Mirror
/
ardupilot
mirror of https://github.com/ArduPilot/ardupilot
5
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
ardupilot/libraries/AP_HAL_ChibiOS/hwdef/MambaF405v2
History
Peter Barker 0eacc0348e AP_HAL_ChibiOS: remove HAL_COMPASS_DEFAULT define 
this doesn't actually allow you to specify a default, despite the name
and a couple of hwdefs trying to use it that way.

This would have stopped being useful when we did the
compass-prority-table stuff - or before.
 		2022-02-01 12:10:38 +11:00
..
README.md AP_HAL_ChibiOS: Support for Diatone MambaF405 MK2 2020-12-16 19:07:07 +11:00
hwdef-bl.dat HAL_ChibiOS: removed boilerplate lines from bootloaders 2021-10-26 15:56:53 +11:00
hwdef.dat AP_HAL_ChibiOS: remove HAL_COMPASS_DEFAULT define 2022-02-01 12:10:38 +11:00
mamba_f405mk2_board.jpg AP_HAL_ChibiOS: Support for Diatone MambaF405 MK2 2020-12-16 19:07:07 +11:00
mamba_f405mk2_pinout.png AP_HAL_ChibiOS: Support for Diatone MambaF405 MK2 2020-12-16 19:07:07 +11:00

README.md

Mamba F405 MK2 Flight Controller

https://www.diatone.us/products/mamba-f405-flight-controller-mk2

The Mamba F405 MK2 is a flight controller produced by Diatone.

Features

  • STM32F405RGT6 microcontroller
  • MPU6000 IMU
  • AT7456E OSD
  • 4 UARTs
  • 4 PWM outputs

Pinout

Mamba F405 MK2 Board

UART Mapping

The UARTs are marked Rn and Tn in the above pinouts. The Rn pin is the receive pin for UARTn. The Tn pin is the transmit pin for UARTn.

Name Pin Function
SERIAL0 COMPUTER USB
SERIAL1 PPM/RX1/SBUS/TX1 UART1 (RC Input)
SERIAL3 TX3/RX3 UART3 (Telem1)
SERIAL6 TX6/RX6 UART6 (GPS)

RC Input

RC input is configured on the PPM (UART1_RX) pin. It supports all RC protocols. The S.BUS pad provides an inverted input for S.BUS receivers.

OSD Support

The Mamba F405 MK2 supports OSD using OSD_TYPE 1 (MAX7456 driver).

PWM Output

The Mamba F405 MK2 supports up to 4 PWM outputs. The pads for motor output ESC1 to ESC4 on the above diagram are for the 4 outputs. All 4 outputs support DShot as well as all PWM types.

The PWM are in one group.

Channels within the same group need to use the same output rate. If any channel in a group uses DShot then all channels in the group need to use DShot.

Battery Monitoring

The board has a builting voltage sensor. The voltage sensor can handle up to 6S LiPo batteries.

The correct battery setting parameters are:

  • BATT_MONITOR 3
  • BATT_VOLT_PIN 11
  • BATT_VOLT_MULT around 12.0
  • BATT_CURR_PIN 13
  • BATT_CURR_MULT around 39 with the included 40A ESC

Compass

The Mamba F405 MK2 does not have a builting compass, but you can attach an external compass using I2C on the SDA and SCL pads.

Alternate settings

It is possible to set alternate configurations with the BRD_ALT_CONFIG parameter.

BRD_ALT_CONFIG RX1 function
ALT 0(default) RCININT
ALT 1 RX1/TX1

Loading Firmware

Initial firmware load can be done with DFU by plugging in USB with the bootloader button pressed. Then you should load the "with_bl.hex" firmware, using your favourite DFU loading tool.

Once the initial firmware is loaded you can update the firmware using any ArduPilot ground station software. Updates should be done with the *.apj firmware files.