mirror of https://github.com/ArduPilot/ardupilot
128 lines
2.9 KiB
Plaintext
128 lines
2.9 KiB
Plaintext
# hw definition file for processing by chibios_pins.py
|
|
# hardware repository: https://github.com/ARK-Electronics/ARK_CANNODE
|
|
|
|
# MCU class and specific type
|
|
# note: the device is STM32F412CG, not all F412 pins are available
|
|
MCU STM32F4xx STM32F412Rx
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 83
|
|
|
|
env AP_PERIPH 1
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
# ChibiOS system timer
|
|
STM32_ST_USE_TIMER 5
|
|
|
|
# bootloader starts firmware at 64k
|
|
FLASH_RESERVE_START_KB 64
|
|
|
|
# 1Mb flash
|
|
FLASH_SIZE_KB 1024
|
|
|
|
# order of I2C buses
|
|
I2C_ORDER I2C1
|
|
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
|
|
# order of UARTs
|
|
SERIAL_ORDER USART1 USART2
|
|
|
|
# pin definitions
|
|
# Now we start defining some PWM pins. We also map these pins to GPIO
|
|
# values, so users can set SERVOx_FUNCTION=-1 to determine which
|
|
# PWM outputs on the primary MCU are set up as GPIOs.
|
|
# To match HAL_PX4 we number the GPIOs for the PWM outputs
|
|
# starting at 50.
|
|
PA0 TIM2_CH1 TIM2 PWM(1) GPIO(50) BIDIR
|
|
PA1 TIM2_CH2 TIM2 PWM(2) GPIO(51)
|
|
PB10 TIM2_CH3 TIM2 PWM(3) GPIO(52)
|
|
PB4 TIM3_CH1 TIM3 PWM(4) GPIO(53) BIDIR
|
|
PB5 TIM3_CH2 TIM3 PWM(5) GPIO(54)
|
|
PB0 TIM3_CH3 TIM3 PWM(6) GPIO(55)
|
|
PB1 TIM3_CH4 TIM3 PWM(7) GPIO(56) BIDIR
|
|
PB7 TIM4_CH2 TIM4 PWM(8) GPIO(58) NODMA # DMA would be shared with I2C
|
|
|
|
# USART1 GPS
|
|
PA15 USART1_TX USART1
|
|
PB3 USART1_RX USART1
|
|
|
|
# USART2 in debug connector
|
|
PA2 USART2_TX USART2
|
|
PA3 USART2_RX USART2
|
|
|
|
# SPI bus for IMU
|
|
PB2 MPU_DRDY INPUT
|
|
PA4 IMU1_CS CS
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
# LEDs
|
|
PA8 LED_R1 OUTPUT HIGH GPIO(0)
|
|
PA9 LED_G1 OUTPUT HIGH GPIO(1)
|
|
PA10 LED_B1 OUTPUT HIGH GPIO(2)
|
|
|
|
define HAL_GPIO_A_LED_PIN 0
|
|
define HAL_GPIO_B_LED_PIN 1
|
|
define HAL_GPIO_C_LED_PIN 2
|
|
|
|
define HAL_GPIO_LED_ON 0
|
|
define HAL_GPIO_LED_OFF 1
|
|
|
|
# use pixracer style 3-LED indicators
|
|
define HAL_HAVE_PIXRACER_LED
|
|
|
|
# CAN bus
|
|
PA11 CAN1_RX CAN1
|
|
PA12 CAN1_TX CAN1
|
|
PC14 GPIO_CAN1_SILENT OUTPUT PUSHPULL SPEED_LOW LOW
|
|
PC15 GPIO_CAN1_TERM OUTPUT PUSHPULL SPEED_LOW LOW
|
|
|
|
# pins for SWD debugging with a STlink or black-magic probe.
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# SPI1 FSYNC for ICM42688p
|
|
# PB8 TIM10_CH1 TIM10
|
|
|
|
# store parameters in pages 2 and 3
|
|
STORAGE_FLASH_PAGE 2
|
|
define HAL_STORAGE_SIZE 8192
|
|
|
|
# no ADC pins
|
|
define HAL_USE_ADC FALSE
|
|
|
|
# External SPI2
|
|
PB12 EXT_CS1 SPI2
|
|
PC13 EXT_CS2 SPI2
|
|
PB13 SPI2_SCK SPI2
|
|
PB14 SPI2_MISO SPI2
|
|
PB15 SPI2_MOSI SPI2
|
|
|
|
# I2C port
|
|
PB6 I2C1_SCL I2C1
|
|
PB9 I2C1_SDA I2C1
|
|
|
|
# SPI device table - can't yet use IMU in AP_Periph
|
|
#SPIDEV icm42688 SPI1 DEVID1 IMU1_CS MODE3 2*MHZ 8*MHZ
|
|
#IMU Invensensev3 SPI:icm42688 ROTATION_ROLL_180
|
|
|
|
define GPS_MAX_RECEIVERS 1
|
|
define GPS_MAX_INSTANCES 1
|
|
define HAL_COMPASS_MAX_SENSORS 1
|
|
define HAL_PERIPH_ENABLE_GPS
|
|
define HAL_PERIPH_ENABLE_MAG
|
|
define HAL_PERIPH_ENABLE_BARO
|
|
define HAL_PERIPH_ENABLE_RC_OUT
|
|
define HAL_PERIPH_ENABLE_NOTIFY
|
|
|
|
define CAN_APP_NODE_NAME "org.ardupilot.ARK_CANNODE"
|
|
|
|
# enable ESC control
|
|
define HAL_SUPPORT_RCOUT_SERIAL 1
|
|
define HAL_WITH_ESC_TELEM 1
|
|
define AP_SERIALLED_ENABLED 1
|