mirror of https://github.com/ArduPilot/ardupilot
146 lines
2.8 KiB
Plaintext
146 lines
2.8 KiB
Plaintext
# hw definition file for processing by chibios_pins.py
|
|
|
|
# MCU class and specific type
|
|
MCU STM32F4xx STM32F405xx
|
|
|
|
# bootloader starts firmware at 60+ 4k
|
|
FLASH_RESERVE_START_KB 64
|
|
|
|
#MCU F405 store parameters in pages 2 and 3
|
|
STORAGE_FLASH_PAGE 2
|
|
define HAL_STORAGE_SIZE 15360
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 1064
|
|
|
|
# setup build for a peripheral firmware
|
|
env AP_PERIPH 1
|
|
|
|
# crystal frequency set to 0 to use internal clock
|
|
OSCILLATOR_HZ 0
|
|
|
|
#MCU F405 Flash 1024
|
|
FLASH_SIZE_KB 1024
|
|
|
|
# order of UARTs
|
|
SERIAL_ORDER OTG1 USART2 USART3 UART4
|
|
|
|
define HAL_CAN_POOL_SIZE 6000
|
|
|
|
#STDOUT_SERIAL SD1
|
|
#STDOUT_BAUDRATE 57600
|
|
|
|
|
|
# PWM outputs
|
|
PA9 TIM1_CH2 TIM1 PWM(1) GPIO(50)
|
|
PA8 TIM1_CH1 TIM1 PWM(2) GPIO(51)
|
|
|
|
# USART2, ESC telem
|
|
PA2 USART2_TX USART2 SPEED_HIGH NODMA
|
|
PA3 USART2_RX USART2 SPEED_HIGH NODMA
|
|
|
|
# USART3
|
|
PC10 USART3_TX USART3 SPEED_HIGH NODMA
|
|
PC11 USART3_RX USART3 SPEED_HIGH NODMA
|
|
|
|
# UART4
|
|
PA0 UART4_TX UART4 SPEED_HIGH NODMA
|
|
PA1 UART4_RX UART4 SPEED_HIGH NODMA
|
|
|
|
# USB
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
# LED, active low
|
|
PA15 LED OUTPUT HIGH GPIO(1)
|
|
|
|
# spi2
|
|
PB10 SPI2_SCK SPI2
|
|
PB14 SPI2_MISO SPI2
|
|
PB15 SPI2_MOSI SPI2
|
|
|
|
# CS pins
|
|
PC8 BMI088_A_CS CS
|
|
PC9 BMI088_G_CS CS
|
|
|
|
SPIDEV bmi088_g SPI2 DEVID1 BMI088_G_CS MODE3 10*MHZ 10*MHZ
|
|
SPIDEV bmi088_a SPI2 DEVID2 BMI088_A_CS MODE3 10*MHZ 10*MHZ
|
|
|
|
# one I2C bus
|
|
PB6 I2C1_SCL I2C1
|
|
PB7 I2C1_SDA I2C1
|
|
|
|
I2C_ORDER I2C1
|
|
|
|
# allow for reboot command for faster development
|
|
define HAL_PERIPH_LISTEN_FOR_SERIAL_UART_REBOOT_CMD_PORT 0
|
|
|
|
# debugger support
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
define HAL_NO_GPIO_IRQ
|
|
define SERIAL_BUFFERS_SIZE 512
|
|
|
|
define DMA_RESERVE_SIZE 2048
|
|
|
|
# stack for fast interrupts
|
|
define PORT_INT_REQUIRED_STACK 64
|
|
|
|
# MAIN_STACK is stack for ISR handlers
|
|
MAIN_STACK 0x300
|
|
|
|
# PROCESS_STACK controls stack for main thread
|
|
PROCESS_STACK 0xA00
|
|
|
|
define HAL_DISABLE_LOOP_DELAY
|
|
|
|
# enable CAN support
|
|
PB8 CAN1_RX CAN1
|
|
PB9 CAN1_TX CAN1
|
|
|
|
# ADC inputs
|
|
define HAL_USE_ADC TRUE
|
|
define STM32_ADC_USE_ADC1 TRUE
|
|
|
|
PA5 VSENSE1 ADC1 SCALE(1)
|
|
PA6 VSENSE2 ADC1 SCALE(1)
|
|
PB0 VSENSE3 ADC1 SCALE(1)
|
|
PB1 VSENSE4 ADC1 SCALE(1)
|
|
|
|
define AP_STATS_ENABLED 1
|
|
|
|
define HAL_NO_GCS
|
|
define HAL_NO_MONITOR_THREAD
|
|
|
|
define AP_PARAM_MAX_EMBEDDED_PARAM 512
|
|
|
|
define HAL_PERIPH_ENABLE_MAG
|
|
define HAL_PERIPH_ENABLE_BARO
|
|
define HAL_PERIPH_ENABLE_RC_OUT
|
|
|
|
# enable ESC control
|
|
define HAL_SUPPORT_RCOUT_SERIAL 1
|
|
define HAL_WITH_ESC_TELEM 1
|
|
|
|
# enable GPS
|
|
define HAL_PERIPH_ENABLE_GPS
|
|
define HAL_PERIPH_GPS_PORT_DEFAULT 2
|
|
#define HAL_PERIPH_ENABLE_NOTIFY
|
|
#define HAL_PERIPH_ENABLE_NCP5623_LED_WITHOUT_NOTIFY
|
|
|
|
# default ADSB off by setting 0 baudrate
|
|
define HAL_PERIPH_ENABLE_ADSB
|
|
define HAL_PERIPH_ADSB_PORT_DEFAULT 3
|
|
define HAL_PERIPH_ADSB_BAUD_DEFAULT 57600
|
|
|
|
BARO MS56XX I2C:0:0x76
|
|
COMPASS MMC5XX3 I2C:0:0x30 false ROTATION_NONE
|
|
|
|
define AP_COMPASS_QMC5883P_ENABLED 1
|
|
COMPASS QMC5883P I2C:0:0x2C false ROTATION_YAW_180
|
|
|
|
|
|
|
|
|