mirror of https://github.com/ArduPilot/ardupilot
125 lines
2.6 KiB
Plaintext
125 lines
2.6 KiB
Plaintext
# hw definition file for processing by chibios_pins.py
|
|
# for crazyflie2.0 hardware (see bitcraze.io)
|
|
|
|
# MCU class and specific type
|
|
MCU STM32F4xx STM32F405xx
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 12
|
|
|
|
define CONFIG_HAL_BOARD_SUBTYPE HAL_BOARD_SUBTYPE_CHIBIOS_CRAZYFLIE2
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 8000000
|
|
STM32_PLLM_VALUE 8
|
|
|
|
define STM32_ST_USE_TIMER 5
|
|
|
|
FLASH_SIZE_KB 1024
|
|
|
|
# board voltage
|
|
STM32_VDD 330U
|
|
|
|
# use USB for stdout
|
|
#STDOUT_SERIAL SD3
|
|
#STDOUT_BAUDRATE 57600
|
|
|
|
# usart2
|
|
PA2 USART2_TX USART2 # E_TX2
|
|
PA3 USART2_RX USART2 # E_RX2
|
|
|
|
# external SPI on SPI1
|
|
PA5 SPI1_SCK SPI1 # E_SCK
|
|
PA6 SPI1_MISO SPI1 # E_MISO
|
|
PA7 SPI1_MOSI SPI1 # E_MOSI
|
|
|
|
# I2C3 is for IMU
|
|
PA8 I2C3_SCL I2C3
|
|
PC9 I2C3_SDA I2C3
|
|
|
|
# USB port
|
|
PA10 USB_ID INPUT
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
# stlink/jtag
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
PA1 TIM2_CH2 TIM2 PWM(1) # front-right
|
|
PB11 TIM2_CH4 TIM2 PWM(4) # rear-right
|
|
PA15 TIM2_CH1 TIM2 PWM(2) # rear-left
|
|
PB9 TIM4_CH4 TIM4 PWM(3) # front-left
|
|
|
|
PC13 MPU_INT INPUT
|
|
PC14 MPU_FSYNC OUTPUT LOW
|
|
|
|
# LEDs
|
|
PD2 LED_BLUE OUTPUT HIGH
|
|
PC0 LED_RED_L OUTPUT HIGH
|
|
PC1 LED_GREEN_L OUTPUT HIGH
|
|
PC2 LED_GREEN_R OUTPUT HIGH
|
|
PC3 LED_RED_R OUTPUT HIGH
|
|
|
|
# misc pins, unused
|
|
#PH0 OSC_IN
|
|
#PH1 OSC_OUT
|
|
#PB2 BOOT1
|
|
# PB3 STM_SWO
|
|
|
|
# CS pins for external SPI devices
|
|
PC12 E_CS0 CS
|
|
PB4 E_CS1 CS
|
|
PB5 E_CS2 CS
|
|
PB8 E_CS3 CS
|
|
|
|
# external I2C on I2C1
|
|
PB6 I2C1_SCL I2C1 # E_SCL
|
|
PB7 I2C1_SDA I2C1 # E_SCL
|
|
|
|
# radio setup
|
|
PA4 NRF_FLOW_CTRL INPUT # goes low when we can write to uart
|
|
#PB13 NRF_SWCLK
|
|
#PB15 NRF_SWIO
|
|
PC6 USART6_TX USART6 # NRF_RT
|
|
PC7 USART6_RX USART6 # NRF_RX
|
|
|
|
# USART3 for telemetry
|
|
PC10 USART3_TX USART3 # E_TX1
|
|
PC11 USART3_RX USART3 # E_RX1
|
|
|
|
# setup I2C order
|
|
I2C_ORDER I2C3 I2C1
|
|
|
|
# we need I2C clock at 400kHz for IMU
|
|
define HAL_I2C_MAX_CLOCK 400000
|
|
|
|
# order of UARTs (and USB)
|
|
UART_ORDER OTG1 USART2 USART3 USART6
|
|
|
|
define HAL_STORAGE_SIZE 15360
|
|
define STORAGE_FLASH_PAGE 1
|
|
|
|
# reserve 32k for bootloader and 32k for flash storage
|
|
FLASH_RESERVE_START_KB 64
|
|
|
|
define HAL_INS_DEFAULT HAL_INS_MPU60XX_I2C
|
|
define HAL_INS_DEFAULT_ROTATION ROTATION_YAW_180
|
|
define HAL_INS_MPU60x0_I2C_BUS 0
|
|
define HAL_INS_MPU60x0_I2C_ADDR 0x69
|
|
|
|
define HAL_BARO_DEFAULT HAL_BARO_LPS25H_IMU_I2C
|
|
define HAL_BARO_LPS25H_I2C_BUS 0
|
|
define HAL_BARO_LPS25H_I2C_ADDR 0x5D
|
|
define HAL_BARO_LPS25H_I2C_IMU_ADDR HAL_INS_MPU60x0_I2C_ADDR
|
|
|
|
# no built-in compass, but probe the i2c bus for all possible
|
|
# external compass types
|
|
define ALLOW_ARM_NO_COMPASS
|
|
define HAL_COMPASS_DEFAULT HAL_COMPASS_NONE
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
define HAL_COMPASS_AUTO_ROT_DEFAULT 2
|
|
|
|
define MAG_BOARD_ORIENTATION ROTATION_YAW_180
|