mirror of https://github.com/ArduPilot/ardupilot
142 lines
2.5 KiB
Plaintext
142 lines
2.5 KiB
Plaintext
# hw definition file for Zubax GNSS
|
|
|
|
# MCU class and specific type
|
|
MCU STM32F105 STM32F105xC
|
|
|
|
define STM32F107_MCUCONF
|
|
|
|
define HAL_BOARD_AP_PERIPH_ZUBAXGNSS
|
|
|
|
# bootloader starts firmware at 34k
|
|
FLASH_RESERVE_START_KB 34
|
|
|
|
# store parameters in last 2 pages
|
|
STORAGE_FLASH_PAGE 126
|
|
define HAL_STORAGE_SIZE 800
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 1005
|
|
|
|
# setup build for a peripheral firmware
|
|
env AP_PERIPH 1
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 16000000
|
|
|
|
define CH_CFG_ST_FREQUENCY 1000
|
|
|
|
FLASH_SIZE_KB 256
|
|
|
|
# USART3 for debug
|
|
STDOUT_SERIAL SD3
|
|
STDOUT_BAUDRATE 115200
|
|
|
|
|
|
# enable pin for GPS
|
|
PB7 GPS_ENABLE OUTPUT HIGH
|
|
|
|
PA15 BARO_CS CS
|
|
PD2 MAG_CS CS
|
|
PB6 MAG_DRDY INPUT
|
|
|
|
PC1 HWID_BIT0 INPUT
|
|
PC2 HWID_BIT1_INV INPUT
|
|
PC3 HWID_BIT2 INPUT
|
|
|
|
PB3 LED OUTPUT
|
|
PB5 LED_CAN1 OUTPUT
|
|
PB4 LED_CAN2 OUTPUT
|
|
|
|
# USART2 for GPS
|
|
PA2 USART2_TX USART2 SPEED_HIGH NODMA
|
|
PA3 USART2_RX USART2 SPEED_HIGH NODMA
|
|
|
|
# USART3 for debug
|
|
PB10 USART3_TX USART3 SPEED_HIGH NODMA
|
|
PB11 USART3_RX USART3 SPEED_HIGH NODMA
|
|
|
|
# PA13 XPA13 OUTPUT HIGH
|
|
# PA1 XPA1 INPUT FLOATING
|
|
|
|
# don't enable DMA in UART driver
|
|
define HAL_UART_NODMA
|
|
|
|
# enable watchdog
|
|
|
|
# enable CAN support
|
|
PA11 CAN_RX CAN
|
|
PB9 CAN_TX CAN
|
|
|
|
|
|
|
|
# no I2C buses
|
|
# I2C_ORDER
|
|
|
|
# spi bus for baro/mag
|
|
PC10 SPI3_SCK SPI3 SPEED_HIGH
|
|
PC11 SPI3_MISO SPI3 SPEED_HIGH
|
|
PC12 SPI3_MOSI SPI3 SPEED_HIGH
|
|
|
|
#########################
|
|
# order of UARTs
|
|
SERIAL_ORDER USART3 EMPTY EMPTY USART2
|
|
|
|
SPIDEV ms5611 SPI3 DEVID1 BARO_CS MODE3 8*MHZ 8*MHZ
|
|
SPIDEV lis3mdl SPI3 DEVID2 MAG_CS MODE3 500*KHZ 500*KHZ
|
|
|
|
define HAL_USE_ADC FALSE
|
|
define STM32_ADC_USE_ADC1 FALSE
|
|
define HAL_DISABLE_ADC_DRIVER TRUE
|
|
|
|
define HAL_NO_GPIO_IRQ
|
|
|
|
define CH_CFG_ST_TIMEDELTA 0
|
|
define SERIAL_BUFFERS_SIZE 512
|
|
define PORT_INT_REQUIRED_STACK 64
|
|
|
|
#defined to turn off undef warnings
|
|
define __FPU_PRESENT 0
|
|
|
|
define HAL_USE_RTC FALSE
|
|
|
|
define DMA_RESERVE_SIZE 0
|
|
|
|
MAIN_STACK 0x200
|
|
PROCESS_STACK 0xA00
|
|
|
|
define HAL_USE_I2C TRUE
|
|
define STM32_I2C_USE_I2C1 TRUE
|
|
|
|
define HAL_UART_MIN_TX_SIZE 256
|
|
define HAL_UART_MIN_RX_SIZE 128
|
|
|
|
define HAL_UART_STACK_SIZE 256
|
|
define STORAGE_THD_WA_SIZE 512
|
|
|
|
|
|
define HAL_I2C_CLEAR_ON_TIMEOUT 0
|
|
|
|
define HAL_DEVICE_THREAD_STACK 768
|
|
|
|
define AP_PARAM_MAX_EMBEDDED_PARAM 0
|
|
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
|
|
# LIS3MDL compass
|
|
COMPASS LIS3MDL SPI:lis3mdl false ROTATION_YAW_270
|
|
|
|
# MS5611 baro
|
|
BARO MS56XX SPI:ms5611
|
|
|
|
define HAL_BARO_ALLOW_INIT_NO_BARO
|
|
|
|
|
|
define HAL_NO_MONITOR_THREAD
|
|
|
|
define HAL_PERIPH_ENABLE_GPS
|
|
define HAL_PERIPH_ENABLE_MAG
|
|
define HAL_PERIPH_ENABLE_BARO
|
|
|
|
# reduce the number of CAN RX Buffer
|
|
define HAL_CAN_RX_QUEUE_SIZE 32
|