ardupilot/ArduCopter/mode_acro.cpp

#include "Copter.h"

#include "mode.h"

#if MODE_ACRO_ENABLED == ENABLED

/*
 * Init and run calls for acro flight mode
 */

void ModeAcro::run()
{
    // convert the input to the desired body frame rate
    float target_roll, target_pitch, target_yaw;
    get_pilot_desired_angle_rates(channel_roll->get_control_in(), channel_pitch->get_control_in(), channel_yaw->get_control_in(), target_roll, target_pitch, target_yaw);

    if (!motors->armed()) {
        // Motors should be Stopped
        motors->set_desired_spool_state(AP_Motors::DesiredSpoolState::SHUT_DOWN);
    } else if (copter.ap.throttle_zero) {
        // Attempting to Land
        motors->set_desired_spool_state(AP_Motors::DesiredSpoolState::GROUND_IDLE);
    } else {
        motors->set_desired_spool_state(AP_Motors::DesiredSpoolState::THROTTLE_UNLIMITED);
    }

    switch (motors->get_spool_state()) {
    case AP_Motors::SpoolState::SHUT_DOWN:
        // Motors Stopped
        attitude_control->reset_target_and_rate(true);
        attitude_control->reset_rate_controller_I_terms();
        break;

    case AP_Motors::SpoolState::GROUND_IDLE:
        // Landed
        attitude_control->reset_target_and_rate();
        attitude_control->reset_rate_controller_I_terms_smoothly();
        break;

    case AP_Motors::SpoolState::THROTTLE_UNLIMITED:
        // clear landing flag above zero throttle
        if (!motors->limit.throttle_lower) {
            set_land_complete(false);
        }
        break;

    case AP_Motors::SpoolState::SPOOLING_UP:
    case AP_Motors::SpoolState::SPOOLING_DOWN:
        // do nothing
        break;
    }

    // run attitude controller
    if (g2.acro_options.get() & uint8_t(AcroOptions::RATE_LOOP_ONLY)) {
        attitude_control->input_rate_bf_roll_pitch_yaw_2(target_roll, target_pitch, target_yaw);
    } else {
        attitude_control->input_rate_bf_roll_pitch_yaw(target_roll, target_pitch, target_yaw);
    }

    // output pilot's throttle without angle boost
    attitude_control->set_throttle_out(get_pilot_desired_throttle(),
                                       false,
                                       copter.g.throttle_filt);
}

bool ModeAcro::init(bool ignore_checks)
{
    if (g2.acro_options.get() & uint8_t(AcroOptions::AIR_MODE)) {
        disable_air_mode_reset = false;
        copter.air_mode = AirMode::AIRMODE_ENABLED;
    }

    return true;
}

void ModeAcro::exit()
{
    if (!disable_air_mode_reset && (g2.acro_options.get() & uint8_t(AcroOptions::AIR_MODE))) {
        copter.air_mode = AirMode::AIRMODE_DISABLED;
    }
    disable_air_mode_reset = false;
}

void ModeAcro::air_mode_aux_changed()
{
    disable_air_mode_reset = true;
}

float ModeAcro::throttle_hover() const
{
    if (g2.acro_thr_mid > 0) {
        return g2.acro_thr_mid;
    }
    return Mode::throttle_hover();
}

// get_pilot_desired_angle_rates - transform pilot's roll pitch and yaw input into a desired lean angle rates
// returns desired angle rates in centi-degrees-per-second
void ModeAcro::get_pilot_desired_angle_rates(int16_t roll_in, int16_t pitch_in, int16_t yaw_in, float &roll_out, float &pitch_out, float &yaw_out)
{
    float rate_limit;
    Vector3f rate_ef_level, rate_bf_level, rate_bf_request;

    // apply circular limit to pitch and roll inputs
    float total_in = norm(pitch_in, roll_in);

    if (total_in > ROLL_PITCH_YAW_INPUT_MAX) {
        float ratio = (float)ROLL_PITCH_YAW_INPUT_MAX / total_in;
        roll_in *= ratio;
        pitch_in *= ratio;
    }

    // range check expo
    g.acro_rp_expo = constrain_float(g.acro_rp_expo, -0.5f, 1.0f);
    
    // calculate roll, pitch rate requests
    if (is_zero(g.acro_rp_expo)) {
        rate_bf_request.x = roll_in * g.acro_rp_p;
        rate_bf_request.y = pitch_in * g.acro_rp_p;
    } else {
        // expo variables
        float rp_in, rp_in3, rp_out;

        // roll expo
        rp_in = float(roll_in)/ROLL_PITCH_YAW_INPUT_MAX;
        rp_in3 = rp_in*rp_in*rp_in;
        rp_out = (g.acro_rp_expo * rp_in3) + ((1.0f - g.acro_rp_expo) * rp_in);
        rate_bf_request.x = ROLL_PITCH_YAW_INPUT_MAX * rp_out * g.acro_rp_p;

        // pitch expo
        rp_in = float(pitch_in)/ROLL_PITCH_YAW_INPUT_MAX;
        rp_in3 = rp_in*rp_in*rp_in;
        rp_out = (g.acro_rp_expo * rp_in3) + ((1.0f - g.acro_rp_expo) * rp_in);
        rate_bf_request.y = ROLL_PITCH_YAW_INPUT_MAX * rp_out * g.acro_rp_p;
    }

    // calculate yaw rate request
    rate_bf_request.z = get_pilot_desired_yaw_rate(yaw_in);

    // calculate earth frame rate corrections to pull the copter back to level while in ACRO mode

    if (g.acro_trainer != (uint8_t)Trainer::OFF) {

        // get attitude targets
        const Vector3f att_target = attitude_control->get_att_target_euler_cd();

        // Calculate trainer mode earth frame rate command for roll
        int32_t roll_angle = wrap_180_cd(att_target.x);
        rate_ef_level.x = -constrain_int32(roll_angle, -ACRO_LEVEL_MAX_ANGLE, ACRO_LEVEL_MAX_ANGLE) * g.acro_balance_roll;

        // Calculate trainer mode earth frame rate command for pitch
        int32_t pitch_angle = wrap_180_cd(att_target.y);
        rate_ef_level.y = -constrain_int32(pitch_angle, -ACRO_LEVEL_MAX_ANGLE, ACRO_LEVEL_MAX_ANGLE) * g.acro_balance_pitch;

        // Calculate trainer mode earth frame rate command for yaw
        rate_ef_level.z = 0;

        // Calculate angle limiting earth frame rate commands
        if (g.acro_trainer == (uint8_t)Trainer::LIMITED) {
            const float angle_max = copter.aparm.angle_max;
            if (roll_angle > angle_max){
                rate_ef_level.x += sqrt_controller(angle_max - roll_angle, g.acro_rp_p * 4.5, attitude_control->get_accel_roll_max(), G_Dt);
            }else if (roll_angle < -angle_max) {
                rate_ef_level.x += sqrt_controller(-angle_max - roll_angle, g.acro_rp_p * 4.5, attitude_control->get_accel_roll_max(), G_Dt);
            }

            if (pitch_angle > angle_max){
                rate_ef_level.y += sqrt_controller(angle_max - pitch_angle, g.acro_rp_p * 4.5, attitude_control->get_accel_pitch_max(), G_Dt);
            }else if (pitch_angle < -angle_max) {
                rate_ef_level.y += sqrt_controller(-angle_max - pitch_angle, g.acro_rp_p * 4.5, attitude_control->get_accel_pitch_max(), G_Dt);
            }
        }

        // convert earth-frame level rates to body-frame level rates
        attitude_control->euler_rate_to_ang_vel(attitude_control->get_att_target_euler_cd()*radians(0.01f), rate_ef_level, rate_bf_level);

        // combine earth frame rate corrections with rate requests
        if (g.acro_trainer == (uint8_t)Trainer::LIMITED) {
            rate_bf_request.x += rate_bf_level.x;
            rate_bf_request.y += rate_bf_level.y;
            rate_bf_request.z += rate_bf_level.z;
        }else{
            float acro_level_mix = constrain_float(1-float(MAX(MAX(abs(roll_in), abs(pitch_in)), abs(yaw_in))/4500.0), 0, 1)*ahrs.cos_pitch();

            // Scale leveling rates by stick input
            rate_bf_level = rate_bf_level*acro_level_mix;

            // Calculate rate limit to prevent change of rate through inverted
            rate_limit = fabsf(fabsf(rate_bf_request.x)-fabsf(rate_bf_level.x));
            rate_bf_request.x += rate_bf_level.x;
            rate_bf_request.x = constrain_float(rate_bf_request.x, -rate_limit, rate_limit);

            // Calculate rate limit to prevent change of rate through inverted
            rate_limit = fabsf(fabsf(rate_bf_request.y)-fabsf(rate_bf_level.y));
            rate_bf_request.y += rate_bf_level.y;
            rate_bf_request.y = constrain_float(rate_bf_request.y, -rate_limit, rate_limit);

            // Calculate rate limit to prevent change of rate through inverted
            rate_limit = fabsf(fabsf(rate_bf_request.z)-fabsf(rate_bf_level.z));
            rate_bf_request.z += rate_bf_level.z;
            rate_bf_request.z = constrain_float(rate_bf_request.z, -rate_limit, rate_limit);
        }
    }

    // hand back rate request
    roll_out = rate_bf_request.x;
    pitch_out = rate_bf_request.y;
    yaw_out = rate_bf_request.z;
}
#endif