GCS_MAVLink: regenerate headers

libraries/GCS_MAVLink/include/mavlink/v1.0/ardupilotmega/ardupilotmega.h

@@ -51,6 +51,7 @@ typedef enum MAV_CMD
 	MAV_CMD_NAV_ROI=80, /* Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of intereset mode. (see MAV_ROI enum)| MISSION index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|  */
 	MAV_CMD_NAV_PATHPLANNING=81, /* Control autonomous path planning on the MAV. |0: Disable local obstacle avoidance / local path planning (without resetting map), 1: Enable local path planning, 2: Enable and reset local path planning| 0: Disable full path planning (without resetting map), 1: Enable, 2: Enable and reset map/occupancy grid, 3: Enable and reset planned route, but not occupancy grid| Empty| Yaw angle at goal, in compass degrees, [0..360]| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal|  */
 	MAV_CMD_NAV_SPLINE_WAYPOINT=82, /* Navigate to MISSION using a spline path. |Hold time in decimal seconds. (ignored by fixed wing, time to stay at MISSION for rotary wing)| Empty| Empty| Empty| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal|  */
+	MAV_CMD_NAV_ALTITUDE_WAIT=83, /* Mission command to wait for an altitude or downwards vertical speed. This is meant for high altitude balloon launches, allowing the aircraft to be idle until either an altitude is reached or a negative vertical speed is reached (indicating early balloon burst). The wiggle time is how often to wiggle the control surfaces to prevent them seizing up. |altitude (m)| descent speed (m/s)| Wiggle Time (s)| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_NAV_GUIDED_ENABLE=92, /* hand control over to an external controller |On / Off (> 0.5f on)| Empty| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_NAV_LAST=95, /* NOP - This command is only used to mark the upper limit of the NAV/ACTION commands in the enumeration |Empty| Empty| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_CONDITION_DELAY=112, /* Delay mission state machine. |Delay in seconds (decimal)| Empty| Empty| Empty| Empty| Empty| Empty|  */
@@ -83,6 +84,7 @@ typedef enum MAV_CMD
 	MAV_CMD_DO_MOTOR_TEST=209, /* Mission command to perform motor test |motor sequence number (a number from 1 to max number of motors on the vehicle)| throttle type (0=throttle percentage, 1=PWM, 2=pilot throttle channel pass-through. See MOTOR_TEST_THROTTLE_TYPE enum)| throttle| timeout (in seconds)| Empty| Empty| Empty|  */
 	MAV_CMD_DO_INVERTED_FLIGHT=210, /* Change to/from inverted flight |inverted (0=normal, 1=inverted)| Empty| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_GRIPPER=211, /* Mission command to operate EPM gripper |gripper number (a number from 1 to max number of grippers on the vehicle)| gripper action (0=release, 1=grab. See GRIPPER_ACTIONS enum)| Empty| Empty| Empty| Empty| Empty|  */
+	MAV_CMD_DO_AUTOTUNE_ENABLE=212, /* Enable/disable autotune |enable (1: enable, 0:disable)| Empty| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_MOUNT_CONTROL_QUAT=220, /* Mission command to control a camera or antenna mount, using a quaternion as reference. |q1 - quaternion param #1, w (1 in null-rotation)| q2 - quaternion param #2, x (0 in null-rotation)| q3 - quaternion param #3, y (0 in null-rotation)| q4 - quaternion param #4, z (0 in null-rotation)| Empty| Empty| Empty|  */
 	MAV_CMD_DO_GUIDED_MASTER=221, /* set id of master controller |System ID| Component ID| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_GUIDED_LIMITS=222, /* set limits for external control |timeout - maximum time (in seconds) that external controller will be allowed to control vehicle. 0 means no timeout| absolute altitude min (in meters, AMSL) - if vehicle moves below this alt, the command will be aborted and the mission will continue.  0 means no lower altitude limit| absolute altitude max (in meters)- if vehicle moves above this alt, the command will be aborted and the mission will continue.  0 means no upper altitude limit| horizontal move limit (in meters, AMSL) - if vehicle moves more than this distance from it's location at the moment the command was executed, the command will be aborted and the mission will continue. 0 means no horizontal altitude limit| Empty| Empty| Empty|  */

libraries/GCS_MAVLink/include/mavlink/v1.0/ardupilotmega/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Jun 12 04:32:09 2015"
+#define MAVLINK_BUILD_DATE "Mon Jun 15 09:19:41 2015"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

libraries/GCS_MAVLink/include/mavlink/v1.0/common/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Jun 12 04:32:12 2015"
+#define MAVLINK_BUILD_DATE "Mon Jun 15 09:19:44 2015"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255