mirror of https://github.com/ArduPilot/ardupilot
128 lines
2.6 KiB
Plaintext
128 lines
2.6 KiB
Plaintext
# hw definition file for processing by chibios_pins.py
|
|
# hardware repository: https://github.com/ARK-Electronics/ARK_GPS
|
|
|
|
# MCU class and specific type
|
|
# note: the device is STM32F412CE, not all F412 pins are available
|
|
MCU STM32F4xx STM32F412Rx
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 81
|
|
|
|
env AP_PERIPH 1
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
# ChibiOS system timer
|
|
STM32_ST_USE_TIMER 5
|
|
|
|
# bootloader starts firmware at 64k
|
|
FLASH_RESERVE_START_KB 64
|
|
|
|
# assume 512k flash size
|
|
FLASH_SIZE_KB 512
|
|
|
|
# order of I2C buses
|
|
I2C_ORDER I2C1 I2C2
|
|
|
|
define HAL_I2C_INTERNAL_MASK 3
|
|
|
|
# order of UARTs
|
|
# SERIAL_ORDER can be empty - only used to update firmware with uart in addition to can
|
|
SERIAL_ORDER USART2 USART1
|
|
|
|
|
|
# pin definitions
|
|
# PWM output for buzzer
|
|
PA0 TIM2_CH1 TIM2 GPIO(77) LOW ALARM
|
|
|
|
# safety LED, active low
|
|
PA1 SAFE_LED OUTPUT HIGH
|
|
define SAFE_LED_ON 0
|
|
|
|
# USART1 for GPS
|
|
PA15 USART1_TX USART1
|
|
PB3 USART1_RX USART1
|
|
|
|
# USART2 debug
|
|
PA2 USART2_TX USART2
|
|
PA3 USART2_RX USART2
|
|
|
|
# SPI bus
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
# LEDs
|
|
PA8 LED_R1 OUTPUT OPENDRAIN HIGH GPIO(0)
|
|
PA9 LED_G1 OUTPUT OPENDRAIN LOW GPIO(1)
|
|
PA10 LED_B1 OUTPUT OPENDRAIN LOW GPIO(2)
|
|
|
|
define AP_NOTIFY_GPIO_LED_RGB_RED_PIN 0
|
|
define AP_NOTIFY_GPIO_LED_RGB_GREEN_PIN 1
|
|
define AP_NOTIFY_GPIO_LED_RGB_BLUE_PIN 2
|
|
|
|
# use pixracer style 3-LED indicators
|
|
define AP_NOTIFY_GPIO_LED_RGB_ENABLED 1
|
|
|
|
# CAN bus
|
|
PA11 CAN1_RX CAN1
|
|
PA12 CAN1_TX CAN1
|
|
|
|
# pins for SWD debugging with a STlink or black-magic probe.
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# CS and DRDY
|
|
PB0 MPU_CS CS
|
|
PB1 MPU_DRDY INPUT
|
|
|
|
# I2C bus for magnetometer
|
|
PB6 I2C1_SCL I2C1
|
|
PB7 I2C1_SDA I2C1
|
|
|
|
# SPI1 FSYNC for ICM42688p
|
|
# PB8 TIM10_CH1 TIM10
|
|
|
|
# I2C bus for barometer
|
|
PB9 I2C2_SDA I2C2
|
|
PB10 I2C2_SCL I2C2
|
|
|
|
PB12 GPIO_CAN1_SILENT OUTPUT PUSHPULL SPEED_LOW LOW
|
|
PB13 GPIO_CAN1_TERM OUTPUT PUSHPULL SPEED_LOW LOW
|
|
|
|
# magnetometer
|
|
COMPASS BMM150 I2C:0:0x10 false ROTATION_NONE
|
|
|
|
# barometer
|
|
BARO BMP388 I2C:1:0x76
|
|
|
|
# store parameters in pages 2 and 3
|
|
STORAGE_FLASH_PAGE 2
|
|
define HAL_STORAGE_SIZE 8192
|
|
|
|
# no ADC pins
|
|
define HAL_USE_ADC FALSE
|
|
|
|
# safety button
|
|
PB15 SAFE_BUTTON INPUT PULLDOWN
|
|
|
|
define GPS_MAX_RECEIVERS 1
|
|
define GPS_MAX_INSTANCES 1
|
|
define HAL_COMPASS_MAX_SENSORS 1
|
|
define HAL_PERIPH_ENABLE_GPS
|
|
define HAL_PERIPH_ENABLE_MAG
|
|
define HAL_PERIPH_ENABLE_BARO
|
|
define HAL_PERIPH_ENABLE_BUZZER
|
|
define HAL_PERIPH_ENABLE_RC_OUT
|
|
define HAL_PERIPH_ENABLE_NOTIFY
|
|
|
|
# GPS on 2nd port
|
|
define HAL_PERIPH_GPS_PORT_DEFAULT 1
|
|
|
|
|
|
define HAL_SERIAL_ESC_COMM_ENABLED 1
|
|
define HAL_RCIN_THREAD_ENABLED 1
|
|
define HAL_SCHEDULER_LOOP_DELAY_ENABLED 1
|
|
define HAL_MONITOR_THREAD_ENABLED 1
|