ardupilot/libraries/AP_HAL_ChibiOS/hwdef/VRBrain-v52/hwdef.dat

171 lines
3.6 KiB
Plaintext

# hw definition file for processing by chibios_hwdef.py
# for VRBRAINv52 hardware
define CONFIG_HAL_BOARD_SUBTYPE HAL_BOARD_SUBTYPE_CHIBIOS_VRBRAIN_V52
# MCU class and specific type
MCU STM32F4xx STM32F407xx
# board ID for firmware load
APJ_BOARD_ID 1152
# crystal frequency
OSCILLATOR_HZ 8000000
# flash size
FLASH_SIZE_KB 1024
# USB setup
USB_VENDOR 0x27AC
USB_PRODUCT 0x1152
USB_STRING_MANUFACTURER "Laser Navigation"
# ChibiOS system timer
STM32_ST_USE_TIMER 5
# only one I2C bus
I2C_ORDER I2C2 I2C1
# order of UARTs (and USB)
SERIAL_ORDER OTG1 USART3 USART2 USART1
STDOUT_SERIAL SD3
STDOUT_BAUDRATE 57600
PA0 BUZZER OUTPUT LOW GPIO(32)
PA1 TIM2_CH2 TIM2 PWM(1) GPIO(50)
PA2 TIM2_CH3 TIM2 PWM(2) GPIO(51)
PA3 TIM2_CH4 TIM2 PWM(3) GPIO(52)
PA4 SDCARD_CS CS
PA5 SPI1_SCK SPI1
PA6 SPI1_MISO SPI1
PA7 SPI1_MOSI SPI1
#PA8
PA9 VBUS INPUT
#P10
PA11 OTG_FS_DM OTG1
PA12 OTG_FS_DP OTG1
PA13 JTMS-SWDIO SWD
PA14 JTCK-SWCLK SWD
#PA15
PB0 TIM3_CH3 TIM3 PWM(5) GPIO(54)
PB1 TIM3_CH4 TIM3 PWM(6) GPIO(55)
#PB2
PB3 LED_EXT3 OUTPUT GPIO(30)
PB4 LED_EXT4 OUTPUT GPIO(31)
PB5 TIM3_CH2 TIM3 PWM(4) GPIO(53)
PB6 USART1_TX USART1
PB7 USART1_RX USART1
PB8 I2C1_SCL I2C1
PB9 I2C1_SDA I2C1
PB10 I2C2_SCL I2C2
PB11 I2C2_SDA I2C2
#PB12
PB13 SPI2_SCK SPI2
PB14 SPI2_MISO SPI2
PB15 SPI2_MOSI SPI2
PC0 BATT_VOLTAGE_SENS ADC1
PC1 BATT_CURRENT_SENS ADC1
#PC2
#PC3
#PC4
PC5 LED_GREEN OUTPUT GPIO(25)
#PC6
PC7 TIM8_CH2 TIM8 RCIN PULLDOWN LOW
PC8 RELAY_1 OUTPUT LOW GPIO(33)
PC9 RELAY_2 OUTPUT LOW GPIO(34)
PC10 SPI3_SCK SPI3
PC11 SPI3_MISO SPI3
PC12 SPI3_MOSI SPI3
#PC13
#PC14
#PC15
#PD0
#PD1
#PD2
#PD3
#PD4
PD5 USART2_TX USART2
PD6 USART2_RX USART2
PD7 SBUS_INV OUTPUT
PD8 USART3_TX USART3
PD9 USART3_RX USART3
#PD10
#PD11
PD12 TIM4_CH1 TIM4 PWM(8) GPIO(57)
PD13 TIM4_CH2 TIM4 PWM(7) GPIO(56)
PD15 LED_RED OUTPUT GPIO(27)
PD14 LED_BLUE OUTPUT GPIO(26)
PE0 BARO_CS CS
#PE1
PE2 LED_EXT1 OUTPUT GPIO(29)
PE3 LED_EXT2 OUTPUT GPIO(28)
PE4 RELAY_3 OUTPUT LOW GPIO(35)
#PE5 TIM9_CH1 TIM9 PWM(13) GPIO(62)
#PE6 TIM9_CH2 TIM9 PWM(14) GPIO(63)
#PE7
#PE8
PE9 TIM1_CH1 TIM1 PWM(9) GPIO(58)
PE10 MPU_CS CS
PE11 TIM1_CH2 TIM1 PWM(10) GPIO(59)
#PE12
PE13 TIM1_CH3 TIM1 PWM(11) GPIO(60)
PE14 TIM1_CH4 TIM1 PWM(12) GPIO(61)
PE15 FRAM_CS CS
# SPI device table. The DEVID values are chosen to match the PX4 port
# of ArduPilot so users don't need to re-do their accel and compass calibrations
# when moving to ChibiOS
SPIDEV ms5611 SPI1 DEVID3 BARO_CS MODE3 20*MHZ 20*MHZ
SPIDEV mpu6000 SPI2 DEVID4 MPU_CS MODE3 2*MHZ 8*MHZ
SPIDEV ramtron SPI3 DEVID10 FRAM_CS MODE3 8*MHZ 8*MHZ
SPIDEV sdcard SPI3 DEVID1 SDCARD_CS MODE0 400*KHZ 25*MHZ
define HAL_CHIBIOS_ARCH_BRAINV52 1
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"
define HAL_STORAGE_SIZE 16384
# enable RAMTROM parameter storage
define HAL_WITH_RAMTRON 1
# enable FAT filesystem
define HAL_OS_FATFS_IO 1
define HAL_GPIO_LED_ON 0
define HAL_GPIO_LED_OFF 1
define HAL_GPIO_A_LED_PIN 25
define HAL_GPIO_B_LED_PIN 26
define HAL_GPIO_C_LED_PIN 27
define EXTERNAL_LED_GPS 28
define EXTERNAL_LED_ARMED 29
define EXTERNAL_LED_MOTOR1 30
define EXTERNAL_LED_MOTOR2 31
define RELAY1_PIN_DEFAULT 33
define RELAY2_PIN_DEFAULT 34
define RELAY3_PIN_DEFAULT 35
define HAL_BUZZER_PIN 32
define HAL_BUZZER_ON 1
define HAL_BUZZER_OFF 0
# battery setup
define HAL_BATT_VOLT_PIN 10
define HAL_BATT_CURR_PIN 11
define HAL_BATT_VOLT_SCALE 10.1
define HAL_BATT_CURR_SCALE 17.0
define STM32_PWM_USE_ADVANCED TRUE
# minimal drivers to reduce flash usage
include ../include/minimal.inc