ardupilot/ArduCopter/afs_copter.cpp

73 lines
2.6 KiB
C++

/*
copter specific AP_AdvancedFailsafe class
*/
#include "Copter.h"
#if ADVANCED_FAILSAFE == ENABLED
// Constructor
AP_AdvancedFailsafe_Copter::AP_AdvancedFailsafe_Copter(AP_Mission &_mission, AP_Baro &_baro, const AP_GPS &_gps, const RCMapper &_rcmap) :
AP_AdvancedFailsafe(_mission, _baro, _gps, _rcmap)
{}
/*
setup radio_out values for all channels to termination values
*/
void AP_AdvancedFailsafe_Copter::terminate_vehicle(void)
{
// stop motors
copter.motors->set_desired_spool_state(AP_Motors::DESIRED_SHUT_DOWN);
copter.motors->output();
// disarm as well
copter.init_disarm_motors();
// and set all aux channels
SRV_Channels::set_output_limit(SRV_Channel::k_heli_rsc, SRV_Channel::SRV_CHANNEL_LIMIT_TRIM);
SRV_Channels::set_output_limit(SRV_Channel::k_heli_tail_rsc, SRV_Channel::SRV_CHANNEL_LIMIT_TRIM);
SRV_Channels::set_output_limit(SRV_Channel::k_engine_run_enable, SRV_Channel::SRV_CHANNEL_LIMIT_TRIM);
SRV_Channels::set_output_limit(SRV_Channel::k_ignition, SRV_Channel::SRV_CHANNEL_LIMIT_TRIM);
SRV_Channels::set_output_limit(SRV_Channel::k_none, SRV_Channel::SRV_CHANNEL_LIMIT_TRIM);
SRV_Channels::set_output_limit(SRV_Channel::k_manual, SRV_Channel::SRV_CHANNEL_LIMIT_TRIM);
SRV_Channels::output_ch_all();
}
void AP_AdvancedFailsafe_Copter::setup_IO_failsafe(void)
{
// setup failsafe for all aux channels
SRV_Channels::set_failsafe_limit(SRV_Channel::k_heli_rsc, SRV_Channel::SRV_CHANNEL_LIMIT_TRIM);
SRV_Channels::set_failsafe_limit(SRV_Channel::k_heli_tail_rsc, SRV_Channel::SRV_CHANNEL_LIMIT_TRIM);
SRV_Channels::set_failsafe_limit(SRV_Channel::k_engine_run_enable, SRV_Channel::SRV_CHANNEL_LIMIT_TRIM);
SRV_Channels::set_failsafe_limit(SRV_Channel::k_ignition, SRV_Channel::SRV_CHANNEL_LIMIT_TRIM);
SRV_Channels::set_failsafe_limit(SRV_Channel::k_none, SRV_Channel::SRV_CHANNEL_LIMIT_TRIM);
SRV_Channels::set_failsafe_limit(SRV_Channel::k_manual, SRV_Channel::SRV_CHANNEL_LIMIT_TRIM);
#if FRAME_CONFIG != HELI_FRAME
// setup AP_Motors outputs for failsafe
uint16_t mask = copter.motors->get_motor_mask();
hal.rcout->set_failsafe_pwm(mask, copter.motors->get_pwm_output_min());
#endif
}
/*
return an AFS_MODE for current control mode
*/
AP_AdvancedFailsafe::control_mode AP_AdvancedFailsafe_Copter::afs_mode(void)
{
switch (copter.control_mode) {
case AUTO:
case GUIDED:
case RTL:
case LAND:
return AP_AdvancedFailsafe::AFS_AUTO;
default:
break;
}
return AP_AdvancedFailsafe::AFS_STABILIZED;
}
#endif // ADVANCED_FAILSAFE