI devices
|
|
SPIDEV mpu6000 SPI1 DEVID1 MPU_CS MODE3 1*MHZ 8*MHZ
|
|
SPIDEV dataflash SPI3 DEVID1 FLASH_CS MODE3 1*MHZ 8*MHZ
|
|
|
|
# 8 PWM available by default
|
|
define BOARD_PWM_COUNT_DEFAULT 8
|
|
|