ardupilot/ArduCopter/mode_loiter.cpp

217 lines
7.5 KiB
C++

#include "Copter.h"
#if MODE_LOITER_ENABLED == ENABLED
/*
* Init and run calls for loiter flight mode
*/
// loiter_init - initialise loiter controller
bool ModeLoiter::init(bool ignore_checks)
{
if (!copter.failsafe.radio) {
float target_roll, target_pitch;
// apply SIMPLE mode transform to pilot inputs
update_simple_mode();
// convert pilot input to lean angles
get_pilot_desired_lean_angles(target_roll, target_pitch, loiter_nav->get_angle_max_cd(), attitude_control->get_althold_lean_angle_max_cd());
// process pilot's roll and pitch input
loiter_nav->set_pilot_desired_acceleration(target_roll, target_pitch);
} else {
// clear out pilot desired acceleration in case radio failsafe event occurs and we do not switch to RTL for some reason
loiter_nav->clear_pilot_desired_acceleration();
}
loiter_nav->init_target();
// initialise the vertical position controller
if (!pos_control->is_active_z()) {
pos_control->init_z_controller();
}
// set vertical speed and acceleration limits
pos_control->set_max_speed_accel_z(-get_pilot_speed_dn(), g.pilot_speed_up, g.pilot_accel_z);
pos_control->set_correction_speed_accel_z(-get_pilot_speed_dn(), g.pilot_speed_up, g.pilot_accel_z);
#if PRECISION_LANDING == ENABLED
_precision_loiter_active = false;
#endif
return true;
}
#if PRECISION_LANDING == ENABLED
bool ModeLoiter::do_precision_loiter()
{
if (!_precision_loiter_enabled) {
return false;
}
if (copter.ap.land_complete_maybe) {
return false; // don't move on the ground
}
// if the pilot *really* wants to move the vehicle, let them....
if (loiter_nav->get_pilot_desired_acceleration().length() > 50.0f) {
return false;
}
if (!copter.precland.target_acquired()) {
return false; // we don't have a good vector
}
return true;
}
void ModeLoiter::precision_loiter_xy()
{
loiter_nav->clear_pilot_desired_acceleration();
Vector2f target_pos, target_vel;
if (!copter.precland.get_target_position_cm(target_pos)) {
target_pos = inertial_nav.get_position_xy_cm();
}
// get the velocity of the target
copter.precland.get_target_velocity_cms(inertial_nav.get_velocity_xy_cms(), target_vel);
Vector2f zero;
Vector2p landing_pos = target_pos.topostype();
// target vel will remain zero if landing target is stationary
pos_control->input_pos_vel_accel_xy(landing_pos, target_vel, zero);
// run pos controller
pos_control->update_xy_controller();
}
#endif
// loiter_run - runs the loiter controller
// should be called at 100hz or more
void ModeLoiter::run()
{
float target_roll, target_pitch;
float target_yaw_rate = 0.0f;
float target_climb_rate = 0.0f;
// set vertical speed and acceleration limits
pos_control->set_max_speed_accel_z(-get_pilot_speed_dn(), g.pilot_speed_up, g.pilot_accel_z);
// process pilot inputs unless we are in radio failsafe
if (!copter.failsafe.radio) {
// apply SIMPLE mode transform to pilot inputs
update_simple_mode();
// convert pilot input to lean angles
get_pilot_desired_lean_angles(target_roll, target_pitch, loiter_nav->get_angle_max_cd(), attitude_control->get_althold_lean_angle_max_cd());
// process pilot's roll and pitch input
loiter_nav->set_pilot_desired_acceleration(target_roll, target_pitch);
// get pilot's desired yaw rate
target_yaw_rate = get_pilot_desired_yaw_rate(channel_yaw->norm_input_dz());
// get pilot desired climb rate
target_climb_rate = get_pilot_desired_climb_rate(channel_throttle->get_control_in());
target_climb_rate = constrain_float(target_climb_rate, -get_pilot_speed_dn(), g.pilot_speed_up);
} else {
// clear out pilot desired acceleration in case radio failsafe event occurs and we do not switch to RTL for some reason
loiter_nav->clear_pilot_desired_acceleration();
}
// relax loiter target if we might be landed
if (copter.ap.land_complete_maybe) {
loiter_nav->soften_for_landing();
}
// Loiter State Machine Determination
AltHoldModeState loiter_state = get_alt_hold_state(target_climb_rate);
// Loiter State Machine
switch (loiter_state) {
case AltHold_MotorStopped:
attitude_control->reset_rate_controller_I_terms();
attitude_control->reset_yaw_target_and_rate();
pos_control->relax_z_controller(0.0f); // forces throttle output to decay to zero
loiter_nav->init_target();
attitude_control->input_thrust_vector_rate_heading(loiter_nav->get_thrust_vector(), target_yaw_rate, false);
break;
case AltHold_Landed_Ground_Idle:
attitude_control->reset_yaw_target_and_rate();
FALLTHROUGH;
case AltHold_Landed_Pre_Takeoff:
attitude_control->reset_rate_controller_I_terms_smoothly();
loiter_nav->init_target();
attitude_control->input_thrust_vector_rate_heading(loiter_nav->get_thrust_vector(), target_yaw_rate, false);
pos_control->relax_z_controller(0.0f); // forces throttle output to decay to zero
break;
case AltHold_Takeoff:
// initiate take-off
if (!takeoff.running()) {
takeoff.start(constrain_float(g.pilot_takeoff_alt,0.0f,1000.0f));
}
// get avoidance adjusted climb rate
target_climb_rate = get_avoidance_adjusted_climbrate(target_climb_rate);
// set position controller targets adjusted for pilot input
takeoff.do_pilot_takeoff(target_climb_rate);
// run loiter controller
loiter_nav->update();
// call attitude controller
attitude_control->input_thrust_vector_rate_heading(loiter_nav->get_thrust_vector(), target_yaw_rate, false);
break;
case AltHold_Flying:
// set motors to full range
motors->set_desired_spool_state(AP_Motors::DesiredSpoolState::THROTTLE_UNLIMITED);
#if PRECISION_LANDING == ENABLED
bool precision_loiter_old_state = _precision_loiter_active;
if (do_precision_loiter()) {
precision_loiter_xy();
_precision_loiter_active = true;
} else {
_precision_loiter_active = false;
}
if (precision_loiter_old_state && !_precision_loiter_active) {
// prec loiter was active, not any more, let's init again as user takes control
loiter_nav->init_target();
}
// run loiter controller if we are not doing prec loiter
if (!_precision_loiter_active) {
loiter_nav->update();
}
#else
loiter_nav->update();
#endif
// call attitude controller
attitude_control->input_thrust_vector_rate_heading(loiter_nav->get_thrust_vector(), target_yaw_rate, false);
// get avoidance adjusted climb rate
target_climb_rate = get_avoidance_adjusted_climbrate(target_climb_rate);
// update the vertical offset based on the surface measurement
copter.surface_tracking.update_surface_offset();
// Send the commanded climb rate to the position controller
pos_control->set_pos_target_z_from_climb_rate_cm(target_climb_rate);
break;
}
// run the vertical position controller and set output throttle
pos_control->update_z_controller();
}
uint32_t ModeLoiter::wp_distance() const
{
return loiter_nav->get_distance_to_target();
}
int32_t ModeLoiter::wp_bearing() const
{
return loiter_nav->get_bearing_to_target();
}
#endif