mirror of https://github.com/ArduPilot/ardupilot
150 lines
3.1 KiB
Plaintext
150 lines
3.1 KiB
Plaintext
# hw definition file for f303 Matek CAN GPS
|
|
|
|
# MCU class and specific type
|
|
MCU STM32F303 STM32F303xC
|
|
|
|
# bootloader starts firmware at 26k
|
|
FLASH_RESERVE_START_KB 26
|
|
|
|
# store parameters in pages 11 and 12
|
|
STORAGE_FLASH_PAGE 11
|
|
define HAL_STORAGE_SIZE 800
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 1004
|
|
|
|
# setup build for a peripheral firmware
|
|
env AP_PERIPH 1
|
|
|
|
# enable watchdog
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
define CH_CFG_ST_FREQUENCY 1000
|
|
define CH_CFG_ST_TIMEDELTA 0
|
|
|
|
# assume the 256k flash part for now
|
|
FLASH_SIZE_KB 256
|
|
|
|
# a LED to flash
|
|
PA4 LED OUTPUT LOW
|
|
|
|
define HAL_CAN_POOL_SIZE 6000
|
|
|
|
# only one I2C bus in normal config
|
|
PB6 I2C1_SCL I2C1
|
|
PB7 I2C1_SDA I2C1
|
|
|
|
# no ADC driver
|
|
define HAL_USE_ADC FALSE
|
|
define STM32_ADC_USE_ADC1 FALSE
|
|
define HAL_DISABLE_ADC_DRIVER TRUE
|
|
|
|
define HAL_NO_GPIO_IRQ
|
|
define SERIAL_BUFFERS_SIZE 512
|
|
define PORT_INT_REQUIRED_STACK 64
|
|
|
|
# avoid timer and RCIN threads to save memory
|
|
define HAL_NO_RCIN_THREAD
|
|
|
|
define HAL_USE_RTC FALSE
|
|
define DISABLE_SERIAL_ESC_COMM TRUE
|
|
|
|
define DMA_RESERVE_SIZE 0
|
|
|
|
|
|
# MAIN_STACK is stack of initial thread
|
|
MAIN_STACK 0x300
|
|
|
|
# PROCESS_STACK controls stack for main thread
|
|
PROCESS_STACK 0xA00
|
|
define HAL_DISABLE_LOOP_DELAY
|
|
|
|
# enable CAN support
|
|
PA11 CAN_RX CAN
|
|
PA12 CAN_TX CAN
|
|
|
|
define HAL_CAN_RX_QUEUE_SIZE 32
|
|
|
|
define HAL_USE_I2C TRUE
|
|
define STM32_I2C_USE_I2C1 TRUE
|
|
|
|
define HAL_UART_MIN_TX_SIZE 256
|
|
define HAL_UART_MIN_RX_SIZE 128
|
|
|
|
define HAL_UART_STACK_SIZE 512
|
|
|
|
define STORAGE_THD_WA_SIZE 512
|
|
define IO_THD_WA_SIZE 512
|
|
|
|
|
|
# only one I2C bus
|
|
I2C_ORDER I2C1
|
|
|
|
define HAL_I2C_CLEAR_ON_TIMEOUT 0
|
|
|
|
define HAL_DEVICE_THREAD_STACK 512
|
|
|
|
define AP_PARAM_MAX_EMBEDDED_PARAM 512
|
|
|
|
define HAL_I2C_INTERNAL_MASK 1
|
|
|
|
# disable dual GPS and GPS blending to save flash space
|
|
define GPS_MAX_RECEIVERS 1
|
|
define GPS_MAX_INSTANCES 1
|
|
define HAL_COMPASS_MAX_SENSORS 1
|
|
|
|
|
|
|
|
# keep ROMFS uncompressed as we don't have enough RAM
|
|
# to uncompress the bootloader at runtime
|
|
env ROMFS_UNCOMPRESSED True
|
|
|
|
# order of UARTs
|
|
SERIAL_ORDER USART1 EMPTY USART3 USART2
|
|
|
|
# USART1, for debug
|
|
PA9 USART1_TX USART1 SPEED_HIGH NODMA
|
|
PA10 USART1_RX USART1 SPEED_HIGH NODMA
|
|
|
|
# USART2, connected to GPS
|
|
PA2 USART2_TX USART2 SPEED_HIGH NODMA
|
|
PA3 USART2_RX USART2 SPEED_HIGH NODMA
|
|
|
|
# USART3, for MSP
|
|
PB10 USART3_TX USART3 SPEED_HIGH
|
|
PB11 USART3_RX USART3 SPEED_HIGH
|
|
|
|
# use DNA for node allocation
|
|
|
|
# added QMC5883L mag on I2C
|
|
COMPASS QMC5883L I2C:0:0xd false ROTATION_PITCH_180_YAW_90
|
|
|
|
# I2C baro (DPS310)
|
|
BARO DPS310 I2C:0:0x76
|
|
|
|
# enable builtin GPS, mag and baro
|
|
# also allow for airspeed on i2c port, and rangefinder on MSP port
|
|
define HAL_PERIPH_ENABLE_GPS
|
|
define HAL_PERIPH_ENABLE_MAG
|
|
define HAL_PERIPH_ENABLE_BARO
|
|
define HAL_PERIPH_ENABLE_AIRSPEED
|
|
define HAL_PERIPH_ENABLE_RANGEFINDER
|
|
define HAL_PERIPH_ENABLE_MSP
|
|
|
|
# setup for MSP
|
|
define HAL_MSP_ENABLED 1
|
|
define AP_PERIPH_MSP_PORT_DEFAULT 2
|
|
|
|
# disable rangefinder by default
|
|
define AP_PERIPH_RANGEFINDER_PORT_DEFAULT -1
|
|
|
|
# the M8 GPS is good at 10Hz, but the M9 is better at 5Hz,
|
|
# so stick to 5Hz as the firmware is shared
|
|
define GPS_MAX_RATE_MS 200
|
|
|
|
# 10" DLVR sensor by default
|
|
define HAL_AIRSPEED_TYPE_DEFAULT 9
|
|
define AIRSPEED_MAX_SENSORS 1
|