mirror of https://github.com/ArduPilot/ardupilot
81 lines
1.6 KiB
PHP
81 lines
1.6 KiB
PHP
|
|
# USB setup
|
|
USB_VENDOR 0x2DAE # ONLY FOR USE BY HEX! NOBODY ELSE
|
|
USB_PRODUCT 0x1016
|
|
USB_STRING_MANUFACTURER "Hex/ProfiCNC"
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 24000000
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 140
|
|
|
|
FLASH_SIZE_KB 2048
|
|
|
|
# bootloader is installed at zero offset
|
|
FLASH_RESERVE_START_KB 0
|
|
|
|
# the location where the bootloader will put the firmware
|
|
# the H743 has 128k sectors
|
|
FLASH_BOOTLOADER_LOAD_KB 128
|
|
|
|
define HAL_LED_ON 0
|
|
|
|
# order of UARTs (and USB)
|
|
SERIAL_ORDER OTG1 USART2 USART3 UART7
|
|
|
|
PE12 LED_BOOTLOADER OUTPUT HIGH OPENDRAIN
|
|
|
|
# telem1
|
|
PD5 USART2_TX USART2
|
|
PD6 USART2_RX USART2
|
|
|
|
# telem2
|
|
PD8 USART3_TX USART3
|
|
PD9 USART3_RX USART3
|
|
|
|
# UART7 maps to SERIAL5.
|
|
PE7 UART7_RX UART7
|
|
PE8 UART7_TX UART7
|
|
|
|
# Pin for PWM Voltage Selection
|
|
PB4 PWM_VOLT_SEL OUTPUT HIGH
|
|
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# Add CS pins to ensure they are high in bootloader
|
|
PC1 MAG_CS CS
|
|
PC2 MPU_CS CS
|
|
PC13 GYRO_EXT_CS CS
|
|
PC14 BARO_EXT_CS CS
|
|
PC15 ACCEL_EXT_CS CS
|
|
PD7 BARO_CS CS
|
|
PE4 MPU_EXT_CS CS
|
|
PD10 FRAM_CS CS SPEED_VERYLOW
|
|
|
|
# disable peripheral and sensor power in the bootloader
|
|
PE3 VDD_3V3_SENSORS_EN OUTPUT LOW
|
|
PA8 nVDD_5V_PERIPH_EN OUTPUT LOW
|
|
|
|
# enable DFU by default
|
|
ENABLE_DFU_BOOT 1
|
|
|
|
# enable flashing from SD card:
|
|
include sdcard.inc
|
|
# enable FAT filesystem support (needs a microSD defined via SDMMC)
|
|
define HAL_OS_FATFS_IO 1
|
|
define AP_BOOTLOADER_FLASH_FROM_SD_ENABLED 1
|
|
|
|
# FATFS support:
|
|
define CH_CFG_USE_MEMCORE 1
|
|
define CH_CFG_USE_HEAP 1
|
|
define CH_CFG_USE_SEMAPHORES 0
|
|
define CH_CFG_USE_MUTEXES 1
|
|
define CH_CFG_USE_DYNAMIC 1
|
|
define CH_CFG_USE_WAITEXIT 1
|
|
define CH_CFG_USE_REGISTRY 1
|