mirror of https://github.com/ArduPilot/ardupilot
377 lines
15 KiB
C++
377 lines
15 KiB
C++
/*
|
|
This program is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
This program is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
#include <AP_HAL/AP_HAL.h>
|
|
#include <AP_Vehicle/AP_Vehicle_Type.h>
|
|
|
|
#include <AP_Math/AP_Math.h>
|
|
#include <GCS_MAVLink/GCS.h>
|
|
#include <SRV_Channel/SRV_Channel.h>
|
|
|
|
#include "AP_MotorsTri.h"
|
|
|
|
extern const AP_HAL::HAL& hal;
|
|
|
|
// init
|
|
void AP_MotorsTri::init(motor_frame_class frame_class, motor_frame_type frame_type)
|
|
{
|
|
add_motor_num(AP_MOTORS_MOT_1);
|
|
add_motor_num(AP_MOTORS_MOT_2);
|
|
add_motor_num(AP_MOTORS_MOT_4);
|
|
|
|
// set update rate for the 3 motors (but not the servo on channel 7)
|
|
set_update_rate(_speed_hz);
|
|
|
|
// set the motor_enabled flag so that the ESCs can be calibrated like other frame types
|
|
motor_enabled[AP_MOTORS_MOT_1] = true;
|
|
motor_enabled[AP_MOTORS_MOT_2] = true;
|
|
motor_enabled[AP_MOTORS_MOT_4] = true;
|
|
|
|
// allow mapping of motor7
|
|
add_motor_num(AP_MOTORS_CH_TRI_YAW);
|
|
|
|
// Check for tail servo
|
|
_have_tail_servo = SRV_Channels::function_assigned(SRV_Channel::k_motor7);
|
|
|
|
SRV_Channels::set_angle(SRV_Channels::get_motor_function(AP_MOTORS_CH_TRI_YAW), _yaw_servo_angle_max_deg*100);
|
|
|
|
// check for reverse tricopter
|
|
if (frame_type == MOTOR_FRAME_TYPE_PLUSREV) {
|
|
_pitch_reversed = true;
|
|
}
|
|
|
|
_mav_type = MAV_TYPE_TRICOPTER;
|
|
|
|
// record successful initialisation if what we setup was the desired frame_class
|
|
set_initialised_ok(frame_class == MOTOR_FRAME_TRI);
|
|
}
|
|
|
|
// set frame class (i.e. quad, hexa, heli) and type (i.e. x, plus)
|
|
void AP_MotorsTri::set_frame_class_and_type(motor_frame_class frame_class, motor_frame_type frame_type)
|
|
{
|
|
// check for reverse tricopter
|
|
if (frame_type == MOTOR_FRAME_TYPE_PLUSREV) {
|
|
_pitch_reversed = true;
|
|
} else {
|
|
_pitch_reversed = false;
|
|
}
|
|
|
|
set_initialised_ok((frame_class == MOTOR_FRAME_TRI) && SRV_Channels::function_assigned(SRV_Channel::k_motor7));
|
|
}
|
|
|
|
// set update rate to motors - a value in hertz
|
|
void AP_MotorsTri::set_update_rate(uint16_t speed_hz)
|
|
{
|
|
// record requested speed
|
|
_speed_hz = speed_hz;
|
|
|
|
// set update rate for the 3 motors (but not the servo on channel 7)
|
|
uint32_t mask =
|
|
1U << AP_MOTORS_MOT_1 |
|
|
1U << AP_MOTORS_MOT_2 |
|
|
1U << AP_MOTORS_MOT_4;
|
|
rc_set_freq(mask, _speed_hz);
|
|
}
|
|
|
|
void AP_MotorsTri::output_to_motors()
|
|
{
|
|
switch (_spool_state) {
|
|
case SpoolState::SHUT_DOWN:
|
|
// sends minimum values out to the motors
|
|
rc_write(AP_MOTORS_MOT_1, output_to_pwm(0));
|
|
rc_write(AP_MOTORS_MOT_2, output_to_pwm(0));
|
|
rc_write(AP_MOTORS_MOT_4, output_to_pwm(0));
|
|
rc_write_angle(AP_MOTORS_CH_TRI_YAW, 0);
|
|
break;
|
|
case SpoolState::GROUND_IDLE:
|
|
// sends output to motors when armed but not flying
|
|
set_actuator_with_slew(_actuator[1], actuator_spin_up_to_ground_idle());
|
|
set_actuator_with_slew(_actuator[2], actuator_spin_up_to_ground_idle());
|
|
set_actuator_with_slew(_actuator[4], actuator_spin_up_to_ground_idle());
|
|
rc_write(AP_MOTORS_MOT_1, output_to_pwm(_actuator[1]));
|
|
rc_write(AP_MOTORS_MOT_2, output_to_pwm(_actuator[2]));
|
|
rc_write(AP_MOTORS_MOT_4, output_to_pwm(_actuator[4]));
|
|
rc_write_angle(AP_MOTORS_CH_TRI_YAW, 0);
|
|
break;
|
|
case SpoolState::SPOOLING_UP:
|
|
case SpoolState::THROTTLE_UNLIMITED:
|
|
case SpoolState::SPOOLING_DOWN:
|
|
// set motor output based on thrust requests
|
|
set_actuator_with_slew(_actuator[1], thr_lin.thrust_to_actuator(_thrust_right));
|
|
set_actuator_with_slew(_actuator[2], thr_lin.thrust_to_actuator(_thrust_left));
|
|
set_actuator_with_slew(_actuator[4], thr_lin.thrust_to_actuator(_thrust_rear));
|
|
rc_write(AP_MOTORS_MOT_1, output_to_pwm(_actuator[1]));
|
|
rc_write(AP_MOTORS_MOT_2, output_to_pwm(_actuator[2]));
|
|
rc_write(AP_MOTORS_MOT_4, output_to_pwm(_actuator[4]));
|
|
rc_write_angle(AP_MOTORS_CH_TRI_YAW, degrees(_pivot_angle)*100);
|
|
break;
|
|
}
|
|
}
|
|
|
|
// get_motor_mask - returns a bitmask of which outputs are being used for motors or servos (1 means being used)
|
|
// this can be used to ensure other pwm outputs (i.e. for servos) do not conflict
|
|
uint32_t AP_MotorsTri::get_motor_mask()
|
|
{
|
|
// tri copter uses channels 1,2,4 and 7
|
|
uint32_t motor_mask = (1U << AP_MOTORS_MOT_1) |
|
|
(1U << AP_MOTORS_MOT_2) |
|
|
(1U << AP_MOTORS_MOT_4);
|
|
uint32_t mask = motor_mask_to_srv_channel_mask(motor_mask);
|
|
|
|
// add parent's mask
|
|
mask |= AP_MotorsMulticopter::get_motor_mask();
|
|
|
|
return mask;
|
|
}
|
|
|
|
// output_armed - sends commands to the motors
|
|
// includes new scaling stability patch
|
|
void AP_MotorsTri::output_armed_stabilizing()
|
|
{
|
|
float roll_thrust; // roll thrust input value, +/- 1.0
|
|
float pitch_thrust; // pitch thrust input value, +/- 1.0
|
|
float yaw_thrust; // yaw thrust input value, +/- 1.0
|
|
float throttle_thrust; // throttle thrust input value, 0.0 - 1.0
|
|
float throttle_avg_max; // throttle thrust average maximum value, 0.0 - 1.0
|
|
float throttle_thrust_best_rpy; // throttle providing maximum roll, pitch and yaw range without climbing
|
|
float rpy_scale = 1.0f; // this is used to scale the roll, pitch and yaw to fit within the motor limits
|
|
float rpy_low = 0.0f; // lowest motor value
|
|
float rpy_high = 0.0f; // highest motor value
|
|
float thr_adj; // the difference between the pilot's desired throttle and throttle_thrust_best_rpy
|
|
|
|
SRV_Channels::set_angle(SRV_Channels::get_motor_function(AP_MOTORS_CH_TRI_YAW), _yaw_servo_angle_max_deg*100);
|
|
|
|
// sanity check YAW_SV_ANGLE parameter value to avoid divide by zero
|
|
_yaw_servo_angle_max_deg.set(constrain_float(_yaw_servo_angle_max_deg, AP_MOTORS_TRI_SERVO_RANGE_DEG_MIN, AP_MOTORS_TRI_SERVO_RANGE_DEG_MAX));
|
|
|
|
// apply voltage and air pressure compensation
|
|
const float compensation_gain = thr_lin.get_compensation_gain();
|
|
roll_thrust = (_roll_in + _roll_in_ff) * compensation_gain;
|
|
pitch_thrust = (_pitch_in + _pitch_in_ff) * compensation_gain;
|
|
yaw_thrust = (_yaw_in + _yaw_in_ff) * compensation_gain * sinf(radians(_yaw_servo_angle_max_deg)); // we scale this so a thrust request of 1.0f will ask for full servo deflection at full rear throttle
|
|
throttle_thrust = get_throttle() * compensation_gain;
|
|
throttle_avg_max = _throttle_avg_max * compensation_gain;
|
|
|
|
// check for reversed pitch
|
|
if (_pitch_reversed) {
|
|
pitch_thrust *= -1.0f;
|
|
}
|
|
|
|
// VTOL plane may not have tail servo
|
|
if (!_have_tail_servo) {
|
|
_pivot_angle = 0.0;
|
|
} else {
|
|
// calculate angle of yaw pivot
|
|
_pivot_angle = safe_asin(yaw_thrust);
|
|
if (fabsf(_pivot_angle) > radians(_yaw_servo_angle_max_deg)) {
|
|
limit.yaw = true;
|
|
_pivot_angle = constrain_float(_pivot_angle, -radians(_yaw_servo_angle_max_deg), radians(_yaw_servo_angle_max_deg));
|
|
}
|
|
}
|
|
|
|
float pivot_thrust_max = cosf(_pivot_angle);
|
|
float thrust_max = 1.0f;
|
|
|
|
// sanity check throttle is above zero and below current limited throttle
|
|
if (throttle_thrust <= 0.0f) {
|
|
throttle_thrust = 0.0f;
|
|
limit.throttle_lower = true;
|
|
}
|
|
if (throttle_thrust >= _throttle_thrust_max) {
|
|
throttle_thrust = _throttle_thrust_max;
|
|
limit.throttle_upper = true;
|
|
}
|
|
|
|
throttle_avg_max = constrain_float(throttle_avg_max, throttle_thrust, _throttle_thrust_max);
|
|
|
|
// The following mix may be offer less coupling between axis but needs testing
|
|
//_thrust_right = roll_thrust * -0.5f + pitch_thrust * 1.0f;
|
|
//_thrust_left = roll_thrust * 0.5f + pitch_thrust * 1.0f;
|
|
//_thrust_rear = 0;
|
|
|
|
_thrust_right = roll_thrust * -0.5f + pitch_thrust * 0.5f;
|
|
_thrust_left = roll_thrust * 0.5f + pitch_thrust * 0.5f;
|
|
_thrust_rear = pitch_thrust * -0.5f;
|
|
|
|
// calculate roll and pitch for each motor
|
|
// set rpy_low and rpy_high to the lowest and highest values of the motors
|
|
|
|
// record lowest roll pitch command
|
|
rpy_low = MIN(_thrust_right, _thrust_left);
|
|
rpy_high = MAX(_thrust_right, _thrust_left);
|
|
if (rpy_low > _thrust_rear) {
|
|
rpy_low = _thrust_rear;
|
|
}
|
|
// check to see if the rear motor will reach maximum thrust before the front two motors
|
|
if ((1.0f - rpy_high) > (pivot_thrust_max - _thrust_rear)) {
|
|
thrust_max = pivot_thrust_max;
|
|
rpy_high = _thrust_rear;
|
|
}
|
|
|
|
// calculate throttle that gives most possible room for yaw (range 1000 ~ 2000) which is the lower of:
|
|
// 1. 0.5f - (rpy_low+rpy_high)/2.0 - this would give the maximum possible room margin above the highest motor and below the lowest
|
|
// 2. the higher of:
|
|
// a) the pilot's throttle input
|
|
// b) the point _throttle_rpy_mix between the pilot's input throttle and hover-throttle
|
|
// Situation #2 ensure we never increase the throttle above hover throttle unless the pilot has commanded this.
|
|
// Situation #2b allows us to raise the throttle above what the pilot commanded but not so far that it would actually cause the copter to rise.
|
|
// We will choose #1 (the best throttle for yaw control) if that means reducing throttle to the motors (i.e. we favor reducing throttle *because* it provides better yaw control)
|
|
// We will choose #2 (a mix of pilot and hover throttle) only when the throttle is quite low. We favor reducing throttle instead of better yaw control because the pilot has commanded it
|
|
|
|
// check everything fits
|
|
throttle_thrust_best_rpy = MIN(0.5f * thrust_max - (rpy_low + rpy_high) / 2.0, throttle_avg_max);
|
|
if (is_zero(rpy_low)) {
|
|
rpy_scale = 1.0f;
|
|
} else {
|
|
rpy_scale = constrain_float(-throttle_thrust_best_rpy / rpy_low, 0.0f, 1.0f);
|
|
}
|
|
|
|
// calculate how close the motors can come to the desired throttle
|
|
thr_adj = throttle_thrust - throttle_thrust_best_rpy;
|
|
if (rpy_scale < 1.0f) {
|
|
// Full range is being used by roll, pitch, and yaw.
|
|
limit.roll = true;
|
|
limit.pitch = true;
|
|
if (thr_adj > 0.0f) {
|
|
limit.throttle_upper = true;
|
|
}
|
|
thr_adj = 0.0f;
|
|
} else {
|
|
if (thr_adj < -(throttle_thrust_best_rpy + rpy_low)) {
|
|
// Throttle can't be reduced to desired value
|
|
thr_adj = -(throttle_thrust_best_rpy + rpy_low);
|
|
} else if (thr_adj > thrust_max - (throttle_thrust_best_rpy + rpy_high)) {
|
|
// Throttle can't be increased to desired value
|
|
thr_adj = thrust_max - (throttle_thrust_best_rpy + rpy_high);
|
|
limit.throttle_upper = true;
|
|
}
|
|
}
|
|
|
|
// determine throttle thrust for harmonic notch
|
|
const float throttle_thrust_best_plus_adj = throttle_thrust_best_rpy + thr_adj;
|
|
// compensation_gain can never be zero
|
|
_throttle_out = throttle_thrust_best_plus_adj / compensation_gain;
|
|
|
|
// add scaled roll, pitch, constrained yaw and throttle for each motor
|
|
_thrust_right = throttle_thrust_best_plus_adj + rpy_scale * _thrust_right;
|
|
_thrust_left = throttle_thrust_best_plus_adj + rpy_scale * _thrust_left;
|
|
_thrust_rear = throttle_thrust_best_plus_adj + rpy_scale * _thrust_rear;
|
|
|
|
// scale pivot thrust to account for pivot angle
|
|
// we should not need to check for divide by zero as _pivot_angle is constrained to the 5deg ~ 80 deg range
|
|
_thrust_rear = _thrust_rear / cosf(_pivot_angle);
|
|
|
|
// constrain all outputs to 0.0f to 1.0f
|
|
// test code should be run with these lines commented out as they should not do anything
|
|
_thrust_right = constrain_float(_thrust_right, 0.0f, 1.0f);
|
|
_thrust_left = constrain_float(_thrust_left, 0.0f, 1.0f);
|
|
_thrust_rear = constrain_float(_thrust_rear, 0.0f, 1.0f);
|
|
}
|
|
|
|
// output_test_seq - spin a motor at the pwm value specified
|
|
// motor_seq is the motor's sequence number from 1 to the number of motors on the frame
|
|
// pwm value is an actual pwm value that will be output, normally in the range of 1000 ~ 2000
|
|
void AP_MotorsTri::_output_test_seq(uint8_t motor_seq, int16_t pwm)
|
|
{
|
|
// output to motors and servos
|
|
switch (motor_seq) {
|
|
case 1:
|
|
// front right motor
|
|
rc_write(AP_MOTORS_MOT_1, pwm);
|
|
break;
|
|
case 2:
|
|
// back motor
|
|
rc_write(AP_MOTORS_MOT_4, pwm);
|
|
break;
|
|
case 3:
|
|
// back servo
|
|
rc_write(AP_MOTORS_CH_TRI_YAW, pwm);
|
|
break;
|
|
case 4:
|
|
// front left motor
|
|
rc_write(AP_MOTORS_MOT_2, pwm);
|
|
break;
|
|
default:
|
|
// do nothing
|
|
break;
|
|
}
|
|
}
|
|
|
|
/*
|
|
call vehicle supplied thrust compensation if set. This allows for
|
|
vehicle specific thrust compensation for motor arrangements such as
|
|
the forward motors tilting
|
|
*/
|
|
void AP_MotorsTri::thrust_compensation(void)
|
|
{
|
|
if (_thrust_compensation_callback) {
|
|
// convert 3 thrust values into an array indexed by motor number
|
|
float thrust[4] { _thrust_right, _thrust_left, 0, _thrust_rear };
|
|
|
|
// apply vehicle supplied compensation function
|
|
_thrust_compensation_callback(thrust, 4);
|
|
|
|
// extract compensated thrust values
|
|
_thrust_right = thrust[0];
|
|
_thrust_left = thrust[1];
|
|
_thrust_rear = thrust[3];
|
|
}
|
|
}
|
|
|
|
/*
|
|
override tricopter tail servo output in output_motor_mask
|
|
*/
|
|
void AP_MotorsTri::output_motor_mask(float thrust, uint16_t mask, float rudder_dt)
|
|
{
|
|
// normal multicopter output
|
|
AP_MotorsMulticopter::output_motor_mask(thrust, mask, rudder_dt);
|
|
|
|
// and override yaw servo
|
|
rc_write_angle(AP_MOTORS_CH_TRI_YAW, 0);
|
|
}
|
|
|
|
float AP_MotorsTri::get_roll_factor(uint8_t i)
|
|
{
|
|
float ret = 0.0f;
|
|
|
|
switch (i) {
|
|
// right motor
|
|
case AP_MOTORS_MOT_1:
|
|
ret = -1.0f;
|
|
break;
|
|
// left motor
|
|
case AP_MOTORS_MOT_2:
|
|
ret = 1.0f;
|
|
break;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
// Run arming checks
|
|
bool AP_MotorsTri::arming_checks(size_t buflen, char *buffer) const
|
|
{
|
|
#if !APM_BUILD_TYPE(APM_BUILD_ArduPlane) // Tilt Rotors do not need a yaw servo
|
|
// Check for yaw servo
|
|
if (!_have_tail_servo) {
|
|
hal.util->snprintf(buffer, buflen, "no SERVOx_FUNCTION set to Motor7 for tail servo");
|
|
return false;
|
|
}
|
|
#endif
|
|
|
|
// run base class checks
|
|
return AP_MotorsMulticopter::arming_checks(buflen, buffer);
|
|
}
|