mirror of https://github.com/ArduPilot/ardupilot
108 lines
2.4 KiB
Plaintext
108 lines
2.4 KiB
Plaintext
# MCU class and specific type
|
|
MCU STM32L431 STM32L431xx
|
|
|
|
# bootloader starts firmware at 36k + 4k (STORAGE_FLASH)
|
|
FLASH_RESERVE_START_KB 40
|
|
FLASH_SIZE_KB 256
|
|
|
|
# store parameters in pages 18 and 19
|
|
STORAGE_FLASH_PAGE 18
|
|
define HAL_STORAGE_SIZE 800
|
|
|
|
# ChibiOS system timer
|
|
STM32_ST_USE_TIMER 15
|
|
define CH_CFG_ST_RESOLUTION 16
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 1109
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 8000000
|
|
env AP_PERIPH 1
|
|
STDOUT_SERIAL SD1
|
|
STDOUT_BAUDRATE 57600
|
|
|
|
define HAL_NO_GPIO_IRQ
|
|
define SERIAL_BUFFERS_SIZE 512
|
|
define PORT_INT_REQUIRED_STACK 64
|
|
define DMA_RESERVE_SIZE 0
|
|
|
|
# MAIN_STACK is stack for ISR handlers
|
|
MAIN_STACK 0x300
|
|
|
|
# PROCESS_STACK controls stack for main thread
|
|
PROCESS_STACK 0xA00
|
|
|
|
# we setup a small defaults.parm
|
|
define AP_PARAM_MAX_EMBEDDED_PARAM 512
|
|
|
|
# blue LED0 marked as ACT
|
|
PB3 LED OUTPUT HIGH
|
|
define HAL_LED_ON 1
|
|
|
|
# debugger support
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# I2C bus
|
|
I2C_ORDER I2C2
|
|
PB13 I2C2_SCL I2C2
|
|
PB14 I2C2_SDA I2C2
|
|
define HAL_I2C_CLEAR_ON_TIMEOUT 0
|
|
define HAL_I2C_INTERNAL_MASK 1
|
|
|
|
# CAN bus
|
|
CAN_ORDER 1
|
|
PB8 CAN1_RX CAN1
|
|
PB9 CAN1_TX CAN1
|
|
# PC13 GPIO_CAN1_SILENT OUTPUT PUSHPULL SPEED_LOW LOW
|
|
define HAL_CAN_POOL_SIZE 12000
|
|
|
|
# UARTs
|
|
SERIAL_ORDER USART1 EMPTY EMPTY
|
|
|
|
# USART1
|
|
PB6 USART1_TX USART1 SPEED_HIGH
|
|
PB7 USART1_RX USART1 SPEED_HIGH
|
|
|
|
# allow for reboot command for faster development
|
|
define HAL_PERIPH_LISTEN_FOR_SERIAL_UART_REBOOT_CMD_PORT 0
|
|
|
|
# keep ROMFS uncompressed as we don't have enough RAM
|
|
# to uncompress the bootloader at runtime
|
|
env ROMFS_UNCOMPRESSED True
|
|
|
|
# enable GPS and compass
|
|
define HAL_PERIPH_ENABLE_GPS
|
|
define GPS_MAX_RATE_MS 200
|
|
define GPS_MAX_RECEIVERS 1
|
|
define GPS_MAX_INSTANCES 1
|
|
define HAL_PERIPH_GPS_PORT_DEFAULT 0
|
|
|
|
# allow for F9P GPS modules with moving baseline
|
|
define GPS_MOVING_BASELINE 1
|
|
define HAL_PERIPH_ENABLE_MAG
|
|
define HAL_COMPASS_MAX_SENSORS 1
|
|
|
|
# QMC5883L for different board varients
|
|
COMPASS QMC5883L I2C:0:0xd false ROTATION_YAW_180
|
|
|
|
# no ADC pins
|
|
define HAL_USE_ADC FALSE
|
|
|
|
# disable unnecessary threads
|
|
define HAL_NO_TIMER_THREAD
|
|
|
|
# enable LED
|
|
define HAL_PERIPH_ENABLE_RC_OUT
|
|
define HAL_PERIPH_ENABLE_NOTIFY
|
|
|
|
#GPIO LED
|
|
define AP_NOTIFY_GPIO_LED_RGB_ENABLED 1
|
|
PB2 LED_RED OUTPUT OPENDRAIN HIGH GPIO(0)
|
|
PB4 LED_GREEN OUTPUT OPENDRAIN LOW GPIO(1)
|
|
PB5 LED_BLUE OUTPUT OPENDRAIN LOW GPIO(2)
|
|
define AP_NOTIFY_GPIO_LED_RGB_RED_PIN 0
|
|
define AP_NOTIFY_GPIO_LED_RGB_GREEN_PIN 1
|
|
define AP_NOTIFY_GPIO_LED_RGB_BLUE_PIN 2
|