mirror of https://github.com/ArduPilot/ardupilot
201 lines
4.4 KiB
Plaintext
201 lines
4.4 KiB
Plaintext
# hw definition file for processing by chibios_pins.py
|
|
# for SkystarsH7HD
|
|
|
|
# MCU class and specific type
|
|
MCU STM32H7xx STM32H743xx
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 1075
|
|
|
|
# crystal frequency, setup to use external oscillator
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
FLASH_SIZE_KB 2048
|
|
|
|
env OPTIMIZE -O2
|
|
|
|
# ChibiOS system timer
|
|
STM32_ST_USE_TIMER 12
|
|
define CH_CFG_ST_RESOLUTION 16
|
|
|
|
# leave 1 sectors free
|
|
FLASH_RESERVE_START_KB 128
|
|
|
|
# use last 2 pages for flash storage
|
|
# H743 has 16 pages of 128k each
|
|
STORAGE_FLASH_PAGE 14
|
|
define HAL_STORAGE_SIZE 32768
|
|
|
|
# enable logging to dataflash
|
|
define HAL_LOGGING_DATAFLASH_ENABLED 1
|
|
|
|
# order of UARTs (and USB)
|
|
SERIAL_ORDER OTG1 USART1 USART2 USART3 UART4 UART5 USART6 UART7 UART8
|
|
|
|
# buzzer
|
|
PB3 BUZZER OUTPUT LOW PULLDOWN GPIO(80)
|
|
define HAL_BUZZER_PIN 80
|
|
define AP_NOTIFY_TONEALARM_ENABLED 1
|
|
|
|
# USB
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# SPI1 for BMI270 (Gyro 1)
|
|
PC15 BMI270_CS1 CS
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PD7 SPI1_MOSI SPI1
|
|
PB2 BMI270_INT1 INPUT
|
|
|
|
# SPI2 for AT7456E OSD
|
|
PB12 AT7456E_CS CS
|
|
PB13 SPI2_SCK SPI2
|
|
PB14 SPI2_MISO SPI2
|
|
PB15 SPI2_MOSI SPI2
|
|
|
|
# SPI3 for W25Q128 dataflash
|
|
PA15 FLASH_CS CS
|
|
PC10 SPI3_SCK SPI3
|
|
PC11 SPI3_MISO SPI3
|
|
PC12 SPI3_MOSI SPI3
|
|
|
|
# SPI4 for BMI270 (Gyro 2)
|
|
PE11 BMI270_CS2 CS
|
|
PE12 SPI4_SCK SPI4
|
|
PE13 SPI4_MISO SPI4
|
|
PE14 SPI4_MOSI SPI4
|
|
PE15 BMI270_INT2 INPUT
|
|
|
|
DMA_PRIORITY TIM1* TIM4* TIM3* TIM2* SPI1* SPI4*
|
|
DMA_NOSHARE SPI1_RX SPI2_TX SPI4_RX USART6_RX
|
|
|
|
# spi devices
|
|
SPIDEV bmi270_1 SPI1 DEVID1 BMI270_CS1 MODE3 1*MHZ 10*MHZ
|
|
SPIDEV osd SPI2 DEVID2 AT7456E_CS MODE0 10*MHZ 10*MHZ
|
|
SPIDEV dataflash SPI3 DEVID3 FLASH_CS MODE3 32*MHZ 32*MHZ
|
|
SPIDEV bmi270_2 SPI4 DEVID4 BMI270_CS2 MODE3 1*MHZ 10*MHZ
|
|
|
|
# one I2C bus
|
|
I2C_ORDER I2C2 I2C1
|
|
|
|
# I2C1 - external
|
|
PB8 I2C1_SCL I2C1
|
|
PB9 I2C1_SDA I2C1
|
|
|
|
# I2C2 - internal Baro
|
|
PB10 I2C2_SCL I2C2
|
|
PB11 I2C2_SDA I2C2
|
|
|
|
PC0 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
PC1 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
# VTX Power control - should be high at startup to ensure power
|
|
PC5 VTX_PWR OUTPUT HIGH GPIO(81) # labelled as "Pit-1"
|
|
# Camera selection - should be high so that Video 1 is selected by default
|
|
PC2 VID_SELECT OUTPUT HIGH GPIO(82) # labelled as "PIN-EN"
|
|
# OSD pad for TTL based OSD control, not supported by AP
|
|
PD2 CAM_C OUTPUT LOW GPIO(83) # labelled as "CAM-C"
|
|
|
|
|
|
# define default battery setup
|
|
define HAL_BATT_MONITOR_DEFAULT 4
|
|
define HAL_BATT_VOLT_PIN 10
|
|
define HAL_BATT_CURR_PIN 11
|
|
define HAL_BATT2_VOLT_PIN 10
|
|
define HAL_BATT2_CURR_PIN 12
|
|
define HAL_BATT_VOLT_SCALE 11.1
|
|
define HAL_BATT_CURR_SCALE 59.5
|
|
define HAL_BATT2_VOLT_SCALE 11.1
|
|
define HAL_BATT2_CURR_SCALE 59.5
|
|
|
|
PC3 RSSI_ADC ADC1
|
|
define BOARD_RSSI_ANA_PIN 13
|
|
|
|
PE3 LED0 OUTPUT LOW GPIO(90) # red, labelled as LED1
|
|
PE4 LED1 OUTPUT LOW GPIO(91) # blue, labelled as LED2
|
|
define HAL_GPIO_A_LED_PIN 90
|
|
define HAL_GPIO_B_LED_PIN 91
|
|
define HAL_GPIO_LED_OFF 1
|
|
|
|
# USART1
|
|
PA9 USART1_TX USART1
|
|
PA10 USART1_RX USART1
|
|
|
|
# USART2
|
|
PD5 USART2_TX USART2
|
|
PD6 USART2_RX USART2
|
|
|
|
# USART3
|
|
PD8 USART3_TX USART3
|
|
PD9 USART3_RX USART3
|
|
|
|
# UART4
|
|
PD0 UART4_RX UART4
|
|
PD1 UART4_TX UART4
|
|
|
|
# UART5
|
|
PB5 UART5_RX UART5
|
|
PB6 UART5_TX UART5
|
|
|
|
# USART6 (RX / SBUS)
|
|
# as an alternative config setup the RX6 pin as a uart. This allows
|
|
# for bi-directional UART based receiver protocols such as FPort
|
|
# without any extra hardware
|
|
PC6 USART6_TX USART6 NODMA
|
|
PC7 USART6_RX USART6 NODMA ALT(1)
|
|
|
|
# UART7
|
|
PE7 UART7_RX UART7
|
|
PE8 UART7_TX UART7
|
|
|
|
# UART8
|
|
PE0 UART8_RX UART8
|
|
PE1 UART8_TX UART8
|
|
|
|
define DEFAULT_SERIAL6_PROTOCOL SerialProtocol_RCIN
|
|
define DEFAULT_SERIAL6_BAUD 115
|
|
|
|
# Motors
|
|
PB0 TIM1_CH2N TIM1 PWM(1) GPIO(50)
|
|
PB1 TIM1_CH3N TIM1 PWM(2) GPIO(51)
|
|
PD12 TIM4_CH1 TIM4 PWM(3) GPIO(52)
|
|
PD13 TIM4_CH2 TIM4 PWM(4) GPIO(53)
|
|
PA0 TIM2_CH1 TIM2 PWM(5) GPIO(54)
|
|
PA1 TIM2_CH2 TIM2 PWM(6) GPIO(55)
|
|
PA2 TIM2_CH3 TIM2 PWM(7) GPIO(56)
|
|
PA3 TIM2_CH4 TIM2 PWM(8) GPIO(57)
|
|
|
|
# LED strip WS2812 / Neopixel
|
|
PA8 TIM1_CH1 TIM1 PWM(9) GPIO(58)
|
|
|
|
# RC input defaults to timer capture
|
|
PC7 TIM3_CH2 TIM3 RCININT PULLDOWN LOW
|
|
|
|
# no built-in compass, but probe the i2c bus for all possible
|
|
# external compass types
|
|
define ALLOW_ARM_NO_COMPASS
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
|
|
# two IMU
|
|
IMU BMI270 SPI:bmi270_1 ROTATION_ROLL_180_YAW_90
|
|
IMU BMI270 SPI:bmi270_2 ROTATION_ROLL_180
|
|
|
|
# one BARO
|
|
BARO BMP280 I2C:0:0x76
|
|
|
|
# setup for OSD
|
|
define OSD_ENABLED 1
|
|
define HAL_OSD_TYPE_DEFAULT 1
|
|
ROMFS_WILDCARD libraries/AP_OSD/fonts/font*.bin
|
|
|
|
define STM32_PWM_USE_ADVANCED TRUE
|
|
|
|
define DEFAULT_NTF_LED_TYPES 257
|
|
|
|
define AP_SCRIPTING_ENABLED 0
|