When building for px4-v2 we have an warning because we are checking for
the value of this undefined macro. Just change both checks to use
"defined()".
../../libraries/AP_HAL_PX4/Util.cpp:115:7: warning: "CONFIG_ARCH_BOARD_PX4FMU_V4" is not defined [-Wundef]
#elif CONFIG_ARCH_BOARD_PX4FMU_V4
^
when this is set the board RGB LED will be controlled by MAVLink
instead of internally. This is useful for cases where the LED patterns
and colours needed are specified by an external authority (such as the
OBC organisers)
When switching over to a back up magnetometer, ensure that the earth field estimate are reset. other wise mag earth field estimates due to the previous failed mag could cause data from the new mag to be rejected.
This bug created a race condition whereby if the EKF had to reset the yaw to the GPS ground course to recover from a bad magnetometer, the new heading could be over-written by the bad magnetic heading when the plane reached the height for the scheduled reset.
If the GPS receiver was disconnected and no data received, then then the gpsGoodToAlign check did not get a chance to run and becasue it was previously true the EKF would switch back into aiding.
This prevents this by ensuring that gpsGoodToAlign defaults to false when the check is not being performed.
An additional check has also been dded to ensure that there is GPS data to fuse before we declare ready to use GPS.
Switching in and out of aiding modes was being performed in more than one place and was using two variables.
The reversion out of GPS mode due to prolonged loss of GPS was not working.
This consolidates the logic and ensures that PV_AidingMode is only changed by the setAidingMode function.
The filter status logic calculations were being repeated every time the get function was called.
The logic is now updated once per filter update step and a separate get function added
Split publishing of local position into horiz and vert components with separate validity checks
Split status reporting into separate update and get functions and only update once after each loop update. This removes unnecessary re-calculation of the status logic and ensures all consumers get the same data (avoid possible race conditions).
If we start GPS aiding before the gyro bias variances have reduced, glitches on the GPS can cause attitude disturbances that degrade flight accuracy during early flight.
The minimum version for gcc was supposed to be 4.9 for any platform.
However our build instructions are outdated. Remove the problematic
parts that use the sparse-endian.h header while we don't fix the setup
for windows.
When building for px4-v2 we have an warning because we are checking for
the value of this undefined macro. Just change both checks to use
"defined()".
../../libraries/AP_BoardConfig/AP_BoardConfig.cpp:36:7: warning: "CONFIG_ARCH_BOARD_PX4FMU_V4" is not defined [-Wundef]
#elif CONFIG_ARCH_BOARD_PX4FMU_V4
^
during the first part of a takeoff when we have not yet reached the
target airspeed this forces the throttle to maximum. This fixes a case
where the throttle may drop too low during the first part of takeoff
and lead to a stall.
The reason of defining BMI160_MAX_FIFO_SAMPLES as 8 can be found on the
following histogram of the number of samples in the FIFO on each read while
performing the accelerometer calibration process:
Samples Count Freq Acc. Freq
------------------------------
1 3842 0.1201 0.120111
2 13172 0.4118 0.531904
3 9065 0.2834 0.815300
4 2710 0.0847 0.900022
5 2231 0.0697 0.969769
6 816 0.0255 0.995279
7 137 0.0043 0.999562
8 13 0.0004 0.999969
13 1 0.0000 1.000000
Using factory method maked it easier to grasp the lifetime of all object
that get created and destroyed. Instead of spanning this thoughout whole
source file we have it nicely encapsulated in this a little horrendeous
_parseDevicePath that is of course to improve more.
Otherwise we're going to leak memory without any need.
Before this fix we've created ConsoleDevice 4 times in case -A switch hadn't been supplied,
but we hadn't ever deleted those. Now there's no memory leak here.
Minor changes to follow coding style and improve readability:
- sort headers
- move struct definition to compilation unit rather than header
- Add braces to if, for, etc
- Initialize device on hw_init() method, allowing it not to be
present
- Add missing lock
- Add packed attribute to structs
- Move defines to source file
- Add missing semaphore take on bus
- Initialize device on init function rather than constructor: the
constructor may run before I2CDeviceManager is initialized since our
AP_Notify objects are static so it can't be used.
In _start_conversion(), the check for return code of _dev->transfer() was
inverted. The structure also needs to be PACKED, otherwise there will be
a hole in the middle. Fix these issues and use be16_t where it makes
sense.
In read() we need to check for the second byte of config register, so
either make it an array of uint8_t or convert from big endian to host
endianness. It's simpler to leave it as it was, accessing just the
first byte. Also the conversion value is in be16 type an needs to be
converted to host endiannes, not the opposite.
Fix bus number: all boards that use it expect it to be on bus 1, not 0.
