ardupilot/ArduPlane/commands.pde

131 lines
3.7 KiB
Plaintext

// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
/*
* logic for dealing with the current command in the mission and home location
*/
/*
* set_next_WP - sets the target location the vehicle should fly to
*/
static void set_next_WP(const struct Location &loc)
{
if (auto_state.next_wp_no_crosstrack) {
// we should not try to cross-track for this waypoint
prev_WP_loc = current_loc;
// use cross-track for the next waypoint
auto_state.next_wp_no_crosstrack = false;
auto_state.no_crosstrack = true;
} else {
// copy the current WP into the OldWP slot
prev_WP_loc = next_WP_loc;
auto_state.no_crosstrack = false;
}
// Load the next_WP slot
// ---------------------
next_WP_loc = loc;
// if lat and lon is zero, then use current lat/lon
// this allows a mission to contain a "loiter on the spot"
// command
if (next_WP_loc.lat == 0 && next_WP_loc.lng == 0) {
next_WP_loc.lat = current_loc.lat;
next_WP_loc.lng = current_loc.lng;
// additionally treat zero altitude as current altitude
if (next_WP_loc.alt == 0) {
next_WP_loc.alt = current_loc.alt;
next_WP_loc.flags.relative_alt = false;
next_WP_loc.flags.terrain_alt = false;
}
}
// convert relative alt to absolute alt
if (next_WP_loc.flags.relative_alt) {
next_WP_loc.flags.relative_alt = false;
next_WP_loc.alt += home.alt;
}
// are we already past the waypoint? This happens when we jump
// waypoints, and it can cause us to skip a waypoint. If we are
// past the waypoint when we start on a leg, then use the current
// location as the previous waypoint, to prevent immediately
// considering the waypoint complete
if (location_passed_point(current_loc, prev_WP_loc, next_WP_loc)) {
gcs_send_text_P(SEVERITY_LOW, PSTR("Resetting prev_WP"));
prev_WP_loc = current_loc;
}
// used to control FBW and limit the rate of climb
// -----------------------------------------------
set_target_altitude_location(next_WP_loc);
// zero out our loiter vals to watch for missed waypoints
loiter_angle_reset();
setup_glide_slope();
setup_turn_angle();
loiter_angle_reset();
}
static void set_guided_WP(void)
{
if (g.loiter_radius < 0) {
loiter.direction = -1;
} else {
loiter.direction = 1;
}
// copy the current location into the OldWP slot
// ---------------------------------------
prev_WP_loc = current_loc;
// Load the next_WP slot
// ---------------------
next_WP_loc = guided_WP_loc;
// used to control FBW and limit the rate of climb
// -----------------------------------------------
set_target_altitude_current();
update_flight_stage();
setup_glide_slope();
setup_turn_angle();
loiter_angle_reset();
}
// run this at setup on the ground
// -------------------------------
static void init_home()
{
gcs_send_text_P(SEVERITY_LOW, PSTR("init home"));
ahrs.set_home(gps.location());
home_is_set = true;
gcs_send_text_fmt(PSTR("gps alt: %lu"), (unsigned long)home.alt);
// Save Home to EEPROM
mission.write_home_to_storage();
// Save prev loc
// -------------
next_WP_loc = prev_WP_loc = home;
// Load home for a default guided_WP
// -------------
guided_WP_loc = home;
guided_WP_loc.alt += g.RTL_altitude_cm;
}
/*
update home location from GPS
this is called as long as we have 3D lock and the arming switch is
not pushed
*/
static void update_home()
{
ahrs.set_home(gps.location());
barometer.update_calibration();
}