mirror of https://github.com/ArduPilot/ardupilot
148 lines
3.0 KiB
Plaintext
148 lines
3.0 KiB
Plaintext
# hw definition file for processing by chibios_hwdef.py
|
|
# for H755 - H755 is almost identical to H757, so utilizing its STM32H757xx.py file
|
|
|
|
AUTOBUILD_TARGETS None
|
|
|
|
# MCU class and specific type
|
|
MCU STM32H7xx STM32H757xx
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
STM32_ST_USE_TIMER 5
|
|
|
|
define CORE_CM7
|
|
define SMPS_PWR
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 139
|
|
|
|
# the nucleo seems to have trouble with flashing the last sector?
|
|
FLASH_SIZE_KB 2048
|
|
|
|
FLASH_BOOTLOADER_LOAD_KB 256
|
|
FLASH_RESERVE_START_KB 256
|
|
|
|
define HAL_STORAGE_SIZE 32768
|
|
STORAGE_FLASH_PAGE 14
|
|
|
|
# order of UARTs (and USB)
|
|
SERIAL_ORDER OTG1 USART2 UART7 USART1 UART4 UART5
|
|
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# order of UARTs and suggested uses
|
|
# USART2 TELEM1
|
|
# UART7 TELEM2
|
|
# USART1 GPS
|
|
# UART4 RCIN/OUT Telem
|
|
# UART5 DEBUG
|
|
|
|
# telem1 USART2
|
|
PD3 USART2_CTS USART2
|
|
PD4 USART2_RTS USART2
|
|
PD5 USART2_TX USART2
|
|
PD6 USART2_RX USART2
|
|
|
|
# telem2 UART7
|
|
PF9 UART7_CTS UART7
|
|
PF8 UART7_RTS UART7
|
|
PF7 UART7_TX UART7
|
|
PF6 UART7_RX UART7
|
|
|
|
# GPS USART1
|
|
PB7 USART1_RX USART1
|
|
PB6 USART1_TX USART1
|
|
|
|
# RCIN/OUT UART4
|
|
PB9 UART4_TX UART4
|
|
PB8 UART4_RX UART4
|
|
|
|
# debug uart5
|
|
PB13 UART5_TX UART5
|
|
PB12 UART5_RX UART5
|
|
|
|
# Now setup the pins for the microSD card, if available.
|
|
PC8 SDMMC1_D0 SDMMC1
|
|
PC9 SDMMC1_D1 SDMMC1
|
|
PC10 SDMMC1_D2 SDMMC1
|
|
PC11 SDMMC1_D3 SDMMC1
|
|
PC12 SDMMC1_CK SDMMC1
|
|
PD2 SDMMC1_CMD SDMMC1
|
|
|
|
# CAN Busses
|
|
PD0 CAN1_RX CAN1
|
|
PD1 CAN1_TX CAN1
|
|
|
|
# PWM Output
|
|
PB1 TIM8_CH3N TIM8 PWM(1) GPIO(50)
|
|
PA0 TIM2_CH1 TIM2 PWM(2) GPIO(51)
|
|
PE9 TIM1_CH1 TIM1 PWM(3) GPIO(52)
|
|
PA2 TIM2_CH3 TIM2 PWM(4) GPIO(53)
|
|
PA3 TIM2_CH4 TIM2 PWM(5) GPIO(54)
|
|
PD12 TIM4_CH1 TIM4 PWM(6) GPIO(55)
|
|
PD13 TIM4_CH2 TIM4 PWM(7) GPIO(56)
|
|
PD14 TIM4_CH3 TIM4 PWM(8) GPIO(57)
|
|
PD15 TIM4_CH4 TIM4 PWM(9) GPIO(58)
|
|
PE5 TIM15_CH1 TIM15 PWM(10) GPIO(59)
|
|
PE6 TIM15_CH2 TIM15 PWM(11) GPIO(60)
|
|
PA8 TIM1_CH1 TIM1 PWM(12) GPIO(61) # for WS2812 LED
|
|
|
|
define HAL_SPI_CHECK_CLOCK_FREQ
|
|
|
|
# sensor CS
|
|
PC7 MPU_CS CS
|
|
|
|
# status LEDs
|
|
define HAL_LED_ON 0
|
|
PB0 LED OUTPUT HIGH GPIO(0) #Green
|
|
PE1 LED1 OUTPUT HIGH GPIO(2) #Yellow
|
|
PB14 LED2 OUTPUT HIGH GPIO(1) #Red
|
|
define HAL_GPIO_A_LED_PIN 0
|
|
define HAL_GPIO_B_LED_PIN 1
|
|
define HAL_GPIO_C_LED_PIN 2
|
|
define HAL_GPIO_LED_OFF 1
|
|
define HAL_GPIO_LED_ON 0
|
|
|
|
# I2C
|
|
I2C_ORDER I2C2
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
PB10 I2C2_SCL I2C2
|
|
PB11 I2C2_SDA I2C2
|
|
|
|
# Enable FAT filesystem support (needs a microSD defined via SDMMC).
|
|
define HAL_OS_FATFS_IO 1
|
|
|
|
# barometers
|
|
BARO BMP388 I2C:0:0x77
|
|
|
|
# SPI1
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
# SPI3
|
|
PB3 SPI3_SCK SPI3
|
|
PB4 SPI3_MISO SPI3
|
|
PB5 SPI3_MOSI SPI3
|
|
|
|
# SPI devices
|
|
SPIDEV icm20948 SPI3 DEVID1 MPU_CS MODE3 4*MHZ 8*MHZ
|
|
|
|
# analog in
|
|
PC0 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
PC3 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
# probe for an invensense IMU
|
|
IMU Invensensev2 SPI:icm20948 ROTATION_YAW_270
|
|
|
|
# compass as part of ICM20948 on newer cubes
|
|
COMPASS AK09916:probe_ICM20948 0 ROTATION_ROLL_180_YAW_90
|
|
|
|
# bootloader embedding / bootloader flashing not available
|
|
define AP_BOOTLOADER_FLASHING_ENABLED 0
|