ardupilot/APMrover2/defines.h

223 lines
5.3 KiB
C

// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
#ifndef _DEFINES_H
#define _DEFINES_H
// Internal defines, don't edit and expect things to work
// -------------------------------------------------------
#define TRUE 1
#define FALSE 0
#define ToRad(x) radians(x) // *pi/180
#define ToDeg(x) degrees(x) // *180/pi
#define DEBUG 0
#define SERVO_MAX 4500 // This value represents 45 degrees and is just an arbitrary representation of servo max travel.
// failsafe
// ----------------------
#define FAILSAFE_NONE 0
#define FAILSAFE_SHORT 1
#define FAILSAFE_LONG 2
#define FAILSAFE_GCS 3
#define FAILSAFE_SHORT_TIME 1500 // Miliiseconds
#define FAILSAFE_LONG_TIME 20000 // Miliiseconds
// active altitude sensor
// ----------------------
#define SONAR 0
#define BARO 1
#define SONAR_SOURCE_ADC 1
#define SONAR_SOURCE_ANALOG_PIN 2
// CH 7 control
enum ch7_option {
CH7_DO_NOTHING=0,
CH7_SAVE_WP=1
};
#define T6 1000000
#define T7 10000000
// GPS type codes - use the names, not the numbers
#define GPS_PROTOCOL_NONE -1
#define GPS_PROTOCOL_NMEA 0
#define GPS_PROTOCOL_SIRF 1
#define GPS_PROTOCOL_UBLOX 2
#define GPS_PROTOCOL_IMU 3
#define GPS_PROTOCOL_MTK 4
#define GPS_PROTOCOL_HIL 5
#define GPS_PROTOCOL_MTK19 6
#define GPS_PROTOCOL_AUTO 7
#define CH_ROLL CH_1
#define CH_PITCH CH_2
#define CH_THROTTLE CH_3
#define CH_RUDDER CH_4
#define CH_YAW CH_4
#define CH_AIL1 CH_5
#define CH_AIL2 CH_6
// HIL enumerations
#define HIL_MODE_DISABLED 0
#define HIL_MODE_ATTITUDE 1
#define HIL_MODE_SENSORS 2
// Auto Pilot modes
// ----------------
enum mode {
MANUAL=0,
LEARNING=2,
STEERING=3,
AUTO=10,
RTL=11,
GUIDED=15,
INITIALISING=16
};
// Commands - Note that APM now uses a subset of the MAVLink protocol commands. See enum MAV_CMD in the GCS_Mavlink library
#define CMD_BLANK 0 // there is no command stored in the mem location requested
#define NO_COMMAND 0
#define WAIT_COMMAND 255
// Command/Waypoint/Location Options Bitmask
//--------------------
#define MASK_OPTIONS_RELATIVE_ALT (1<<0) // 1 = Relative altitude
//repeating events
#define NO_REPEAT 0
#define CH_5_TOGGLE 1
#define CH_6_TOGGLE 2
#define CH_7_TOGGLE 3
#define CH_8_TOGGLE 4
#define RELAY_TOGGLE 5
#define STOP_REPEAT 10
#define MAV_CMD_CONDITION_YAW 23
// GCS Message ID's
/// NOTE: to ensure we never block on sending MAVLink messages
/// please keep each MSG_ to a single MAVLink message. If need be
/// create new MSG_ IDs for additional messages on the same
/// stream
enum ap_message {
MSG_HEARTBEAT,
MSG_ATTITUDE,
MSG_LOCATION,
MSG_EXTENDED_STATUS1,
MSG_EXTENDED_STATUS2,
MSG_NAV_CONTROLLER_OUTPUT,
MSG_CURRENT_WAYPOINT,
MSG_VFR_HUD,
MSG_RADIO_OUT,
MSG_RADIO_IN,
MSG_RAW_IMU1,
MSG_RAW_IMU3,
MSG_GPS_RAW,
MSG_SERVO_OUT,
MSG_NEXT_WAYPOINT,
MSG_NEXT_PARAM,
MSG_STATUSTEXT,
MSG_AHRS,
MSG_SIMSTATE,
MSG_HWSTATUS,
MSG_RANGEFINDER,
MSG_RETRY_DEFERRED // this must be last
};
enum gcs_severity {
SEVERITY_LOW=1,
SEVERITY_MEDIUM,
SEVERITY_HIGH,
SEVERITY_CRITICAL
};
// Logging parameters
#define LOG_INDEX_MSG 0xF0
#define LOG_ATTITUDE_MSG 0x01
#define LOG_GPS_MSG 0x02
#define LOG_MODE_MSG 0X03
#define LOG_CONTROL_TUNING_MSG 0X04
#define LOG_NAV_TUNING_MSG 0X05
#define LOG_PERFORMANCE_MSG 0X06
#define LOG_IMU_MSG 0x07
#define LOG_CMD_MSG 0x08
#define LOG_CURRENT_MSG 0x09
#define LOG_STARTUP_MSG 0x0A
#define TYPE_AIRSTART_MSG 0x00
#define TYPE_GROUNDSTART_MSG 0x01
#define MAX_NUM_LOGS 100
#define MASK_LOG_ATTITUDE_FAST (1<<0)
#define MASK_LOG_ATTITUDE_MED (1<<1)
#define MASK_LOG_GPS (1<<2)
#define MASK_LOG_PM (1<<3)
#define MASK_LOG_CTUN (1<<4)
#define MASK_LOG_NTUN (1<<5)
#define MASK_LOG_MODE (1<<6)
#define MASK_LOG_IMU (1<<7)
#define MASK_LOG_CMD (1<<8)
#define MASK_LOG_CURRENT (1<<9)
// Waypoint Modes
// ----------------
#define ABS_WP 0
#define REL_WP 1
// Command Queues
// ---------------
#define COMMAND_MUST 0
#define COMMAND_MAY 1
#define COMMAND_NOW 2
// Events
// ------
#define EVENT_WILL_REACH_WAYPOINT 1
#define EVENT_SET_NEW_COMMAND_INDEX 2
#define EVENT_LOADED_WAYPOINT 3
#define EVENT_LOOP 4
// Climb rate calculations
#define ALTITUDE_HISTORY_LENGTH 8 //Number of (time,altitude) points to regress a climb rate from
#define BATTERY_VOLTAGE(x) (x->voltage_average()*g.volt_div_ratio)
#define CURRENT_AMPS(x) (x->voltage_average()-CURR_AMPS_OFFSET)*g.curr_amp_per_volt
#define RELAY_PIN 47
// sonar
#define MAX_SONAR_XL 0
#define MAX_SONAR_LV 1
#define SonarToCm(x) (x*1.26) // Sonar raw value to centimeters
#define AN4 4
#define AN5 5
#define SPEEDFILT 400 // centimeters/second; the speed below which a groundstart will be triggered
// EEPROM addresses
#define EEPROM_MAX_ADDR 4096
// parameters get the first 1KiB of EEPROM, remainder is for waypoints
#define WP_START_BYTE 0x500 // where in memory home WP is stored + all other WP
#define WP_SIZE 15
#define MAX_WAYPOINTS ((EEPROM_MAX_ADDR - WP_START_BYTE) / WP_SIZE) - 1 // - 1 to be safe
// convert a boolean (0 or 1) to a sign for multiplying (0 maps to 1, 1 maps to -1)
#define BOOL_TO_SIGN(bvalue) ((bvalue)?-1:1)
// mark a function as not to be inlined
#define NOINLINE __attribute__((noinline))
#define CONFIG_INS_OILPAN 1
#define CONFIG_INS_MPU6000 2
#define AP_BARO_BMP085 1
#define AP_BARO_MS5611 2
#endif // _DEFINES_H