mirror of https://github.com/ArduPilot/ardupilot
350 lines
8.6 KiB
Plaintext
350 lines
8.6 KiB
Plaintext
# hw definition file for processing by chibios_hwdef.py
|
|
|
|
# MCU class and specific type
|
|
MCU STM32H7xx STM32H743xx
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 16000000
|
|
|
|
# USB setup
|
|
USB_VENDOR 0x3162 # ONLY FOR USE BY Holybro
|
|
USB_PRODUCT 0x004B
|
|
USB_STRING_MANUFACTURER "Holybro"
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 139
|
|
|
|
FLASH_SIZE_KB 2048
|
|
|
|
# with 2M flash we can afford to optimize for speed
|
|
env OPTIMIZE -O2
|
|
|
|
# bootloader takes first sector
|
|
FLASH_RESERVE_START_KB 128
|
|
|
|
|
|
# order of UARTs (and USB)
|
|
SERIAL_ORDER OTG1 USART2 USART3 USART1 UART4 USART6 UART7 OTG2
|
|
|
|
# default the 2nd interface to MAVLink2 until MissionPlanner updates drivers
|
|
define HAL_OTG2_PROTOCOL SerialProtocol_MAVLink2
|
|
|
|
define HAL_STORAGE_SIZE 32768
|
|
|
|
define CONFIG_HAL_BOARD_SUBTYPE HAL_BOARD_SUBTYPE_CHIBIOS_FMUV5
|
|
define HAL_CHIBIOS_ARCH_FMUV5 1
|
|
define BOARD_TYPE_DEFAULT 24
|
|
|
|
# now we define the pins that USB is connected on
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
# these are the pins for SWD debugging with a STlinkv2 or black-magic probe
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# SPI1 - internal sensors
|
|
PG11 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PD7 SPI1_MOSI SPI1
|
|
|
|
# SPI2 - FRAM
|
|
PI1 SPI2_SCK SPI2
|
|
PI2 SPI2_MISO SPI2
|
|
PI3 SPI2_MOSI SPI2
|
|
|
|
# SPI4 - sensors2
|
|
PE2 SPI4_SCK SPI4
|
|
PE13 SPI4_MISO SPI4
|
|
PE6 SPI4_MOSI SPI4
|
|
|
|
# SPI5 - external1
|
|
PF7 SPI5_SCK SPI5
|
|
PF8 SPI5_MISO SPI5
|
|
PF9 SPI5_MOSI SPI5
|
|
|
|
# SPI6 - external2
|
|
PG13 SPI6_SCK SPI6
|
|
PG12 SPI6_MISO SPI6
|
|
PB5 SPI6_MOSI SPI6
|
|
|
|
# sensor CS
|
|
PF10 MS5611_CS CS
|
|
PF2 ICM20689_CS CS SPEED_VERYLOW
|
|
PF3 ICM20602_CS CS SPEED_VERYLOW
|
|
PF4 BMI055_G_CS CS
|
|
PG10 BMI055_A_CS CS
|
|
PF5 FRAM_CS CS SPEED_VERYLOW
|
|
|
|
# external CS pins, SPI5 connector
|
|
PI4 EXT1_CS1 CS
|
|
PI10 EXT1_CS2 CS
|
|
|
|
# external CS pins, SPI6 connector
|
|
PI6 EXT2_CS1 CS
|
|
PI7 EXT2_CS2 CS
|
|
PI8 EXT2_CS3 CS
|
|
|
|
|
|
# I2C buses
|
|
|
|
# I2C1 is on GPS port
|
|
PB8 I2C1_SCL I2C1
|
|
PB9 I2C1_SDA I2C1
|
|
|
|
# I2C on telem4 connector
|
|
PF1 I2C2_SCL I2C2
|
|
PF0 I2C2_SDA I2C2
|
|
|
|
# I2C for onboard mag
|
|
PH7 I2C3_SCL I2C3
|
|
PH8 I2C3_SDA I2C3
|
|
|
|
# I2C4 is on BDMA on DMAMUX2, connected to I2CA connector
|
|
PF14 I2C4_SCL I2C4
|
|
PF15 I2C4_SDA I2C4
|
|
|
|
# order of I2C buses
|
|
I2C_ORDER I2C3 I2C1 I2C2 I2C4
|
|
|
|
define HAL_I2C_INTERNAL_MASK 1
|
|
|
|
# enable pins
|
|
PE3 VDD_3V3_SENSORS_EN OUTPUT LOW
|
|
|
|
# start peripheral power off, then enable after init
|
|
# this prevents a problem with radios that use RTS for
|
|
# bootloader hold
|
|
PF12 nVDD_5V_HIPOWER_EN OUTPUT HIGH
|
|
PG4 nVDD_5V_PERIPH_EN OUTPUT HIGH
|
|
|
|
PG5 VDD_5V_RC_EN OUTPUT HIGH
|
|
PG6 VDD_5V_WIFI_EN OUTPUT HIGH
|
|
PG7 VDD_3V3_SD_CARD_EN OUTPUT HIGH
|
|
|
|
# drdy pins
|
|
PE7 DRDY8_NC INPUT
|
|
PB4 DRDY1_ICM20689 INPUT
|
|
PB14 DRDY2_BMI055_GYRO INPUT
|
|
PB15 DRDY3_BMI055_ACC INPUT
|
|
PC5 DRDY4_ICM20602 INPUT
|
|
PC13 DRDY5_BMI055_GYRO INPUT
|
|
PD10 DRDY6_BMI055_ACC INPUT
|
|
PD15 DRDY7_EXTERNAL1 INPUT
|
|
|
|
# UARTs
|
|
|
|
# USART2 is telem1
|
|
PD6 USART2_RX USART2
|
|
PD5 USART2_TX USART2
|
|
PD3 USART2_CTS USART2
|
|
PD4 USART2_RTS USART2
|
|
|
|
# USART1 is GPS1
|
|
PB7 USART1_RX USART1 NODMA
|
|
PB6 USART1_TX USART1 NODMA
|
|
|
|
# USART3 is telem2
|
|
PD9 USART3_RX USART3
|
|
PD8 USART3_TX USART3
|
|
PD11 USART3_CTS USART3
|
|
PD12 USART3_RTS USART3
|
|
|
|
# UART4 GPS2
|
|
PD0 UART4_RX UART4 NODMA
|
|
PD1 UART4_TX UART4 NODMA
|
|
|
|
# USART6 is telem3
|
|
PG9 USART6_RX USART6 NODMA
|
|
PG14 USART6_TX USART6
|
|
PG15 USART6_CTS USART6
|
|
PG8 USART6_RTS USART6
|
|
|
|
# UART7 is debug
|
|
PF6 UART7_RX UART7 NODMA
|
|
PE8 UART7_TX UART7 NODMA
|
|
|
|
# UART8 is for IOMCU
|
|
PE0 UART8_RX UART8
|
|
PE1 UART8_TX UART8
|
|
|
|
# UART for IOMCU
|
|
IOMCU_UART UART8
|
|
|
|
# PWM AUX channels
|
|
PE14 TIM1_CH4 TIM1 PWM(1) GPIO(50)
|
|
PA10 TIM1_CH3 TIM1 PWM(2) GPIO(51)
|
|
PE11 TIM1_CH2 TIM1 PWM(3) GPIO(52)
|
|
PE9 TIM1_CH1 TIM1 PWM(4) GPIO(53)
|
|
PD13 TIM4_CH2 TIM4 PWM(5) GPIO(54)
|
|
PD14 TIM4_CH3 TIM4 PWM(6) GPIO(55)
|
|
# we need to disable DMA on the last 2 FMU channels
|
|
# as timer 12 doesn't have a TIMn_UP DMA option
|
|
PH6 TIM12_CH1 TIM12 PWM(7) GPIO(56) NODMA
|
|
PH9 TIM12_CH2 TIM12 PWM(8) GPIO(57) NODMA
|
|
|
|
# PWM output for buzzer
|
|
PE5 TIM15_CH1 TIM15 GPIO(77) ALARM
|
|
|
|
# analog in
|
|
PA0 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
PA1 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
PA2 BATT2_VOLTAGE_SENS ADC1 SCALE(1)
|
|
PA3 BATT2_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
PC4 SPARE1_ADC1 ADC1 SCALE(1)
|
|
PA4 SPARE2_ADC1 ADC1 SCALE(1)
|
|
|
|
PB0 RSSI_IN ADC1 SCALE(1)
|
|
|
|
#PC3 HW_REV_SENS ADC1 SCALE(1)
|
|
#PC2 HW_VER_SENS ADC1 SCALE(1)
|
|
|
|
PC0 VDD_5V_SENS ADC1 SCALE(2)
|
|
PC1 SCALED_V3V3 ADC1 SCALE(2)
|
|
|
|
# voltage divider 1/(16.9/(33+16.9))
|
|
define HAL_IOMCU_VSERVO_SCALAR 1 / (16.9 / (33 + 16.9))
|
|
|
|
# CAN bus
|
|
PI9 CAN1_RX CAN1
|
|
PH13 CAN1_TX CAN1
|
|
|
|
PB12 CAN2_RX CAN2
|
|
PB13 CAN2_TX CAN2
|
|
|
|
PH2 GPIO_CAN1_SILENT OUTPUT PUSHPULL SPEED_LOW LOW GPIO(70)
|
|
PH3 GPIO_CAN2_SILENT OUTPUT PUSHPULL SPEED_LOW LOW GPIO(71)
|
|
PH4 GPIO_CAN3_SILENT OUTPUT PUSHPULL SPEED_LOW LOW GPIO(72)
|
|
|
|
# GPIOs
|
|
PA7 HEATER_EN OUTPUT LOW GPIO(80)
|
|
define HAL_HEATER_GPIO_PIN 80
|
|
|
|
define HAL_HAVE_IMU_HEATER 1
|
|
define HAL_IMU_TEMP_DEFAULT 45
|
|
|
|
# SPI temperature sensor
|
|
PH5 TSENSE_CS CS
|
|
|
|
PG1 VDD_BRICK_nVALID INPUT PULLUP
|
|
PG2 VDD_BRICK2_nVALID INPUT PULLUP
|
|
PA9 VBUS INPUT
|
|
PF13 VDD_5V_HIPOWER_nOC INPUT PULLUP
|
|
PE15 VDD_5V_PERIPH_nOC INPUT PULLUP
|
|
PB10 nSPI5_RESET_EXTERNAL1 OUTPUT HIGH
|
|
|
|
# capture pins
|
|
PA5 FMU_CAP1 INPUT GPIO(58)
|
|
PB3 FMU_CAP2 INPUT GPIO(59)
|
|
PB11 FMU_CAP3 INPUT GPIO(60)
|
|
PI0 FMU_SPARE_4 INPUT GPIO(61)
|
|
|
|
# SPI devices
|
|
SPIDEV ms5611 SPI4 DEVID1 MS5611_CS MODE3 20*MHZ 20*MHZ
|
|
SPIDEV icm20689 SPI1 DEVID1 ICM20689_CS MODE3 2*MHZ 8*MHZ
|
|
SPIDEV icm20602 SPI1 DEVID2 ICM20602_CS MODE3 2*MHZ 8*MHZ
|
|
SPIDEV bmi055_g SPI1 DEVID3 BMI055_G_CS MODE3 10*MHZ 10*MHZ
|
|
SPIDEV bmi055_a SPI1 DEVID4 BMI055_A_CS MODE3 10*MHZ 10*MHZ
|
|
SPIDEV ramtron SPI2 DEVID1 FRAM_CS MODE3 8*MHZ 8*MHZ
|
|
SPIDEV icm20602_2 SPI1 DEVID4 BMI055_G_CS MODE3 2*MHZ 8*MHZ
|
|
|
|
# SPI5 external connections
|
|
SPIDEV external1m0 SPI5 DEVID1 EXT1_CS1 MODE0 2*MHZ 2*MHZ
|
|
SPIDEV external1m1 SPI5 DEVID1 EXT1_CS1 MODE1 2*MHZ 2*MHZ
|
|
SPIDEV external1m2 SPI5 DEVID1 EXT1_CS1 MODE2 2*MHZ 2*MHZ
|
|
SPIDEV external1m3 SPI5 DEVID1 EXT1_CS1 MODE3 2*MHZ 2*MHZ
|
|
SPIDEV external2m0 SPI5 DEVID2 EXT1_CS2 MODE0 2*MHZ 2*MHZ
|
|
SPIDEV external2m1 SPI5 DEVID2 EXT1_CS2 MODE1 2*MHZ 2*MHZ
|
|
SPIDEV external2m2 SPI5 DEVID2 EXT1_CS2 MODE2 2*MHZ 2*MHZ
|
|
SPIDEV external2m3 SPI5 DEVID2 EXT1_CS2 MODE3 2*MHZ 2*MHZ
|
|
|
|
# SPI6 external connections
|
|
SPIDEV external3m0 SPI6 DEVID1 EXT2_CS1 MODE0 2*MHZ 2*MHZ
|
|
SPIDEV external3m1 SPI6 DEVID1 EXT2_CS1 MODE1 2*MHZ 2*MHZ
|
|
SPIDEV external3m2 SPI6 DEVID1 EXT2_CS1 MODE2 2*MHZ 2*MHZ
|
|
SPIDEV external3m3 SPI6 DEVID1 EXT2_CS1 MODE3 2*MHZ 2*MHZ
|
|
SPIDEV external4m0 SPI6 DEVID2 EXT2_CS2 MODE0 2*MHZ 2*MHZ
|
|
SPIDEV external4m1 SPI6 DEVID2 EXT2_CS2 MODE1 2*MHZ 2*MHZ
|
|
SPIDEV external4m2 SPI6 DEVID2 EXT2_CS2 MODE2 2*MHZ 2*MHZ
|
|
SPIDEV external4m3 SPI6 DEVID2 EXT2_CS2 MODE3 2*MHZ 2*MHZ
|
|
SPIDEV external5m0 SPI6 DEVID2 EXT2_CS3 MODE0 2*MHZ 2*MHZ
|
|
SPIDEV external5m1 SPI6 DEVID2 EXT2_CS3 MODE1 2*MHZ 2*MHZ
|
|
SPIDEV external5m2 SPI6 DEVID2 EXT2_CS3 MODE2 2*MHZ 2*MHZ
|
|
SPIDEV external5m3 SPI6 DEVID2 EXT2_CS3 MODE3 2*MHZ 2*MHZ
|
|
|
|
# Two IMUs
|
|
IMU Invensense SPI:icm20689 ROTATION_NONE
|
|
IMU BMI088 SPI:bmi055_a SPI:bmi055_g ROTATION_ROLL_180_YAW_90
|
|
# These are here for compatibility with pre-release boards
|
|
IMU BMI055 SPI:bmi055_a SPI:bmi055_g ROTATION_ROLL_180_YAW_90
|
|
# alternative 20602 IMU for some variants
|
|
IMU Invensense SPI:icm20602_2 ROTATION_NONE
|
|
|
|
define HAL_DEFAULT_INS_FAST_SAMPLE 7
|
|
|
|
# microSD support (disabled for now)
|
|
PC8 SDMMC1_D0 SDMMC1
|
|
PC9 SDMMC1_D1 SDMMC1
|
|
PC10 SDMMC1_D2 SDMMC1
|
|
PC11 SDMMC1_D3 SDMMC1
|
|
PC12 SDMMC1_CK SDMMC1
|
|
PD2 SDMMC1_CMD SDMMC1
|
|
|
|
# red LED marked as B/E
|
|
PB1 LED_RED OUTPUT GPIO(90)
|
|
|
|
# green LED marked as PWR. We leave this solid on, but allow
|
|
# for it to be controlled as a relay if needed
|
|
PC6 LED_GREEN OUTPUT GPIO(91) LOW
|
|
|
|
# blue LED marked as ACT
|
|
PC7 LED_BLUE OUTPUT GPIO(92) HIGH
|
|
|
|
# setup for BoardLED2
|
|
define HAL_GPIO_A_LED_PIN 90
|
|
define HAL_GPIO_B_LED_PIN 92
|
|
define HAL_GPIO_LED_ON 0
|
|
|
|
# enable RAMTROM parameter storage
|
|
define HAL_STORAGE_SIZE 32768
|
|
define HAL_WITH_RAMTRON 1
|
|
|
|
# allow to have have a dedicated safety switch pin
|
|
define HAL_HAVE_SAFETY_SWITCH 1
|
|
|
|
# one baro
|
|
BARO MS56XX SPI:ms5611
|
|
|
|
define HAL_COMPASS_DEFAULT HAL_COMPASS_NONE
|
|
define HAL_COMPASS_AUTO_ROT_DEFAULT 2
|
|
|
|
# enable FAT filesystem support (needs a microSD defined via SDMMC)
|
|
define HAL_OS_FATFS_IO 1
|
|
|
|
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
|
|
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"
|
|
|
|
ROMFS io_firmware.bin Tools/IO_Firmware/iofirmware_lowpolh.bin
|
|
|
|
# don't share IOMCU DMA
|
|
DMA_NOSHARE UART8* SPI1* TIM*UP*
|
|
|
|
DMA_PRIORITY UART8* ADC* SPI1*
|
|
|
|
# battery setup
|
|
define HAL_BATT_MONITOR_DEFAULT 4
|
|
define HAL_BATT_VOLT_PIN 16
|
|
define HAL_BATT_CURR_PIN 17
|
|
define HAL_BATT2_VOLT_PIN 14
|
|
define HAL_BATT2_CURR_PIN 15
|
|
define HAL_BATT_VOLT_SCALE 18.182
|
|
define HAL_BATT_CURR_SCALE 36.364
|
|
|
|
|
|
# there is an issue with DMA on SPI which needs to be solved
|
|
# before we enable it
|
|
#define HAL_SPI_USE_POLLED
|
|
|