mirror of https://github.com/ArduPilot/ardupilot
130 lines
8.3 KiB
Plaintext
130 lines
8.3 KiB
Plaintext
ArduCopter Release Notes:
|
|
------------------------------------------------------------------
|
|
ArduCopter 2.9.1b 30-Feb-2013
|
|
Improvements over 2.9.1:
|
|
1) reduce INS_MPU6K_FILTER to 20hz
|
|
2) reduce InertialNav Z-axis time constant to 5 (was 7)
|
|
3) increased max InertialNav accel correction to 3 m/s (was 1m/s)
|
|
4) bug fix for alt_hold being passed as int16_t to get_throttle_althold_with_slew
|
|
5) bug fix for throttle after acro flip (was being kept at min throttle if pilot switched out of ACRO mode while inverted)
|
|
6) reduce yaw_rate P default to 0.20 (was 0.25)
|
|
|
|
------------------------------------------------------------------
|
|
ArduCopter 2.9.1 & 2.9.1-rc2 01-Feb-2013
|
|
Improvements over 2.9.1-rc1:
|
|
1) small corretion to use of THR_MID to scale lower end of manual throttle between THR_MIN and 500 instead of 0 and 500
|
|
2) bug fix for longitude scaling being incorrectly calculated using Next Waypoint instead of home which could lead to scaling being 1
|
|
3) ESC calibration change to set update rate to ESCs to 50hz to allow simonk ESC to be calibrated
|
|
------------------------------------------------------------------
|
|
ArduCopter 2.9.1-rc1 31-Jan-2013
|
|
Improvements over 2.9:
|
|
1) THR_MID parameter added to allow users to adjust the manual throttle so that vehicle hovers at about mid stick
|
|
2) bug fix for autotrim - roll axis was backwards
|
|
3) bug fix to set sonar_alt_health to zero when sonar is disabled
|
|
4) capture level roll and pitch trims as part of accel calibration
|
|
5) bug fix to ppm encoder false positives
|
|
------------------------------------------------------------------
|
|
ArduCopter 2.9 & 2.9-rc5 14-Jan-2013
|
|
Improvements over 2.9-rc4:
|
|
1) add constraint to loiter commanded roll and pitch angles
|
|
2) relax altitude requirement for take-off command to complete
|
|
------------------------------------------------------------------
|
|
ArduCopter 2.9-rc4 12-Jan-2013
|
|
Improvements over 2.9-rc3:
|
|
1) Smoother transition between manual and auto flight modes (Leonard)
|
|
2) bug fix for LAND not actually landing when initiated from failsafe (Randy/Craig)
|
|
------------------------------------------------------------------
|
|
ArduCopter 2.9-rc3 11-Jan-2013
|
|
Improvements over 2.9-rc2:
|
|
1) alt hold with sonar improvements - now on by default (Leonard/Randy)
|
|
2) performance and memory useage improvements (Tridge/Randy)
|
|
3) increase APM1 baro pressure read from 5hz to 8.3hz to improve alt hold (Randy)
|
|
4) bug fix: altitude error reported to GCS (Randy)
|
|
5) limit inertial nav's max accel offset correction to 100cm/s/s to speed up recovery after hard impacts (Randy)_
|
|
6) moved rate controllers to run after ins read (Tridge/Randy)
|
|
------------------------------------------------------------------
|
|
ArduCopter 2.9-rc2 31-Dec-2012
|
|
Improvements over 2.9-rc1:
|
|
1) increased throttle rate gains from 1.0 to 6.0
|
|
2) APM1 fix so it works with inertial nav (5hz update rate of baro was beyond the tolerance set in the inav library)
|
|
------------------------------------------------------------------
|
|
ArduCopter 2.9-rc1 23-Dec-2012
|
|
Improvements over 2.8.1:
|
|
1) altitude hold improvements:
|
|
a)inertial navigation for vertical axis [Randy/Jonathan/Leonard/Jason]
|
|
b)accel based throttle controller [Leonard/Randy]
|
|
c)accelerometer calibration routine updated to use gauss-newton method [Randy/Tridge/Rolfe Schmidt]
|
|
d)parameters to control climb rate:
|
|
AUTO_VELZ_MIN, AUTO_VELZ_MAX - allows you to control the maximum climb and descent rates of the autopilot (in cm/s)
|
|
PILOT_VELZ_MAX - allows you to control the maximum climb/descent rate when in alt hold or loiter (in cm/s)
|
|
2) landing improvements [Leonard/Randy]
|
|
LAND_SPEED - allows you to set the landing speed in cm/s
|
|
3) camera related improvements:
|
|
a) AP_Relay enabled for APM2 and integrated with AP_Camera [Sandro Benigno]
|
|
b) camera trigger with channel 7 switch or DO_DIGICAM_CONTROL mission command [Randy]
|
|
c) allow yaw override by pilot or with CONDITIONAL_YAW command during missions [Randy]
|
|
YAW_OVR_BEHAVE - Controls when autopilot takes back normal control of yaw after pilot overrides (0=after next wp, 1=never)
|
|
4) trad heli improvements [Rob]
|
|
a) code tested and brought back into the fold (2.8.1 was never released for trad helis)
|
|
b) enabled rate controller (previously only used angle controllers)
|
|
c) fix to rotor speed controllers - now operates by switching off channel 8
|
|
d) allow wider collective pitch range in acro and alt hold modes vs stabilize mode
|
|
e) removed angle boost function because it created more problems than it solved
|
|
f) bug fix to allow collective pitch to use the entire range of servos
|
|
5) mediatek gps driver improvements [Craig]
|
|
a) added support for 1.9 firmware
|
|
b) bug fix to start-up routine so sbas can be enabled
|
|
6) failsafe improvements (both throttle and battery) [Randy/Craig/John Arne Birkeland]
|
|
a) RTL will not trigger if your throttle is zero - reduces risk of accidentally invoking RTL if you switch off your receiver before disarming
|
|
b) failsafe triggered in unlikely case of a PPM encoder failure
|
|
c) bug fix to resolve motors momentarily reducing to zero after failsafe is triggered
|
|
7) mpu6k filtering made configurable and default changed to 42hz for copters [Leonard/Tridge]
|
|
8) support ppm sum for transmitters with as few as 5 channels [Randy/John Arne Birkeland]
|
|
9) acro trainer - copter will return to be generally upright if you release the sticks in acro mode [Leonard]
|
|
ACRO_BAL_ROLL, ACRO_BAL_PITCH - controls rate at which roll returns to level
|
|
ACRO_TRAINER - 1 to enable the auto-bring-upright feature
|
|
10) other changes and bug fixes:
|
|
a) allow >45 degrees when in stabilize mode by adding lines like below to APM_Config (compile time option only) [Jason]
|
|
#define MAX_INPUT_ROLL_ANGLE 6000 // 60 degrees
|
|
#define MAX_INPUT_PITCH_ANGLE 6000 // 60 degrees
|
|
b) bug fix to stop RTL from ever climbing to an unreasonable height (i.e. >80m) [Jason]
|
|
c) event and state logging [Jason]
|
|
d) allow cli to be used over telemetry link [Tridge]
|
|
e) bug fix to allow compass accumulate to run when we have spare cpu cycles [Randy]
|
|
f) bug fix so do_set_servo command works [Randy]
|
|
g) bug fix to PID controller's so they don't calculate crazy D term on the first call [Tridge]
|
|
h) bug fix to initialise navigation parameter to resolve twitch when entering some navigation modes [Jason]
|
|
i) performance improvement to copter leds - use DigitalFastWrite and DigitalFastRead instead of native arduino functions [Randy]
|
|
j) removed unused stab_d from roll and pitch controller [Jason]
|
|
k) bug fix for guided mode not reaching target altitude if it reaches horizontal target first [Randy]
|
|
l) code clean-up, parameter documentation improvements [Randy/Jason/Rob/others]
|
|
|
|
------------------------------------------------------------------
|
|
ArduCopter 2.8.1 22-Oct-2012
|
|
Improvements over 2.8:
|
|
- 430 bytes of RAM freed up to resolve APM1 level issue and reduce chance of memory corruption on both APM1 and APM2
|
|
|
|
Improvements over 2.7.3:
|
|
- Improved ACRO mode (Leonard Hall)
|
|
- Improved stability patch to reduce "climb-on-yaw" problem (Leonard, Rob Lefebvre, Randy)
|
|
- Rate controller targets moved to body frames (yaw control now works properly when copter is inverted) (Leonard/Randy)
|
|
- Less bouncy Stabilize yaw control (Leonard)
|
|
- OpticalFlow sensor support for APM2.5 (Randy)
|
|
- DMP works again by adding "#define DMP_ENABLED ENABLED" to APM_Config.h You can also log DMP vs DCM to the dataflash by adding "#define SECONDARY_DMP_ENABLED ENABLED" (Randy)
|
|
- Watch dog added to shutdown motors if main loop feezes for 2 seconds (Randy)
|
|
- Thrust curve added to linearize pwm->thrust. Removes deadzone found above 90% throttle in most ESC/motors (Randy)
|
|
- More timing improvements (main loop is now tied to MPU6000s interrupt) (Randy)
|
|
- GPS NMEA bug fix (Alexey Kozin)
|
|
- Logging improvements (log I terms, dump all settings at head of dataflash log) (Jason)
|
|
|
|
Bug Fixes / Parameter changes:
|
|
- fixed skipping of last waypoint (Jason)
|
|
- resolved twitching when no GPS attached (Tridge)
|
|
- fixed loss of altitude if alt hold is engaged before first GPS lock (Randy/Jason)
|
|
- moved Roll-Pitch I terms from Stabilize controllers to Rate controllers
|
|
- TILT_COMPENSATION param tuned for TradHeli (Rob)
|
|
|
|
Code Cleanup:
|
|
- HAL changes for platform portability (Pat Hickey)
|
|
- Removed INSTANT_PWM (Randy)
|
|
------------------------------------------------------------------ |