ardupilot/libraries/AP_AHRS/AP_AHRS_MPU6000.cpp

326 lines
10 KiB
C++

/*
* AP_AHRS_MPU6000.cpp
*
* AHRS system using MPU6000's internal calculations
*
* Adapted for the general ArduPilot AHRS interface by Andrew Tridgell
*
* This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU Lesser General Public License
* as published by the Free Software Foundation; either version 2.1
* of the License, or (at your option) any later version.
*/
#include <AP_AHRS.h>
#include <AP_HAL.h>
extern const AP_HAL::HAL& hal;
// this is the speed in cm/s above which we first get a yaw lock with
// the GPS
#define GPS_SPEED_MIN 300
// this is the speed in cm/s at which we stop using drift correction
// from the GPS and wait for the ground speed to get above GPS_SPEED_MIN
#define GPS_SPEED_RESET 100
// the limit (in degrees/second) beyond which we stop integrating
// omega_I. At larger spin rates the DCM PI controller can get 'dizzy'
// which results in false gyro drift. See
// http://gentlenav.googlecode.com/files/fastRotations.pdf
#define SPIN_RATE_LIMIT 20
void
AP_AHRS_MPU6000::init()
{
// suspend timer so interrupts on spi bus do not interfere with
// communication to mpu6000
hal.scheduler->suspend_timer_procs();
_mpu6000->dmp_init();
push_gains_to_dmp();
_mpu6000->push_gyro_offsets_to_dmp();
// restart timer
hal.scheduler->resume_timer_procs();
};
// run a full MPU6000 update round
void
AP_AHRS_MPU6000::update(void)
{
float delta_t;
// tell the IMU to grab some data.
if( !_secondary_ahrs ) {
_ins->update();
}
// ask the IMU how much time this sensor reading represents
delta_t = _ins->get_delta_time();
// convert the quaternions into a DCM matrix
_mpu6000->quaternion.rotation_matrix(_dcm_matrix);
// we run the gyro bias correction using gravity vector algorithm
drift_correction(delta_t);
// Calculate pitch, roll, yaw for stabilization and navigation
euler_angles();
}
// wrap_PI - ensure an angle (expressed in radians) is between -PI and PI
// TO-DO: should remove and replace with more standard functions
float AP_AHRS_MPU6000::wrap_PI(float angle_in_radians)
{
if( angle_in_radians > M_PI ) {
return(angle_in_radians - 2*M_PI);
}
else if( angle_in_radians < -M_PI ) {
return(angle_in_radians + 2*M_PI);
}
else{
return(angle_in_radians);
}
}
// Function to correct the gyroX and gyroY bias (roll and pitch) using the
// gravity vector from accelerometers We use the internal chip axis definition
// to make the bias correction because both sensors outputs (gyros and accels)
// are in chip axis definition
void AP_AHRS_MPU6000::drift_correction( float deltat )
{
float errorRollPitch[2];
// Get current values for gyros
_accel_vector = _ins->get_accel();
// We take the accelerometer readings and cumulate to average them and
// obtain the gravity vector
_accel_filtered += _accel_vector;
_accel_filtered_samples++;
_gyro_bias_from_gravity_counter++;
// We make the bias calculation and correction at a lower rate
// (GYRO_BIAS_FROM_GRAVITY_RATE)
if( _gyro_bias_from_gravity_counter == GYRO_BIAS_FROM_GRAVITY_RATE ) {
_gyro_bias_from_gravity_counter = 0;
_accel_filtered /= _accel_filtered_samples; // average
// Adjust ground reference : Accel Cross Gravity to obtain the error
// between gravity from accels and gravity from attitude solution
// errorRollPitch are in Accel LSB units
errorRollPitch[0] = _accel_filtered.y * _dcm_matrix.c.z
+ _accel_filtered.z * _dcm_matrix.c.x;
errorRollPitch[1] = -_accel_filtered.z * _dcm_matrix.c.y
- _accel_filtered.x * _dcm_matrix.c.z;
errorRollPitch[0] *= deltat * 1000;
errorRollPitch[1] *= deltat * 1000;
// we limit to maximum gyro drift rate on each axis
// 0.65*0.04 / 0.005 = 5.2
float drift_limit = _mpu6000->get_gyro_drift_rate() * deltat
/ _gyro_bias_from_gravity_gain;
errorRollPitch[0] = constrain(errorRollPitch[0],
-drift_limit, drift_limit);
errorRollPitch[1] = constrain(errorRollPitch[1],
-drift_limit, drift_limit);
// We correct gyroX and gyroY bias using the error vector
_gyro_bias[0] += errorRollPitch[0]*_gyro_bias_from_gravity_gain;
_gyro_bias[1] += errorRollPitch[1]*_gyro_bias_from_gravity_gain;
// TO-DO: fix this. Currently it makes the roll and pitch drift more!
// If bias values are greater than 1 LSB we update the hardware offset
// registers
if( fabs(_gyro_bias[0])>1.0 ) {
//_mpu6000->set_gyro_offsets(-1*(int)_gyro_bias[0],0,0);
//_mpu6000->set_gyro_offsets(0,-1*(int)_gyro_bias[0],0);
//_gyro_bias[0] -= (int)_gyro_bias[0]; // we remove the part that
// we have already corrected on registers...
}
if (fabs(_gyro_bias[1])>1.0) {
//_mpu6000->set_gyro_offsets(-1*(int)_gyro_bias[1],0,0);
//_gyro_bias[1] -= (int)_gyro_bias[1];
}
// Reset the accelerometer variables
_accel_filtered.x = 0;
_accel_filtered.y = 0;
_accel_filtered.z = 0;
_accel_filtered_samples=0;
}
// correct the yaw
drift_correction_yaw();
}
/*
* reset the DCM matrix and omega. Used on ground start, and on
* extreme errors in the matrix
*/
void
AP_AHRS_MPU6000::reset(bool recover_eulers)
{
// if the caller wants us to try to recover to the current
// attitude then calculate the dcm matrix from the current
// roll/pitch/yaw values
if (recover_eulers && !isnan(roll) && !isnan(pitch) && !isnan(yaw)) {
_dcm_matrix.from_euler(roll, pitch, yaw);
} else {
// otherwise make it flat
_dcm_matrix.from_euler(0, 0, 0);
}
}
// push offsets down from IMU to INS (required so MPU6000 can perform it's own
// attitude estimation)
void
AP_AHRS_MPU6000::push_offsets_to_ins()
{
// push down gyro offsets (TO-DO: why are x and y offsets are reversed?!)
_mpu6000->push_gyro_offsets_to_dmp();
// push down accelerometer offsets
// (TO-DO: why are x and y offsets are reversed?!)
_mpu6000->push_accel_offsets_to_dmp();
}
void
AP_AHRS_MPU6000::push_gains_to_dmp()
{
uint8_t gain;
if( _kp.get() >= 1.0 ) {
gain = 0xFF;
}else if( _kp.get() <= 0.0 ) {
gain = 0x00;
}else{
gain = (uint8_t)((float)0xFF * _kp.get());
}
_mpu6000->dmp_set_sensor_fusion_accel_gain(gain);
}
// produce a yaw error value. The returned value is proportional
// to sin() of the current heading error in earth frame
float
AP_AHRS_MPU6000::yaw_error_compass(void)
{
Vector3f mag = Vector3f(_compass->mag_x, _compass->mag_y, _compass->mag_z);
// get the mag vector in the earth frame
Vector3f rb = _dcm_matrix * mag;
rb.normalize();
if (rb.is_inf()) {
// not a valid vector
return 0.0;
}
// get the earths magnetic field (only X and Y components needed)
Vector3f mag_earth = Vector3f(cos(_compass->get_declination()),
sin(_compass->get_declination()), 0);
// calculate the error term in earth frame
Vector3f error = rb % mag_earth;
return error.z;
}
//
// drift_correction_yaw - yaw drift correction using the compass
// we have no way to update the dmp with it's actual heading from our
// compass instead we use the yaw_corrected variable to hold what we think
// is the real heading we also record what the dmp said it's last heading
// was in the yaw_last_uncorrected variable so that on the next iteration we
// can add the change in yaw to our estimate
//
void
AP_AHRS_MPU6000::drift_correction_yaw(void)
{
static float yaw_corrected = HEADING_UNKNOWN;
static float last_dmp_yaw = HEADING_UNKNOWN;
// roll pitch and yaw values from dmp
float dmp_roll, dmp_pitch, dmp_yaw;
// change in yaw according to dmp
float yaw_delta;
// difference between heading and corrected yaw
float yaw_error;
static float heading;
// get uncorrected yaw values from dmp
_mpu6000->quaternion.to_euler(&dmp_roll, &dmp_pitch, &dmp_yaw);
// initialise headings on first iteration
if( yaw_corrected == HEADING_UNKNOWN ) {
yaw_corrected = dmp_yaw;
last_dmp_yaw = dmp_yaw;
}
// change in yaw according to dmp
yaw_delta = wrap_PI(dmp_yaw - last_dmp_yaw);
yaw_corrected = wrap_PI(yaw_corrected + yaw_delta);
last_dmp_yaw = dmp_yaw;
// rebuild dcm matrix
_dcm_matrix.from_euler(dmp_roll, dmp_pitch, yaw_corrected);
// if we have new compass data
if(_compass && _compass->use_for_yaw() ) {
if(_compass->last_update != _compass_last_update) {
_compass_last_update = _compass->last_update;
heading = _compass->calculate_heading(_dcm_matrix);
// if this is the first good compass reading then set yaw to this heading
if( !_have_initial_yaw ) {
_have_initial_yaw = true;
yaw_corrected = wrap_PI(heading);
}
// yaw correction based on compass
//yaw_error = yaw_error_compass();
yaw_error = wrap_PI(heading - yaw_corrected);
// shift the corrected yaw towards the compass heading a bit
yaw_corrected += wrap_PI(yaw_error * _kp_yaw.get() * 0.1);
// rebuild the dcm matrix yet again
_dcm_matrix.from_euler(dmp_roll, dmp_pitch, yaw_corrected);
}
}
}
// calculate the euler angles which will be used for high level
// navigation control
void
AP_AHRS_MPU6000::euler_angles(void)
{
_dcm_matrix.to_euler(&roll, &pitch, &yaw);
// cannot use this because the quaternion is not correct for yaw drift
//quaternion.to_euler(&roll, &pitch, &yaw);
roll_sensor = degrees(roll) * 100;
pitch_sensor = degrees(pitch) * 100;
yaw_sensor = degrees(yaw) * 100;
if (yaw_sensor < 0)
yaw_sensor += 36000;
}
/* reporting of DCM state for MAVLink */
// average error_roll_pitch since last call
float AP_AHRS_MPU6000::get_error_rp(void)
{
// not yet supported with DMP
return 0.0;
}
// average error_yaw since last call
float AP_AHRS_MPU6000::get_error_yaw(void)
{
// not yet supported with DMP
return 0.0;
}