Mirror/ardupilot
5
0
Fork 0
mirror of https://github.com/ArduPilot/ardupilot synced 2025-01-19 23:28:32 -04:00
Code Issues Packages Projects Releases Wiki Activity
f1ff27ed08
ardupilot/APMrover2/Parameters.pde
Andrew Tridgell f1ff27ed08 Rover: major restructuring 
this removes a lot of the old arduplane code, and renames a lot of
variables.

This will need a lot more testing and fixup before being usable
2013-02-08 09:21:22 +11:00

306 lines
12 KiB
Plaintext
Raw Blame History

/// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: t -*-
/*
ArduPlane parameter definitions
This firmware is free software; you can redistribute it and/or
modify it under the terms of the GNU Lesser General Public
License as published by the Free Software Foundation; either
version 2.1 of the License, or (at your option) any later version.
*/
#define GSCALAR(v, name, def) { g.v.vtype, name, Parameters::k_param_ ## v, &g.v, {def_value:def} }
#define GGROUP(v, name, class) { AP_PARAM_GROUP, name, Parameters::k_param_ ## v, &g.v, {group_info:class::var_info} }
#define GOBJECT(v, name, class) { AP_PARAM_GROUP, name, Parameters::k_param_ ## v, &v, {group_info:class::var_info} }
const AP_Param::Info var_info[] PROGMEM = {
GSCALAR(format_version, "FORMAT_VERSION", 1),
GSCALAR(software_type, "SYSID_SW_TYPE", Parameters::k_software_type),
GSCALAR(sysid_this_mav, "SYSID_THISMAV", MAV_SYSTEM_ID),
GSCALAR(sysid_my_gcs, "SYSID_MYGCS", 255),
// @Param: SERIAL0_BAUD
// @DisplayName: Telemetry Baud Rate
// @Description: The baud rate used on the first serial port
// @Values: 1:1200,2:2400,4:4800,9:9600,19:19200,38:38400,57:57600,111:111100,115:115200
// @User: Standard
GSCALAR(serial0_baud, "SERIAL0_BAUD", SERIAL0_BAUD/1000),
// @Param: SERIAL3_BAUD
// @DisplayName: Telemetry Baud Rate
// @Description: The baud rate used on the telemetry port
// @Values: 1:1200,2:2400,4:4800,9:9600,19:19200,38:38400,57:57600,111:111100,115:115200
// @User: Standard
GSCALAR(serial3_baud, "SERIAL3_BAUD", SERIAL3_BAUD/1000),
// @Param: TELEM_DELAY
// @DisplayName: Telemetry startup delay
// @Description: The amount of time (in seconds) to delay radio telemetry to prevent an Xbee bricking on power up
// @User: Standard
// @Units: seconds
// @Range: 0 10
// @Increment: 1
GSCALAR(telem_delay, "TELEM_DELAY", 0),
// @Param: MANUAL_LEVEL
// @DisplayName: Manual Level
// @Description: Setting this to Disabled(0) will enable autolevel on every boot. Setting it to Enabled(1) will do a calibration only when you tell it to. This defaults to enabled.
// @Values: 0:Disabled,1:Enabled
// @User: Advanced
GSCALAR(manual_level, "MANUAL_LEVEL", 1),
// @Param: XTRK_GAIN_SC
// @DisplayName: Crosstrack Gain
// @Description: This controls how hard the Rover tries to follow the lines between waypoints, as opposed to driving directly to the next waypoint. The value is the scale between distance off the line and angle to meet the line (in Degrees * 100)
// @Range: 0 2000
// @Increment: 1
// @User: Standard
GSCALAR(crosstrack_gain, "XTRK_GAIN_SC", XTRACK_GAIN_SCALED),
// @Param: XTRK_ANGLE_CD
// @DisplayName: Crosstrack Entry Angle
// @Description: Maximum angle used to correct for track following.
// @Units: centi-Degrees
// @Range: 0 9000
// @Increment: 1
// @User: Standard
GSCALAR(crosstrack_entry_angle, "XTRK_ANGLE_CD", XTRACK_ENTRY_ANGLE_CENTIDEGREE),
GSCALAR(command_total, "CMD_TOTAL", 0),
GSCALAR(command_index, "CMD_INDEX", 0),
// @Param: WP_RADIUS
// @DisplayName: Waypoint radius
// @Description: The distance in meters from a waypoint when we consider the waypoint has been reached. This determines when the rover will turn along the next waypoint path.
// @Units: meters
// @Range: 0 1000
// @Increment: 0.1
// @User: Standard
GSCALAR(waypoint_radius, "WP_RADIUS", 2.0f),
// @Param: THR_MIN
// @DisplayName: Minimum Throttle
// @Description: The minimum throttle setting to which the autopilot will apply. This is mostly useful for rovers with internal combustion motors, to prevent the motor from cutting out in auto mode.
// @Units: Percent
// @Range: 0 100
// @Increment: 1
// @User: Standard
GSCALAR(throttle_min, "THR_MIN", THROTTLE_MIN),
// @Param: THR_MAX
// @DisplayName: Maximum Throttle
// @Description: The maximum throttle setting to which the autopilot will apply.
// @Units: Percent
// @Range: 0 100
// @Increment: 1
// @User: Standard
GSCALAR(throttle_max, "THR_MAX", THROTTLE_MAX),
// @Param: THR_SLEWRATE
// @DisplayName: Throttle slew rate
// @Description: maximum percentage change in throttle per second. A setting of 10 means to not change the throttle by more than 10% of the full throttle range in one second
// @Units: Percent
// @Range: 0 100
// @Increment: 1
// @User: Standard
GSCALAR(throttle_slewrate, "THR_SLEWRATE", 0),
// @Param: THR_FAILSAFE
// @DisplayName: Throttle Failsafe Enable
// @Description: The throttle failsafe allows you to configure a software failsafe activated by a setting on the throttle input channel to a low value. This can be used to detect the RC transmitter going out of range.
// @Values: 0:Disabled,1:Enabled
// @User: Standard
GSCALAR(throttle_fs_enabled, "THR_FAILSAFE", THROTTLE_FAILSAFE),
// @Param: THR_FS_VALUE
// @DisplayName: Throttle Failsafe Value
// @Description: The PWM level on channel 3 below which throttle sailsafe triggers.
// @User: Standard
GSCALAR(throttle_fs_value, "THR_FS_VALUE", THROTTLE_FS_VALUE),
// @Param: CRUISE_THROTTLE
// @DisplayName: Throttle cruise percentage
// @Description: The target percentage of throttle to apply for auto missions.
// @Units: Percent
// @Range: 0 100
// @Increment: 1
// @User: Standard
GSCALAR(throttle_cruise, "CRUISE_THROTTLE", 50),
// @Param: CRUISE_SPEED
// @DisplayName: Target speed in auto modes
// @Description: The target speed in auto missions.
// @Units: m/s
// @Range: 0 100
// @Increment: 0.1
// @User: Standard
GSCALAR(speed_cruise, "CRUISE_SPEED", 5),
// @Param: FS_GCS_ENABLE
// @DisplayName: GCS failsafe enable
// @Description: Enable ground control station telemetry failsafe
// @Values: 0:Disabled,1:Enabled
// @User: Standard
GSCALAR(gcs_heartbeat_fs_enabled, "FS_GCS_ENABLE", 0),
// @Param: MODE_CH
// @DisplayName: Mode channel
// @Description: RC Channel to use for flight mode control
// @User: Advanced
GSCALAR(mode_channel, "MODE_CH", MODE_CHANNEL),
// @Param: MODE1
// @DisplayName: Mode1
// @Values: 0:Manual,2:LEARNING,10:Auto,11:RTL,15:Guided
// @User: Standard
// @Description: Flight mode for switch position 1 (910 to 1230 and above 2049)
GSCALAR(mode1, "MODE1", MODE_1),
// @Param: MODE2
// @DisplayName: Mode2
// @Description: Flight mode for switch position 2 (1231 to 1360)
// @Values: 0:Manual,2:LEARNING,10:Auto,11:RTL,15:Guided
// @User: Standard
GSCALAR(mode2, "MODE2", MODE_2),
// @Param: MODE3
// @DisplayName: Mode3
// @Description: Flight mode for switch position 3 (1361 to 1490)
// @Values: 0:Manual,2:LEARNING,10:Auto,11:RTL,15:Guided
// @User: Standard
GSCALAR(mode3, "MODE3", MODE_3),
// @Param: MODE4
// @DisplayName: Mode4
// @Description: Flight mode for switch position 4 (1491 to 1620)
// @Values: 0:Manual,2:LEARNING,10:Auto,11:RTL,15:Guided
// @User: Standard
GSCALAR(mode4, "MODE4", MODE_4),
// @Param: MODE5
// @DisplayName: Mode5
// @Description: Flight mode for switch position 5 (1621 to 1749)
// @Values: 0:Manual,2:LEARNING,10:Auto,11:RTL,15:Guided
// @User: Standard
GSCALAR(mode5, "MODE5", MODE_5),
// @Param: MODE6
// @DisplayName: Mode6
// @Description: Flight mode for switch position 6 (1750 to 2049)
// @Values: 0:Manual,2:LEARNING,10:Auto,11:RTL,15:Guided
// @User: Standard
GSCALAR(mode6, "MODE6", MODE_6),
GSCALAR(num_resets, "SYS_NUM_RESETS", 0),
GSCALAR(log_bitmask, "LOG_BITMASK", DEFAULT_LOG_BITMASK),
GSCALAR(log_last_filenumber, "LOG_LASTFILE", 0),
GSCALAR(reset_switch_chan, "RST_SWITCH_CH", 0),
GSCALAR(ch7_option, "CH7_OPT", CH7_OPTION),
GSCALAR(compass_enabled, "MAG_ENABLE", MAGNETOMETER),
GSCALAR(battery_monitoring, "BATT_MONITOR", DISABLED),
GSCALAR(volt_div_ratio, "VOLT_DIVIDER", VOLT_DIV_RATIO),
GSCALAR(curr_amp_per_volt, "AMP_PER_VOLT", CURR_AMP_PER_VOLT),
GSCALAR(input_voltage, "INPUT_VOLTS", INPUT_VOLTAGE),
GSCALAR(pack_capacity, "BATT_CAPACITY", HIGH_DISCHARGE),
// @Param: BATT_VOLT_PIN
// @DisplayName: Battery Voltage sensing pin
// @Description: Setting this to 0 ~ 13 will enable battery current sensing on pins A0 ~ A13.
// @Values: -1:Disabled, 0:A0, 1:A1, 13:A13
// @User: Standard
GSCALAR(battery_volt_pin, "BATT_VOLT_PIN", 1),
// @Param: BATT_CURR_PIN
// @DisplayName: Battery Current sensing pin
// @Description: Setting this to 0 ~ 13 will enable battery current sensing on pins A0 ~ A13.
// @Values: -1:Disabled, 1:A1, 2:A2, 12:A12
// @User: Standard
GSCALAR(battery_curr_pin, "BATT_CURR_PIN", 2),
// @Param: RSSI_PIN
// @DisplayName: Receiver RSSI sensing pin
// @Description: This selects an analog pin for the receiver RSSI voltage. It assumes the voltage is 5V for max rssi, 0V for minimum
// @Values: -1:Disabled, 0:A0, 1:A1, 13:A13
// @User: Standard
GSCALAR(rssi_pin, "RSSI_PIN", -1),
#if HIL_MODE != HIL_MODE_ATTITUDE
#if CONFIG_SONAR == ENABLED
// @Param: SONAR_ENABLE
// @DisplayName: Enable Sonar
// @Description: Setting this to Enabled(1) will enable the sonar. Setting this to Disabled(0) will disable the sonar
// @Values: 0:Disabled,1:Enabled
// @User: Standard
GSCALAR(sonar_enabled, "SONAR_ENABLE", SONAR_ENABLED),
GSCALAR(sonar_type, "SONAR_TYPE", AP_RANGEFINDER_MAXSONARXL),
#endif
#endif
// ************************************************************
// APMrover parameters - JLN update
GSCALAR(sonar_trigger, "ROV_SONAR_TRIG", SONAR_TRIGGER),
GSCALAR(booster, "ROV_BOOSTER", BOOSTER),
// ************************************************************
GGROUP(channel_steer, "RC1_", RC_Channel),
GGROUP(rc_2, "RC2_", RC_Channel_aux),
GGROUP(channel_throttle, "RC3_", RC_Channel),
GGROUP(rc_4, "RC4_", RC_Channel_aux),
GGROUP(rc_5, "RC5_", RC_Channel_aux),
GGROUP(rc_6, "RC6_", RC_Channel_aux),
GGROUP(rc_7, "RC7_", RC_Channel_aux),
GGROUP(rc_8, "RC8_", RC_Channel_aux),
GGROUP(pidNavSteer, "HDNG2STEER_", PID),
GGROUP(pidServoSteer, "STEER2SRV_", PID),
GGROUP(pidSpeedThrottle, "SPEED2THR_", PID),
// variables not in the g class which contain EEPROM saved variables
GOBJECT(compass, "COMPASS_", Compass),
GOBJECT(gcs0, "SR0_", GCS_MAVLINK),
GOBJECT(gcs3, "SR3_", GCS_MAVLINK),
#if HIL_MODE == HIL_MODE_DISABLED
// @Group: INS_
// @Path: ../libraries/AP_InertialSensor/AP_InertialSensor.cpp
GOBJECT(ins, "INS_", AP_InertialSensor),
#endif
#if CONFIG_HAL_BOARD == HAL_BOARD_AVR_SITL
// @Group: SIM_
// @Path: ../libraries/SITL/SITL.cpp
GOBJECT(sitl, "SIM_", SITL),
#endif
// @Group: AHRS_
// @Path: ../libraries/AP_AHRS/AP_AHRS.cpp
GOBJECT(ahrs, "AHRS_", AP_AHRS),
AP_VAREND
};
static void load_parameters(void)
{
if (!g.format_version.load() ||
g.format_version != Parameters::k_format_version) {
// erase all parameters
cliSerial->printf_P(PSTR("Firmware change: erasing EEPROM...\n"));
AP_Param::erase_all();
// save the current format version
g.format_version.set_and_save(Parameters::k_format_version);
cliSerial->println_P(PSTR("done."));
} else {
unsigned long before = micros();
// Load all auto-loaded EEPROM variables
AP_Param::load_all();
cliSerial->printf_P(PSTR("load_all took %luus\n"), micros() - before);
}
}
Reference in New Issue View Git Blame Copy Permalink