mirror of https://github.com/ArduPilot/ardupilot
148 lines
2.6 KiB
Plaintext
148 lines
2.6 KiB
Plaintext
# hw definition file for processing by chibios_hwdef.py
|
|
# for H743 bootloader
|
|
|
|
# MCU class and specific type
|
|
MCU STM32H7xx STM32H743xx
|
|
|
|
FULL_FEATURED_BOOTLOADER 1
|
|
|
|
# USB setup
|
|
USB_VENDOR 0x2DAE # ONLY FOR USE BY HEX! NOBODY ELSE
|
|
USB_PRODUCT 0x5011
|
|
USB_STRING_MANUFACTURER "CubePilot"
|
|
|
|
# setup build for a peripheral firmware
|
|
env AP_PERIPH 1
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 24000000
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 1037
|
|
|
|
FLASH_SIZE_KB 2048
|
|
|
|
# bootloader is installed at zero offset
|
|
FLASH_RESERVE_START_KB 0
|
|
|
|
# the location where the bootloader will put the firmware
|
|
# the H743 has 128k sectors
|
|
FLASH_BOOTLOADER_LOAD_KB 256
|
|
|
|
PB15 LED_2 OUTPUT LOW
|
|
PB14 LED OUTPUT LOW
|
|
|
|
# board voltage
|
|
STM32_VDD 330U
|
|
|
|
# order of UARTs (and USB)
|
|
SERIAL_ORDER OTG1 UART7
|
|
|
|
define HAL_NO_MONITOR_THREAD
|
|
|
|
# USART3 F9
|
|
PD9 USART3_RX USART3
|
|
PD8 USART3_TX USART3
|
|
|
|
# UART7 F9
|
|
PE7 UART7_RX UART7
|
|
PE8 UART7_TX UART7 NODMA
|
|
|
|
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
|
|
define USB_USE_WAIT TRUE
|
|
define HAL_USE_USB_MSD 1
|
|
|
|
define HAL_DEVICE_THREAD_STACK 2048
|
|
|
|
#define AP_PARAM_MAX_EMBEDDED_PARAM 0
|
|
|
|
define HAL_BARO_ALLOW_INIT_NO_BARO
|
|
|
|
define HAL_COMPASS_MAX_SENSORS 1
|
|
|
|
# GPS+MAG
|
|
define HAL_PERIPH_ENABLE_GPS
|
|
define HAL_PERIPH_ENABLE_MAG
|
|
|
|
# Add MAVLink
|
|
env FORCE_MAVLINK_INCLUDE 1
|
|
|
|
# enable CAN support
|
|
PB8 CAN1_RX CAN1
|
|
PB9 CAN1_TX CAN1
|
|
PB5 CAN2_RX CAN2
|
|
PB6 CAN2_TX CAN2
|
|
#PB5 GPIO_CAN1_SILENT OUTPUT PUSHPULL SPEED_LOW LOW
|
|
|
|
PF8 blank CS
|
|
SPIDEV profiled SPI5 DEVID1 blank MODE3 1*MHZ 1*MHZ
|
|
|
|
PE4 MPU_EXT_CS CS
|
|
PE2 SPI4_SCK SPI4
|
|
PE5 SPI4_MISO SPI4
|
|
PE6 SPI4_MOSI SPI4
|
|
|
|
|
|
PG15 spi6cs CS
|
|
PG13 SPI6_SCK SPI6
|
|
PG12 SPI6_MISO SPI6
|
|
PG14 SPI6_MOSI SPI6
|
|
|
|
PF7 SPI5_SCK SPI5
|
|
PF9 SPI5_MOSI SPI5
|
|
|
|
define BOARD_SER1_RTSCTS_DEFAULT 0
|
|
|
|
#gps f9
|
|
PD10 F91TXR INPUT
|
|
PD11 F92RST INPUT
|
|
PD13 F93SB INPUT
|
|
PD14 F94EXTINT INPUT
|
|
PD15 F95RSV1 INPUT
|
|
PG2 F97 INPUT GPIO(100)
|
|
PG3 F96RSV2 INPUT
|
|
PD4 RTKSTAT INPUT
|
|
PD5 GEOFENCESTAT INPUT
|
|
|
|
#others
|
|
PG10 can2int INPUT
|
|
PG11 can2sleep OUTPUT PUSHPULL SPEED_LOW LOW
|
|
PF1 GNDDET2 INPUT
|
|
PF2 GNDDET1 INPUT
|
|
PC6 EXTERN_GPIO1 OUTPUT GPIO(1)
|
|
PC7 EXTERN_GPIO2 OUTPUT GPIO(2)
|
|
#sensor enable
|
|
PC0 SENSEN OUTPUT HIGH
|
|
PB1 IMUINT INPUT
|
|
PB3 QCAN2TERM OUTPUT LOW GPIO(4)
|
|
PB4 QCAN2INT0 INPUT
|
|
PC13 QCAN1SLEEP OUTPUT PUSHPULL SPEED_LOW LOW
|
|
PE0 QCAN1INT INPUT
|
|
PE1 QCAN1INT0 INPUT
|
|
PE3 QCAN1INT1 INPUT
|
|
|
|
PD6 QCAN1TERM OUTPUT LOW GPIO(3)
|
|
PD7 QCAN2INT1 INPUT
|
|
PA8 QCAN12OSC1 INPUT
|
|
|
|
# This input pin is used to detect that power is valid on USB.
|
|
PA9 VBUS INPUT
|
|
PH13 VDD_33V_SENS INPUT
|
|
|
|
# This defines some input pins, currently unused.
|
|
PB2 BOOT1 INPUT
|
|
|
|
|
|
|
|
# passthrough CAN1
|
|
define HAL_DEFAULT_CPORT 1
|
|
|
|
FULL_CHIBIOS_BOOTLOADER 1
|