185 lines
5.0 KiB
C
185 lines
5.0 KiB
C
#ifndef _BOARD_STM32V1F4_H_
|
|
#define _BOARD_STM32V1F4_H_
|
|
|
|
|
|
|
|
/**
|
|
* @brief Configuration of the Cortex-M4 Processor and Core Peripherals
|
|
*/
|
|
#define __CM4_REV 0x0001 /*!< Core revision r0p1 */
|
|
#define __MPU_PRESENT 1 /*!< STM32F4XX provides an MPU */
|
|
#define __NVIC_PRIO_BITS 4 /*!< STM32F4XX uses 4 Bits for the Priority Levels */
|
|
#define __Vendor_SysTickConfig 0 /*!< Set to 1 if different SysTick Config is used */
|
|
#define __FPU_PRESENT 1 /*!< FPU present */
|
|
|
|
#define HSE_VALUE (8000000)
|
|
|
|
#define CYCLES_PER_MICROSECOND (SystemCoreClock / 1000000)
|
|
#define SYSTICK_RELOAD_VAL (CYCLES_PER_MICROSECOND*1000-1)
|
|
|
|
#undef STM32_PCLK1
|
|
#undef STM32_PCLK2
|
|
#define STM32_PCLK1 (CYCLES_PER_MICROSECOND*1000000/4)
|
|
#define STM32_PCLK2 (CYCLES_PER_MICROSECOND*1000000/2)
|
|
|
|
#define BOARD_BUTTON_PIN 254
|
|
|
|
#ifndef LOW
|
|
# define LOW 0
|
|
#endif
|
|
#ifndef HIGH
|
|
# define HIGH 1
|
|
#endif
|
|
|
|
//#define BOARD_BUZZER_PIN 5 // PB15, PWM2 - used as PPM2
|
|
|
|
|
|
#define BOARD_NR_USARTS 5
|
|
#define BOARD_USART1_TX_PIN 23
|
|
#define BOARD_USART1_RX_PIN 24
|
|
#define BOARD_USART3_TX_PIN 0
|
|
#define BOARD_USART3_RX_PIN 100
|
|
#define BOARD_USART6_TX_PIN 12
|
|
#define BOARD_USART6_RX_PIN 13
|
|
|
|
#define BOARD_DSM_USART (_USART1)
|
|
|
|
#define BOARD_NR_SPI 3
|
|
#define BOARD_SPI1_SCK_PIN 52
|
|
#define BOARD_SPI1_MISO_PIN 53
|
|
#define BOARD_SPI1_MOSI_PIN 54
|
|
#define BOARD_SPI2_SCK_PIN 3 // PB13
|
|
#define BOARD_SPI2_MISO_PIN 4 // PB14
|
|
#define BOARD_SPI2_MOSI_PIN 5 // PB15
|
|
#define BOARD_SPI3_MOSI_PIN 18
|
|
#define BOARD_SPI3_MISO_PIN 17
|
|
#define BOARD_SPI3_SCK_PIN 16
|
|
|
|
|
|
|
|
#define BOARD_MPU6000_CS_PIN 51
|
|
#define BOARD_MPU6000_DRDY_PIN 10 // PC4
|
|
|
|
|
|
#define BOARD_USB_SENSE 11 // PC5
|
|
|
|
|
|
# define BOARD_BLUE_LED_PIN 36 // BLUE
|
|
# define BOARD_GREEN_LED_PIN 9 // frequency select - resistor to VCC or ground
|
|
|
|
# define HAL_GPIO_A_LED_PIN BOARD_BLUE_LED_PIN
|
|
# define HAL_GPIO_B_LED_PIN BOARD_GREEN_LED_PIN
|
|
|
|
# define HAL_LED_ON LOW
|
|
# define HAL_LED_OFF HIGH
|
|
|
|
|
|
#define BOARD_NR_GPIO_PINS 109
|
|
|
|
#define I2C1_SDA PB9
|
|
#define I2C1_SCL PB8
|
|
|
|
#define I2C2_SDA PB11
|
|
#define I2C2_SCL PB10
|
|
|
|
#define BOARD_I2C_BUS_INT 1 // hardware internal I2C
|
|
|
|
#define BOARD_I2C_BUS_EXT 2 // external soft I2C
|
|
#define BOARD_I2C_BUS_SLOW 2 // slow down this bus
|
|
|
|
// bus 2 (soft) pins
|
|
#define BOARD_SOFT_SCL 105
|
|
#define BOARD_SOFT_SDA 26
|
|
|
|
//#define BOARD_BARO_DEFAULT HAL_BARO_BMP085_I2C
|
|
//#define HAL_BARO_BMP085_BUS BOARD_I2C_BUS_EXT
|
|
|
|
#define BOARD_COMPASS_DEFAULT HAL_COMPASS_HMC5843
|
|
|
|
#define HAL_COMPASS_HMC5843_I2C_BUS BOARD_I2C_BUS_EXT
|
|
#define HAL_COMPASS_HMC5843_I2C_ADDR (0x1E)
|
|
#define HAL_COMPASS_HMC5843_ROTATION ROTATION_NONE
|
|
|
|
|
|
#define BOARD_INS_DEFAULT HAL_INS_MPU60XX_SPI
|
|
#define BOARD_INS_ROTATION ROTATION_YAW_180
|
|
#define BOARD_INS_MPU60x0_NAME "mpu6000"
|
|
|
|
|
|
#define BOARD_STORAGE_SIZE 8192 //4096 // EEPROM size
|
|
|
|
#define BOARD_DATAFLASH_NAME "dataflash"
|
|
#define BOARD_DATAFLASH_PAGES 0x2000 // in 256-bytes pages
|
|
#define BOARD_DATAFLASH_ERASE_SIZE (4096)// in bytes
|
|
|
|
#if 1// if board's dataflash supports 4k erases then we can use it as FAT and share it via USB
|
|
#define BOARD_DATAFLASH_FATFS
|
|
#define BOARD_HAS_SDIO
|
|
#define USB_MASSSTORAGE
|
|
#define HAL_BOARD_LOG_DIRECTORY "0:"
|
|
#define HAL_BOARD_TERRAIN_DIRECTORY "0:/TERRAIN"
|
|
//#define HAL_PARAM_DEFAULTS_PATH "0:/APM/defaults.parm"
|
|
#else
|
|
// old dataflash logs
|
|
#endif
|
|
|
|
#define BOARD_OSD_NAME "osd"
|
|
#define BOARD_OSD_CS_PIN 103
|
|
#define BOARD_OSD_VSYNC_PIN 9 // PC3, Frequency input (pin 11)
|
|
|
|
#define BOARD_OWN_NAME "MiniF4_OSD"
|
|
|
|
# define BOARD_PUSHBUTTON_PIN 254
|
|
# define BOARD_USB_MUX_PIN -1
|
|
# define BOARD_BATTERY_VOLT_PIN 8 // Battery voltage on A0 (PC2) D8
|
|
# define BOARD_BATTERY_CURR_PIN 7 // Battery current on A1 (PC1) D7
|
|
# define BOARD_SONAR_SOURCE_ANALOG_PIN 254
|
|
|
|
#define BOARD_USB_DMINUS 108
|
|
|
|
|
|
#define BOARD_SBUS_UART 1 // can use some UART as hardware inverted input
|
|
|
|
#define USE_SERIAL_4WAY_BLHELI_INTERFACE
|
|
|
|
// use soft I2C driver instead hardware
|
|
//#define BOARD_SOFT_I2C
|
|
|
|
// motor layouts
|
|
#define SERVO_PIN_1 46 // PB0
|
|
#define SERVO_PIN_2 45 // PB1
|
|
#define SERVO_PIN_3 50 // PA3
|
|
#define SERVO_PIN_4 49 // PA2
|
|
#define SERVO_PIN_5 48 // PA1
|
|
#define SERVO_PIN_6 22 // PA8
|
|
|
|
#define MOTOR_LAYOUT_DEFAULT 0
|
|
|
|
//#define HAL_CONSOLE uart1Driver // console on radio
|
|
#define HAL_CONSOLE USB_Driver // console on USB
|
|
#define HAL_CONSOLE_PORT 0 // console on USB
|
|
|
|
|
|
|
|
/*
|
|
|
|
// @Param: USB_STORAGE
|
|
// @DisplayName: allows access to SD card at next reboot
|
|
// @Description: Allows to read/write internal SD card via USB mass-storage protocol. Auto-reset.
|
|
// @Values: 0:normal, 1:work as USB flash drive
|
|
// @User: Advanced
|
|
AP_GROUPINFO("USB_STORAGE", 8, AP_Param_Helper, _usb_storage, 0), \
|
|
|
|
*/
|
|
#define BOARD_HAL_VARINFO \
|
|
AP_GROUPINFO("USB_STORAGE", 30, AP_Param_Helper, _usb_storage, 0),
|
|
|
|
|
|
// parameters
|
|
#define BOARD_HAL_PARAMS \
|
|
AP_Int8 _usb_storage;
|
|
|
|
#define USB_MASSSTORAGE
|
|
|
|
#endif
|