mirror of https://github.com/ArduPilot/ardupilot
131 lines
3.0 KiB
Plaintext
131 lines
3.0 KiB
Plaintext
# hw definition for Sierra-F405
|
|
|
|
# MCU class and specific type
|
|
MCU STM32F4xx STM32F405xx
|
|
|
|
# bootloader starts firmware at 64k
|
|
FLASH_RESERVE_START_KB 64
|
|
FLASH_SIZE_KB 1024
|
|
|
|
# store parameters in pages 2 and 3
|
|
STORAGE_FLASH_PAGE 2
|
|
define HAL_STORAGE_SIZE 15360
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 1052
|
|
|
|
env AP_PERIPH 1
|
|
|
|
define STM32_ST_USE_TIMER 5
|
|
define CH_CFG_ST_RESOLUTION 32
|
|
|
|
# enable watchdog
|
|
define HAL_WATCHDOG_ENABLED_DEFAULT true
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 16000000
|
|
|
|
STDOUT_SERIAL SD1
|
|
STDOUT_BAUDRATE 57600
|
|
|
|
define HAL_NO_GPIO_IRQ
|
|
|
|
# avoid timer and RCIN threads to save memory
|
|
define HAL_NO_RCIN_THREAD
|
|
|
|
define HAL_USE_RTC FALSE
|
|
|
|
define DMA_RESERVE_SIZE 0
|
|
|
|
define HAL_DISABLE_LOOP_DELAY
|
|
define HAL_NO_MONITOR_THREAD
|
|
define HAL_NO_LOGGING
|
|
define DISABLE_SERIAL_ESC_COMM TRUE
|
|
|
|
define HAL_DEVICE_THREAD_STACK 768
|
|
|
|
# we setup a small defaults.parm
|
|
define AP_PARAM_MAX_EMBEDDED_PARAM 256
|
|
|
|
# keep ROMFS uncompressed as we don't have enough RAM
|
|
# to uncompress the bootloader at runtime
|
|
env ROMFS_UNCOMPRESSED True
|
|
|
|
|
|
# --------------------- SPI2 RM3100 + DPS310 --------------------
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PA7 SPI1_MOSI SPI1
|
|
PA8 BARO_CS CS
|
|
PB12 MAG_CS CS
|
|
|
|
# ---------------------- CAN bus -------------------------
|
|
PA11 CAN1_RX CAN1
|
|
PA12 CAN1_TX CAN1
|
|
|
|
CAN_ORDER 1
|
|
|
|
# use DNA for node allocation
|
|
|
|
define CAN_APP_NODE_NAME "org.ardupilot.Sierra-F405"
|
|
|
|
# order of UARTs
|
|
SERIAL_ORDER USART1 EMPTY EMPTY USART2
|
|
|
|
# USART1 for debug
|
|
PA9 USART1_TX USART1
|
|
PA10 USART1_RX USART1
|
|
define HAL_SERIAL0_BAUD_DEFAULT 57600
|
|
|
|
# USART2 M9N
|
|
PA2 USART2_TX USART2 SPEED_HIGH
|
|
PA3 USART2_RX USART2 SPEED_HIGH
|
|
|
|
# --------------------- CAM Trigger + Feedback -----------------------
|
|
PB8 TIM4_CH3 TIM4 PWM(1) GPIO(50)
|
|
PB9 TIM4_CH4 TIM4 PWM(2) GPIO(51)
|
|
|
|
# WS2812 LED pin
|
|
PA15 TIM2_CH1 TIM2 PWM(3) GPIO(52)
|
|
PB4 TIM3_CH1 TIM3 PWM(4) GPIO(53)
|
|
|
|
# ----------------------- GPS ----------------------------
|
|
define HAL_PERIPH_ENABLE_GPS
|
|
define HAL_PERIPH_GPS_PORT_DEFAULT 3
|
|
define GPS_MAX_RECEIVERS 1
|
|
define GPS_MAX_INSTANCES 1
|
|
|
|
# ---------------------- COMPASS ---------------------------
|
|
define HAL_PERIPH_ENABLE_MAG
|
|
|
|
SPIDEV rm3100 SPI1 DEVID1 MAG_CS MODE0 1*MHZ 1*MHZ
|
|
COMPASS RM3100 SPI:rm3100 false ROTATION_PITCH_180
|
|
define AP_RM3100_REVERSAL_MASK 7
|
|
define HAL_COMPASS_MAX_SENSORS 1
|
|
|
|
# --------------------- DPS310 ---------------------------
|
|
define HAL_PERIPH_ENABLE_BARO
|
|
SPIDEV dps310 SPI1 DEVID3 BARO_CS MODE3 5*MHZ 5*MHZ
|
|
BARO DPS310 SPI:dps310
|
|
|
|
define HAL_USE_ADC TRUE
|
|
define STM32_ADC_USE_ADC1 TRUE
|
|
#define HAL_DISABLE_ADC_DRIVER TRUE
|
|
PA0 VSENSE ADC1 SCALE(2)
|
|
|
|
# -------------------- Buzzer+NeoPixels --------------------
|
|
define HAL_PERIPH_ENABLE_RC_OUT
|
|
define HAL_PERIPH_ENABLE_NOTIFY
|
|
|
|
# Enable the sensor voltage pin
|
|
PC13 VDD_3V3_SENSORS_EN OUTPUT HIGH
|
|
|
|
#GPS M9N
|
|
PC11 M9EXTINT INPUT
|
|
PC10 M9RST INPUT
|
|
PC8 GPS_PPS_IN INPUT
|
|
PC7 M9SB INPUT
|
|
|
|
# allow for reboot command for faster development
|
|
define HAL_PERIPH_LISTEN_FOR_SERIAL_UART_REBOOT_CMD_PORT 0
|