mirror of https://github.com/ArduPilot/ardupilot
1056 lines
36 KiB
C
1056 lines
36 KiB
C
// -------------------------------------------------------------
|
|
// ArduPPM (PPM Encoder) V2.3.17
|
|
// -------------------------------------------------------------
|
|
// Improved servo to ppm for ArduPilot MEGA v1.x (ATmega328p),
|
|
// PhoneDrone and APM2.x (ATmega32u2)
|
|
|
|
// By: John Arne Birkeland - 2012
|
|
// APM v1.x adaptation and "difficult" receiver testing by Olivier ADLER
|
|
// -------------------------------------------------------------
|
|
|
|
|
|
// -------------------------------------------------------------
|
|
// ARDUPPM OPERATIONAL DESCRIPTION
|
|
// -------------------------------------------------------------
|
|
|
|
// APM 2.x LED STATUS:
|
|
// -------------------
|
|
// RX - OFF = No input signal detected
|
|
// RX - SLOW TOGGLE = Input signal OK
|
|
// RX - FAST TOGGLE = Invalid input signal(s) detected
|
|
// RX - ON = Input signal(s) lost during flight and fail-safe activated
|
|
// TX - OFF = PPM output disabled
|
|
// TX - FAST TOGGLE = PPM output enabled
|
|
// TX - SLOW TOGGLE = PPM pass-trough mode
|
|
|
|
// SERVO INPUT (PWM) MODE:
|
|
// -----------------------
|
|
// - PPM output will not be enabled unless a input signal has been detected and verified
|
|
// - Verified inputs are lost during operaton (lose servo wire or receiver malfunction):
|
|
// + The last known value of the lost input channel is keept for ~1 second
|
|
// + If the lost input channel is not restored within ~1 second, it will be set to the default fail-safe value
|
|
// - Lost channel signal is restored:
|
|
// + Normal channel operation is restored using the valid input signal
|
|
|
|
// PPM PASS-THROUGH MODE (signal pin 2&3 shorted):
|
|
// -----------------------------------------------
|
|
// - Any input level changes on pin 1 will be passed directly to the PPM output (PPM pass-trough)
|
|
// + If no input level changes are detected or if the input signals stop, there will be no PPM output
|
|
|
|
// Changelog:
|
|
|
|
// 01-08-2011
|
|
// V2.2.3 - Changed back to BLOCKING interrupts.
|
|
// Assembly PPM compare interrupt can be switch back to non-blocking, but not recommended.
|
|
// V2.2.3 - Implemented 0.5us cut filter to remove servo input capture jitter.
|
|
|
|
// 04-08-2011
|
|
// V2.2.4 - Implemented PPM passtrough function.
|
|
// Shorting channel 2&3 enabled ppm passtrough on channel 1.
|
|
|
|
// 04-08-2011
|
|
// V2.2.5 - Implemented simple average filter to smooth servo input capture jitter.
|
|
// Takes fewer clocks to execute and has better performance then cut filter.
|
|
|
|
// 05-08-2011
|
|
// V2.2.51 - Minor bug fixes.
|
|
|
|
// 06-08-2011
|
|
// V2.2.6 - PPM passtrough failsafe implemented.
|
|
// The PPM generator will be activated and output failsafe values while ppm passtrough signal is missing.
|
|
|
|
// 01-09-2011
|
|
// V2.2.61 - Temporary MUX pin always high patch for APM beta board
|
|
|
|
// 22-09-2011
|
|
// V2.2.62 - ATmegaXXU2 USB connection status pin (PC2) for APM UART MUX selection (removed temporary high patch)
|
|
// - Removed assembly optimized PPM generator (not usable for production release)
|
|
|
|
// 23-09-2011
|
|
// V2.2.63 - Average filter disabled
|
|
|
|
// 24-09-2011
|
|
// V2.2.64 - Added distincts Power on / Failsafe PPM values
|
|
// - Changed CH5 (mode selection) PPM Power on and Failsafe values to 1555 (Flight mode 4)
|
|
// - Added brownout detection : Failsafe values are copied after a brownout reset instead of power on values
|
|
|
|
// 25-09-2011
|
|
// V2.2.65 - Implemented PPM output delay until input signal is detected (PWM and PPM pass-trough mode)
|
|
// - Changed brownout detection and FailSafe handling to work with XXU2 chips
|
|
// - Minor variable and define naming changes to enhance readability
|
|
|
|
// 15-03-2012
|
|
// V2.2.66 - Added APM2 (ATmega32U2) support for using TX and RX status leds to indicate PWM and PPM traffic
|
|
// - <RX>: <OFF> = no pwm input detected, <TOGGLE> = speed of toggle indicate how many channel are active, <ON> = input lost (failsafe)
|
|
// - <TX>: <OFF> = ppm output not started, <FAST TOGGLE> = normal PWM->PPM output or PPM passtrough failsafe, <SLOW TOGGLE> = PPM passtrough
|
|
|
|
// 03-06-2012
|
|
// V2.2.67 - Implemented detection and failsafe (throttle = 900us) for missing throttle signal.
|
|
|
|
// 04-06-2012
|
|
// V2.2.68 - Fixed possible logic flaw in throttle failsafe reset if _JITTER_FILTER_ is enabled
|
|
|
|
// 02-11-2012
|
|
// V2.2.69 - Added PPM output positive polarity - mainly for standalone PPM encoder board use
|
|
|
|
// 03-11-2012
|
|
// V2.3.0 - Implemented single channel fail-safe detection for all inputs
|
|
|
|
// 16-11-2012
|
|
// V2.3.1 - Improved watchdog timer reset, so that only valid input signals will prevent the watchdog timer from triggering
|
|
|
|
// 22-11-2012
|
|
// V2.3.11 - Very experimental test forcing throttle fail-safe (RTL) on single channel loss. !DO NOT RELEASE TO PUBLIC!
|
|
// - Test for active input channels during init
|
|
|
|
// 23-11-2012 !VERY EXPERIMENTAL!
|
|
// V2.3.11 - Nested interrupt PWM output interrupt (PPM generator) for greatly improved jitter performance
|
|
// - Active input channel test during init removed
|
|
// - Implemented dynamic testing of active input channels
|
|
|
|
// 23-12-2012
|
|
// V2.3.12 - New improved fail-safe detection and handeling for single or multible signal loss and receiver malfuntion
|
|
// - Improved LED status for APM 2.x
|
|
// - Improved jitter performance (PPM output using nested interrupts)
|
|
|
|
// 30-11-2012
|
|
// V2.3.13pre - Internal dev only pre-release
|
|
// - Improved active channel detection requering 100 valid pulses before channel is marked active
|
|
// - Removed forced throttle fail-safe after channel loss
|
|
// - Changed fail-safe values to 800us, this will be used by APM code to detect channel loss and decide fail safe actions
|
|
|
|
// 16-12-2012
|
|
// V2.3.13 - Official release
|
|
// - Fail-safe vales changed back to normal fail-safe values. Use until APM code knows how to handle lost channel signal (800us)
|
|
|
|
// 10-01-2013
|
|
// V2.3.14pre - Internal test release
|
|
// - If one or more or all channel(s) are disconnected, throttle is set to fail-safe low (RTL)
|
|
// - If the misssing channel(s) are regained, throttle control is regained
|
|
|
|
// 11-01-2013
|
|
// V2.3.14 - temporary release for ArduCopter 2.9
|
|
// - fail-safe throttle low can be set with a define
|
|
// - recovery from error condition can also be set with a define
|
|
|
|
// 13-01-2013
|
|
// V2.3.15 - very small bug fix: speedup
|
|
|
|
// 27-02-2013
|
|
// V2.3.16 - if channel 1, 2 or 4 is disconnected: set it to center (1500us)
|
|
// - if channel 3 (throttle) is disconnected: set it to low (900us)
|
|
// - if channel 5-8 are disconnected: set it to last value
|
|
// - permanent LED error condition indication is only triggered when throttle is set low (or all channels are disconnected)
|
|
|
|
// 16-12-2013
|
|
// V2.3.17 - Disabled fail-safe output when signal is missing in PPM pass-trough (PPMSUM) mode (feature depreciated by addition of missing signal detection in APM code)
|
|
// - ppm_encoder_init() will now make sure PPM output always starts with fail-safe (900us) value on throttle after a brown-out reset
|
|
|
|
// -------------------------------------------------------------
|
|
#pragma once
|
|
|
|
#include <avr/io.h>
|
|
|
|
// -------------------------------------------------------------
|
|
|
|
#include <avr/interrupt.h>
|
|
#include <avr/wdt.h>
|
|
#include <util/delay.h>
|
|
|
|
|
|
// -------------------------------------------------------------
|
|
// SERVO INPUT FILTERS AND PARAMETERS
|
|
// -------------------------------------------------------------
|
|
// Using both filters is not recommended and may reduce servo input resolution
|
|
|
|
//#define _AVERAGE_FILTER_ // Average filter to smooth servo input capture jitter
|
|
#define _JITTER_FILTER_ 2 // Cut filter to remove servo input capture jitter (1 unit = 0.5us)
|
|
#define _INPUT_ERROR_TRIGGER_ 100 // Number of invalid input signals allowed before triggering alarm
|
|
// -------------------------------------------------------------
|
|
|
|
#ifndef F_CPU
|
|
#define F_CPU 16000000UL
|
|
#endif
|
|
|
|
#ifndef true
|
|
#define true 1
|
|
#endif
|
|
|
|
#ifndef false
|
|
#define false 0
|
|
#endif
|
|
|
|
#ifndef bool
|
|
#define bool _Bool
|
|
#endif
|
|
|
|
// Version stamp for firmware hex file ( decode hex file using <avr-objdump -s file.hex> and look for "ArduPPM" string )
|
|
const char ver[15] = "ArduPPMv2.3.17";
|
|
|
|
// -------------------------------------------------------------
|
|
// INPUT MODE
|
|
// -------------------------------------------------------------
|
|
|
|
#define JUMPER_SELECT_MODE 0 // Default - PPM passtrough mode selected if channel 2&3 shorted. Normal servo input (pwm) if not shorted.
|
|
#define SERVO_PWM_MODE 1 // Normal 8 channel servo (pwm) input
|
|
#define PPM_PASSTROUGH_MODE 2 // PPM signal passtrough on channel 1
|
|
#define JETI_MODE 3 // Reserved
|
|
#define SPEKTRUM_MODE 4 // Reserved for Spektrum satelitte on channel 1
|
|
|
|
// Servo input mode (jumper (default), pwm, ppm, jeti or spektrum)
|
|
volatile uint8_t servo_input_mode = JUMPER_SELECT_MODE;
|
|
|
|
// -------------------------------------------------------------
|
|
// FAILSAFE MODE
|
|
// -------------------------------------------------------------
|
|
|
|
//#define _APM_FAILSAFE_ // Used to spesify APM 800us channel loss fail safe values, remove to use normal fail safe values (stand alone encoder board)
|
|
|
|
//#define _THROTTLE_LOW_FAILSAFE_INDICATION //if set, throttle is set to low when a single channel is lost
|
|
//#define _THROTTLE_LOW_RECOVERY_POSSIBLE //if set, throttle low recovers from being low when the single channel comes back, only makes sense together with _THROTTLE_LOW_FAILSAFE_INDICATION
|
|
|
|
#define _PPM_PASSTROUGH_MODE_DISABLE_FAILSAFE_ // Disable fail-safe PPM generator and watchdog timer in ppm pass-trough (PPMSUM) mode
|
|
|
|
#if defined _THROTTLE_LOW_RECOVERY_POSSIBLE && !defined _THROTTLE_LOW_FAILSAFE_INDICATION
|
|
#error failsafe recovery is only possible with throttle_low_failsafe_indication defined as well
|
|
#endif
|
|
|
|
// -------------------------------------------------------------
|
|
// SERVO LIMIT VALUES
|
|
// -------------------------------------------------------------
|
|
|
|
// Number of Timer1 ticks in one microsecond
|
|
#define ONE_US F_CPU / 8 / 1000 / 1000
|
|
|
|
// 400us PPM pre pulse
|
|
#define PPM_PRE_PULSE ONE_US * 400
|
|
|
|
// Servo minimum position
|
|
#define PPM_SERVO_MIN ONE_US * 900 - PPM_PRE_PULSE
|
|
|
|
// Servo center position
|
|
#define PPM_SERVO_CENTER ONE_US * 1500 - PPM_PRE_PULSE
|
|
|
|
// Servo maximum position
|
|
#define PPM_SERVO_MAX ONE_US * 2100 - PPM_PRE_PULSE
|
|
|
|
// Throttle default at power on
|
|
#define PPM_THROTTLE_DEFAULT ONE_US * 1100 - PPM_PRE_PULSE
|
|
|
|
// Throttle during failsafe
|
|
#define PPM_THROTTLE_FAILSAFE ONE_US * 900 - PPM_PRE_PULSE
|
|
|
|
// Channel loss failsafe
|
|
#define PPM_CHANNEL_LOSS ONE_US * 800 - PPM_PRE_PULSE
|
|
|
|
// CH5 power on values (mode selection channel)
|
|
#define PPM_CH5_MODE_4 ONE_US * 1555 - PPM_PRE_PULSE
|
|
|
|
// -------------------------------------------------------------
|
|
// PPM OUTPUT SETTINGS
|
|
// -------------------------------------------------------------
|
|
// #define _POSITIVE_PPM_FRAME_ // Switch to positive pulse PPM
|
|
// (the actual timing is encoded in the length of the low between two pulses)
|
|
|
|
// Number of servo input channels
|
|
#define SERVO_CHANNELS 8
|
|
|
|
// PPM period 18.5ms - 26.5ms (54hz - 37Hz)
|
|
#define PPM_PERIOD ONE_US * ( 22500 - ( 8 * 1500 ) )
|
|
|
|
// Size of ppm[..] data array ( servo channels * 2 + 2)
|
|
#define PPM_ARRAY_MAX 18
|
|
|
|
#ifdef _APM_FAILSAFE_
|
|
// -------------------------------------------------------------
|
|
// APM FAILSAFE VALUES
|
|
// -------------------------------------------------------------
|
|
volatile uint16_t failsafe_ppm[ PPM_ARRAY_MAX ] =
|
|
{
|
|
PPM_PRE_PULSE,
|
|
PPM_CHANNEL_LOSS, // Channel 1
|
|
PPM_PRE_PULSE,
|
|
PPM_CHANNEL_LOSS, // Channel 2
|
|
PPM_PRE_PULSE,
|
|
PPM_CHANNEL_LOSS, // Channel 3 (throttle)
|
|
PPM_PRE_PULSE,
|
|
PPM_CHANNEL_LOSS, // Channel 4
|
|
PPM_PRE_PULSE,
|
|
PPM_CHANNEL_LOSS, // Channel 5
|
|
PPM_PRE_PULSE,
|
|
PPM_CHANNEL_LOSS, // Channel 6
|
|
PPM_PRE_PULSE,
|
|
PPM_CHANNEL_LOSS, // Channel 7
|
|
PPM_PRE_PULSE,
|
|
PPM_CHANNEL_LOSS, // Channel 8
|
|
PPM_PRE_PULSE,
|
|
PPM_PERIOD
|
|
};
|
|
#else
|
|
// -------------------------------------------------------------
|
|
// SERVO FAILSAFE VALUES
|
|
// -------------------------------------------------------------
|
|
volatile uint16_t failsafe_ppm[ PPM_ARRAY_MAX ] =
|
|
{
|
|
PPM_PRE_PULSE,
|
|
PPM_SERVO_CENTER, // Channel 1
|
|
PPM_PRE_PULSE,
|
|
PPM_SERVO_CENTER, // Channel 2
|
|
PPM_PRE_PULSE,
|
|
PPM_THROTTLE_FAILSAFE, // Channel 3 (throttle)
|
|
PPM_PRE_PULSE,
|
|
PPM_SERVO_CENTER, // Channel 4
|
|
PPM_PRE_PULSE,
|
|
PPM_CH5_MODE_4, // Channel 5
|
|
PPM_PRE_PULSE,
|
|
PPM_SERVO_CENTER, // Channel 6
|
|
PPM_PRE_PULSE,
|
|
PPM_SERVO_CENTER, // Channel 7
|
|
PPM_PRE_PULSE,
|
|
PPM_SERVO_CENTER, // Channel 8
|
|
PPM_PRE_PULSE,
|
|
PPM_PERIOD
|
|
};
|
|
#endif
|
|
|
|
// -------------------------------------------------------------
|
|
// Data array for storing ppm (8 channels) pulse widths.
|
|
// -------------------------------------------------------------
|
|
volatile uint16_t ppm[ PPM_ARRAY_MAX ] =
|
|
{
|
|
PPM_PRE_PULSE,
|
|
PPM_SERVO_CENTER, // Channel 1
|
|
PPM_PRE_PULSE,
|
|
PPM_SERVO_CENTER, // Channel 2
|
|
PPM_PRE_PULSE,
|
|
PPM_THROTTLE_DEFAULT, // Channel 3 (throttle)
|
|
PPM_PRE_PULSE,
|
|
PPM_SERVO_CENTER, // Channel 4
|
|
PPM_PRE_PULSE,
|
|
PPM_CH5_MODE_4, // Channel 5
|
|
PPM_PRE_PULSE,
|
|
PPM_SERVO_CENTER, // Channel 6
|
|
PPM_PRE_PULSE,
|
|
PPM_SERVO_CENTER, // Channel 7
|
|
PPM_PRE_PULSE,
|
|
PPM_SERVO_CENTER, // Channel 8
|
|
PPM_PRE_PULSE,
|
|
PPM_PERIOD
|
|
};
|
|
|
|
// -------------------------------------------------------------
|
|
// Data arraw for storing ppm timeout (missing channel detection)
|
|
// -------------------------------------------------------------
|
|
#define PPM_TIMEOUT_VALUE 40 // ~1sec before triggering missing channel detection
|
|
volatile uint8_t ppm_timeout[ PPM_ARRAY_MAX ];
|
|
|
|
// Servo input channel connected status
|
|
#define SERVO_INPUT_CONNECTED_VALUE 100
|
|
volatile uint8_t servo_input_connected[ PPM_ARRAY_MAX ];
|
|
|
|
#ifdef _THROTTLE_LOW_RECOVERY_POSSIBLE
|
|
// count the channels which have been once connected but then got disconnected
|
|
volatile uint8_t disconnected_channels;
|
|
#endif
|
|
|
|
// AVR parameters for PhoneDrone and APM2 boards using ATmega32u2
|
|
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
|
|
|
#define SERVO_DDR DDRB
|
|
#define SERVO_PORT PORTB
|
|
#define SERVO_INPUT PINB
|
|
#define SERVO_INT_VECTOR PCINT0_vect
|
|
#define SERVO_INT_MASK PCMSK0
|
|
#define SERVO_INT_CLEAR_FLAG PCIF0
|
|
#define SERVO_INT_ENABLE PCIE0
|
|
#define SERVO_TIMER_CNT TCNT1
|
|
|
|
#define PPM_DDR DDRC
|
|
#define PPM_PORT PORTC
|
|
#define PPM_OUTPUT_PIN PC6
|
|
#define PPM_INT_VECTOR TIMER1_COMPA_vect
|
|
#define PPM_COMPARE OCR1A
|
|
#define PPM_COMPARE_FLAG COM1A0
|
|
#define PPM_COMPARE_ENABLE OCIE1A
|
|
#define PPM_COMPARE_FORCE_MATCH FOC1A
|
|
|
|
#define USB_DDR DDRC
|
|
#define USB_PORT PORTC
|
|
#define USB_PIN PC2
|
|
|
|
// true if we have received a USB device connect event
|
|
static bool usb_connected;
|
|
|
|
// USB connected event
|
|
void EVENT_USB_Device_Connect(void)
|
|
{
|
|
// Toggle USB pin high if USB is connected
|
|
USB_PORT |= (1 << USB_PIN);
|
|
|
|
usb_connected = true;
|
|
|
|
// this unsets the pin connected to PA1 on the 2560
|
|
// when the bit is clear, USB is connected
|
|
PORTD &= ~1;
|
|
}
|
|
|
|
// USB disconnect event
|
|
void EVENT_USB_Device_Disconnect(void)
|
|
{
|
|
// toggle USB pin low if USB is disconnected
|
|
USB_PORT &= ~(1 << USB_PIN);
|
|
|
|
usb_connected = false;
|
|
|
|
// this sets the pin connected to PA1 on the 2560
|
|
// when the bit is clear, USB is connected
|
|
PORTD |= 1;
|
|
}
|
|
|
|
// AVR parameters for ArduPilot MEGA v1.4 PPM Encoder (ATmega328P)
|
|
#elif defined (__AVR_ATmega328P__) || defined (__AVR_ATmega328__)
|
|
|
|
#define SERVO_DDR DDRD
|
|
#define SERVO_PORT PORTD
|
|
#define SERVO_INPUT PIND
|
|
#define SERVO_INT_VECTOR PCINT2_vect
|
|
#define SERVO_INT_MASK PCMSK2
|
|
#define SERVO_INT_CLEAR_FLAG PCIF2
|
|
#define SERVO_INT_ENABLE PCIE2
|
|
#define SERVO_TIMER_CNT TCNT1
|
|
|
|
#define PPM_DDR DDRB
|
|
#define PPM_PORT PORTB
|
|
#define PPM_OUTPUT_PIN PB2
|
|
#define PPM_INT_VECTOR TIMER1_COMPB_vect
|
|
#define PPM_COMPARE OCR1B
|
|
#define PPM_COMPARE_FLAG COM1B0
|
|
#define PPM_COMPARE_ENABLE OCIE1B
|
|
#define PPM_COMPARE_FORCE_MATCH FOC1B
|
|
|
|
#else
|
|
#error NO SUPPORTED DEVICE FOUND! (ATmega16u2 / ATmega32u2 / ATmega328p)
|
|
#endif
|
|
|
|
// Used to indicate invalid SERVO input signals
|
|
volatile uint8_t servo_input_errors = 0;
|
|
|
|
// Used to indicate missing SERVO input signals
|
|
volatile bool servo_input_missing = true;
|
|
|
|
// Used to indicate if PPM generator is active
|
|
volatile bool ppm_generator_active = false;
|
|
|
|
// Used to indicate a brownout restart
|
|
volatile bool brownout_reset = false;
|
|
|
|
#ifdef _THROTTLE_LOW_FAILSAFE_INDICATION
|
|
// Used to force throttle fail-safe mode (RTL)
|
|
volatile bool throttle_failsafe_force = false;
|
|
#endif
|
|
|
|
// ------------------------------------------------------------------------------
|
|
// PPM GENERATOR START - TOGGLE ON COMPARE INTERRUPT ENABLE
|
|
// ------------------------------------------------------------------------------
|
|
void ppm_start( void )
|
|
{
|
|
// Prevent reenabling an already active PPM generator
|
|
if( ppm_generator_active ) return;
|
|
|
|
// Store interrupt status and register flags
|
|
volatile uint8_t SREG_tmp = SREG;
|
|
|
|
// Stop interrupts
|
|
cli();
|
|
|
|
// Make sure initial output state is low
|
|
PPM_PORT &= ~(1 << PPM_OUTPUT_PIN);
|
|
|
|
// Wait for output pin to settle
|
|
//_delay_us( 1 );
|
|
|
|
// Set initial compare toggle to maximum (32ms) to give other parts of the system time to start
|
|
SERVO_TIMER_CNT = 0;
|
|
PPM_COMPARE = 0xFFFF;
|
|
|
|
// Set toggle on compare output
|
|
TCCR1A = (1 << PPM_COMPARE_FLAG);
|
|
|
|
// Set TIMER1 8x prescaler
|
|
TCCR1B = ( 1 << CS11 );
|
|
|
|
#if defined (_POSITIVE_PPM_FRAME_)
|
|
// Force output compare to reverse polarity
|
|
TCCR1C |= (1 << PPM_COMPARE_FORCE_MATCH);
|
|
#endif
|
|
|
|
// Enable output compare interrupt
|
|
TIMSK1 |= (1 << PPM_COMPARE_ENABLE);
|
|
|
|
// Indicate that PPM generator is active
|
|
ppm_generator_active = true;
|
|
|
|
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
|
// Turn on TX led if PPM generator is active
|
|
PORTD &= ~( 1<< PD5 );
|
|
#endif
|
|
|
|
// Restore interrupt status and register flags
|
|
SREG = SREG_tmp;
|
|
}
|
|
|
|
// ------------------------------------------------------------------------------
|
|
// PPM GENERATOR STOP - TOGGLE ON COMPARE INTERRUPT DISABLE
|
|
// ------------------------------------------------------------------------------
|
|
void ppm_stop( void )
|
|
{
|
|
// Store interrupt status and register flags
|
|
volatile uint8_t SREG_tmp = SREG;
|
|
|
|
// Stop interrupts
|
|
cli();
|
|
|
|
// Disable output compare interrupt
|
|
TIMSK1 &= ~(1 << PPM_COMPARE_ENABLE);
|
|
|
|
// Reset TIMER1 registers
|
|
TCCR1A = 0;
|
|
TCCR1B = 0;
|
|
|
|
// Indicate that PPM generator is not active
|
|
ppm_generator_active = false;
|
|
|
|
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
|
// Turn off TX led if PPM generator is off
|
|
PORTD |= ( 1<< PD5 );
|
|
#endif
|
|
|
|
// Restore interrupt status and register flags
|
|
SREG = SREG_tmp;
|
|
}
|
|
|
|
// ------------------------------------------------------------------------------
|
|
// Watchdog Interrupt (interrupt only mode, no reset)
|
|
// ------------------------------------------------------------------------------
|
|
ISR( WDT_vect ) // If watchdog is triggered then enable missing signal flag and copy power on or failsafe positions
|
|
{
|
|
// Use failsafe values if PPM generator is active or if chip has been reset from a brown-out
|
|
if ( ppm_generator_active || brownout_reset )
|
|
{
|
|
// Copy failsafe values to ppm[..]
|
|
//for( uint8_t i = 0; i < PPM_ARRAY_MAX; i++ )
|
|
//{
|
|
// ppm[ i ] = failsafe_ppm[ i ];
|
|
//}
|
|
|
|
// Set Throttle Low & leave other channels at last value
|
|
ppm[5] = failsafe_ppm[ 5 ];
|
|
}
|
|
|
|
// If we are in PPM passtrough mode and a input signal has been detected, or if chip has been reset from a brown_out then start the PPM generator.
|
|
if( ( servo_input_mode == PPM_PASSTROUGH_MODE && servo_input_missing == false ) || brownout_reset )
|
|
{
|
|
// Start PPM generator
|
|
ppm_start();
|
|
brownout_reset = false;
|
|
}
|
|
|
|
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
|
// Turn on RX led if signal is missing
|
|
if( !servo_input_missing )
|
|
{
|
|
PORTD &= ~( 1<< PD4 );
|
|
}
|
|
#endif
|
|
|
|
// Set missing receiver signal flag
|
|
servo_input_missing = true;
|
|
|
|
// Reset servo input error flag
|
|
servo_input_errors = 0;
|
|
|
|
}
|
|
// ------------------------------------------------------------------------------
|
|
|
|
|
|
// ------------------------------------------------------------------------------
|
|
// SERVO/PPM INPUT - PIN CHANGE INTERRUPT
|
|
// ------------------------------------------------------------------------------
|
|
ISR( SERVO_INT_VECTOR )
|
|
{
|
|
// Servo pulse start timing
|
|
static uint16_t servo_start[ PPM_ARRAY_MAX ] = { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }; // We sacrefice some memory but save instructions by working with ppm index count (18) instead of input channel count (8)
|
|
|
|
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
|
// Toggle LED delay
|
|
static uint8_t led_delay = 0;
|
|
#endif
|
|
|
|
// Servo input pin storage
|
|
static uint8_t servo_pins_old = 0;
|
|
|
|
// Used to store current servo input pins
|
|
uint8_t servo_pins;
|
|
|
|
uint8_t servo_change;
|
|
uint8_t servo_pin;
|
|
uint8_t ppm_channel;
|
|
|
|
// Read current servo pulse change time
|
|
uint16_t servo_time = SERVO_TIMER_CNT;
|
|
|
|
// ------------------------------------------------------------------------------
|
|
// PPM passtrough mode ( signal passtrough from channel 1 to ppm output pin)
|
|
// ------------------------------------------------------------------------------
|
|
if( servo_input_mode == PPM_PASSTROUGH_MODE )
|
|
{
|
|
// Has watchdog timer failsafe started PPM generator? If so we need to stop it.
|
|
if( ppm_generator_active )
|
|
{
|
|
// Stop PPM generator
|
|
ppm_stop();
|
|
}
|
|
|
|
// PPM (channel 1) input pin is high
|
|
if( SERVO_INPUT & 1 )
|
|
{
|
|
// Set PPM output pin high
|
|
PPM_PORT |= (1 << PPM_OUTPUT_PIN);
|
|
}
|
|
// PPM (channel 1) input pin is low
|
|
else
|
|
{
|
|
// Set PPM output pin low
|
|
PPM_PORT &= ~(1 << PPM_OUTPUT_PIN);
|
|
}
|
|
|
|
// Reset Watchdog Timer
|
|
#ifndef _PPM_PASSTROUGH_MODE_DISABLE_FAILSAFE_
|
|
wdt_reset();
|
|
#endif
|
|
|
|
// Set servo input missing flag false to indicate that we have received servo input signals
|
|
servo_input_missing = false;
|
|
|
|
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
|
// Toggle TX LED at PPM passtrough
|
|
if( ++led_delay > 128 ) // Toggle every 128th pulse
|
|
{
|
|
// Toggle TX led
|
|
PIND |= ( 1<< PD5 );
|
|
led_delay = 0;
|
|
}
|
|
#endif
|
|
|
|
// Leave interrupt
|
|
return;
|
|
}
|
|
// ------------------------------------------------------------------------------
|
|
// SERVO PWM MODE
|
|
// ------------------------------------------------------------------------------
|
|
|
|
//CHECK_PINS_START: // Start of servo input check
|
|
|
|
// Store current servo input pins
|
|
servo_pins = SERVO_INPUT;
|
|
|
|
// Calculate servo input pin change mask
|
|
servo_change = servo_pins ^ servo_pins_old;
|
|
|
|
// Set initial servo pin and ppm[..] index
|
|
servo_pin = 1;
|
|
ppm_channel = 1;
|
|
|
|
CHECK_PINS_LOOP: // Input servo pin check loop
|
|
|
|
// Check for pin change on current servo channel
|
|
if( servo_change & servo_pin )
|
|
{
|
|
// Remove processed pin change from bitmask
|
|
servo_change &= ~servo_pin;
|
|
|
|
// High (raising edge)
|
|
if( servo_pins & servo_pin )
|
|
{
|
|
servo_start[ ppm_channel ] = servo_time;
|
|
}
|
|
else
|
|
{
|
|
// Get servo pulse width
|
|
uint16_t servo_width = servo_time - servo_start[ ppm_channel ] - PPM_PRE_PULSE;
|
|
|
|
// Check that servo pulse signal is valid before sending to ppm encoder
|
|
if( servo_width > PPM_SERVO_MAX ) goto CHECK_PINS_ERROR;
|
|
if( servo_width < PPM_SERVO_MIN ) goto CHECK_PINS_ERROR;
|
|
|
|
// Reset Watchdog Timer
|
|
wdt_reset();
|
|
|
|
// Set servo input missing flag false to indicate that we have received servo input signals
|
|
servo_input_missing = false;
|
|
|
|
// Count valid signals to mark channel active
|
|
if( servo_input_connected[ ppm_channel ] < SERVO_INPUT_CONNECTED_VALUE )
|
|
{
|
|
servo_input_connected[ ppm_channel ]++;
|
|
}
|
|
|
|
//Reset ppm single channel fail-safe timeout
|
|
ppm_timeout[ ppm_channel ] = 0;
|
|
|
|
#ifdef _THROTTLE_LOW_FAILSAFE_INDICATION
|
|
// Check for forced throttle fail-safe
|
|
if( throttle_failsafe_force )
|
|
{
|
|
if( ppm_channel == 5 )
|
|
{
|
|
// Force throttle fail-safe
|
|
servo_width = PPM_THROTTLE_FAILSAFE;
|
|
}
|
|
}
|
|
#endif
|
|
|
|
#ifdef _AVERAGE_FILTER_
|
|
// Average filter to smooth input jitter
|
|
servo_width += ppm[ ppm_channel ];
|
|
servo_width >>= 1;
|
|
#endif
|
|
|
|
#ifdef _JITTER_FILTER_
|
|
// 0.5us cut filter to remove input jitter
|
|
int16_t ppm_tmp = ppm[ ppm_channel ] - servo_width;
|
|
if( ppm_tmp <= _JITTER_FILTER_ && ppm_tmp >= -_JITTER_FILTER_ ) goto CHECK_PINS_NEXT;
|
|
#endif
|
|
|
|
// Update ppm[..]
|
|
ppm[ ppm_channel ] = servo_width;
|
|
}
|
|
}
|
|
|
|
CHECK_PINS_NEXT:
|
|
|
|
// Are we done processing pins?
|
|
if( servo_change )
|
|
{
|
|
// Select next ppm[..] index
|
|
ppm_channel += 2;
|
|
|
|
// Select next servo pin
|
|
servo_pin <<= 1;
|
|
|
|
// Check next pin
|
|
goto CHECK_PINS_LOOP;
|
|
}
|
|
|
|
// All changed pins have been checked
|
|
goto CHECK_PINS_DONE;
|
|
|
|
CHECK_PINS_ERROR:
|
|
|
|
// Used to indicate invalid servo input signals
|
|
servo_input_errors++;
|
|
|
|
goto CHECK_PINS_NEXT;
|
|
|
|
// Processing done, cleanup and exit
|
|
CHECK_PINS_DONE:
|
|
|
|
// Start PPM generator if not already running
|
|
if( !ppm_generator_active ) ppm_start();
|
|
|
|
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
|
|
|
// Toggle RX LED when finished receiving servo pulses
|
|
if( ++led_delay == 0 ) // Toggle led every 128th or 255th interval
|
|
{
|
|
PIND |= ( 1<< PD4 );
|
|
|
|
// Fast toggle on servo input errors
|
|
if( servo_input_errors > _INPUT_ERROR_TRIGGER_ )
|
|
{
|
|
led_delay = 223;
|
|
}
|
|
}
|
|
#endif
|
|
|
|
// Store current servo input pins for next check
|
|
servo_pins_old = servo_pins;
|
|
|
|
//Has servo input changed while processing pins, if so we need to re-check pins
|
|
//if( servo_pins != SERVO_INPUT ) goto CHECK_PINS_START;
|
|
|
|
// Clear interrupt event from already processed pin changes
|
|
//PCIFR |= (1 << SERVO_INT_CLEAR_FLAG);
|
|
}
|
|
// ------------------------------------------------------------------------------
|
|
|
|
|
|
// ------------------------------------------------------------------------------
|
|
// PPM OUTPUT - TIMER1 COMPARE INTERRUPT
|
|
// ------------------------------------------------------------------------------
|
|
// Current active ppm channel
|
|
volatile uint8_t ppm_out_channel = PPM_ARRAY_MAX - 1;
|
|
ISR( PPM_INT_VECTOR, ISR_NOBLOCK )
|
|
{
|
|
// ------------------------------------------------------------------------------
|
|
// !! NESTED INTERRUPT !!
|
|
// - ALL VARIABLES SHOULD BE GLOBAL VOLATILE
|
|
// - ACCESSING VARIABLES >8BIT MUST BE DONE ATOMIC USING CLI/SEI
|
|
// ------------------------------------------------------------------------------
|
|
|
|
// Update timing for next compare toggle with either current ppm input value, or fail-safe value if there is a channel timeout.
|
|
if( ppm_timeout[ ppm_out_channel ] > PPM_TIMEOUT_VALUE )
|
|
{
|
|
// Channel 1-4?
|
|
if( ppm_out_channel < 8 )
|
|
{
|
|
// Channel 1-4 - Use fail-safe value
|
|
cli();
|
|
PPM_COMPARE += failsafe_ppm[ ppm_out_channel ];
|
|
sei();
|
|
|
|
// Channel 3
|
|
if( ppm_out_channel == 5 )
|
|
{
|
|
// report this to the LED indication
|
|
servo_input_missing = true;
|
|
}
|
|
}
|
|
else
|
|
{
|
|
// Channel 5-8 - Use last known value
|
|
cli();
|
|
PPM_COMPARE += ppm[ ppm_out_channel ];
|
|
sei();
|
|
}
|
|
|
|
#if defined _THROTTLE_LOW_RECOVERY_POSSIBLE && defined _THROTTLE_LOW_FAILSAFE_INDICATION
|
|
// Count the channel that we have lost
|
|
disconnected_channels++;
|
|
#elif defined _THROTTLE_LOW_FAILSAFE_INDICATION
|
|
throttle_failsafe_force = true;
|
|
#endif
|
|
|
|
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
|
// Turn on RX LED to indicate a fail-safe condition
|
|
PORTD &= ~(1 << PD4);
|
|
#endif
|
|
}
|
|
else
|
|
{
|
|
// Use latest ppm input value
|
|
cli();
|
|
PPM_COMPARE += ppm[ ppm_out_channel ];
|
|
sei();
|
|
|
|
// Increment active channel timeout (reset to zero in input interrupt each time a valid signal is detected)
|
|
if( servo_input_connected[ ppm_out_channel ] >= SERVO_INPUT_CONNECTED_VALUE )
|
|
{
|
|
ppm_timeout[ ppm_out_channel ]++;
|
|
}
|
|
}
|
|
|
|
if( ++ppm_out_channel >= PPM_ARRAY_MAX )
|
|
{
|
|
ppm_out_channel = 0;
|
|
|
|
#ifdef _THROTTLE_LOW_RECOVERY_POSSIBLE
|
|
// Did we lose one or more active servo input channel? If so force throttle fail-safe (RTL)
|
|
if( disconnected_channels > 0 )
|
|
{
|
|
throttle_failsafe_force = true;
|
|
disconnected_channels = 0;
|
|
}
|
|
else
|
|
{
|
|
throttle_failsafe_force = false;
|
|
}
|
|
#endif
|
|
|
|
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
|
// Blink TX LED when PPM generator has finished a pulse train
|
|
PIND |= ( 1<< PD5 );
|
|
#endif
|
|
}
|
|
}
|
|
// ------------------------------------------------------------------------------
|
|
|
|
// ------------------------------------------------------------------------------
|
|
// PPM READ - INTERRUPT SAFE PPM SERVO CHANNEL READ
|
|
// ------------------------------------------------------------------------------
|
|
uint16_t ppm_read_channel( uint8_t channel )
|
|
{
|
|
// Limit channel to valid value
|
|
uint8_t _channel = channel;
|
|
if( _channel == 0 ) _channel = 1;
|
|
if( _channel > SERVO_CHANNELS ) _channel = SERVO_CHANNELS;
|
|
|
|
// Calculate ppm[..] position
|
|
uint8_t ppm_index = ( _channel << 1 ) + 1;
|
|
|
|
// Read ppm[..] in a non blocking interrupt safe manner
|
|
uint16_t ppm_tmp = ppm[ ppm_index ];
|
|
while( ppm_tmp != ppm[ ppm_index ] ) ppm_tmp = ppm[ ppm_index ];
|
|
|
|
// Return as normal servo value
|
|
return ppm_tmp + PPM_PRE_PULSE;
|
|
}
|
|
// ------------------------------------------------------------------------------
|
|
|
|
// ------------------------------------------------------------------------------
|
|
// PPM ENCODER INIT
|
|
// ------------------------------------------------------------------------------
|
|
void ppm_encoder_init( void )
|
|
{
|
|
// ATmegaXXU2 only init code
|
|
// ------------------------------------------------------------------------------
|
|
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
|
// ------------------------------------------------------------------------------
|
|
// Reset Source checkings
|
|
// ------------------------------------------------------------------------------
|
|
if (MCUSR & 1) // Power-on Reset
|
|
{
|
|
MCUSR=0; // Clear MCU Status register
|
|
// custom code here
|
|
}
|
|
else if (MCUSR & 2) // External Reset
|
|
{
|
|
MCUSR=0; // Clear MCU Status register
|
|
// custom code here
|
|
}
|
|
else if (MCUSR & 4) // Brown-Out Reset
|
|
{
|
|
MCUSR=0; // Clear MCU Status register
|
|
brownout_reset=true;
|
|
// Make sure PPM generator will always start directly with throttle F/S value (900us) after a brown-out reset
|
|
ppm[5] = failsafe_ppm[ 5 ];
|
|
}
|
|
else // Watchdog Reset
|
|
{
|
|
MCUSR=0; // Clear MCU Status register
|
|
// custom code here
|
|
}
|
|
|
|
// APM USB connection status UART MUX selector pin
|
|
// ------------------------------------------------------------------------------
|
|
USB_DDR |= (1 << USB_PIN); // Set USB pin to output
|
|
|
|
DDRD |= (1<<PD4); // RX LED OUTPUT
|
|
DDRD |= (1<<PD5); // TX LED OUTPUT
|
|
|
|
PORTD |= (1<<PD4); // RX LED OFF
|
|
PORTD |= (1<<PD5); // TX LED OFF
|
|
#endif
|
|
|
|
|
|
// USE JUMPER TO CHECK FOR PWM OR PPM PASSTROUGH MODE (channel 2&3 shorted)
|
|
// ------------------------------------------------------------------------------
|
|
if( servo_input_mode == JUMPER_SELECT_MODE )
|
|
{
|
|
// channel 3 status counter
|
|
uint8_t channel3_status = 0;
|
|
|
|
// Set channel 3 to input
|
|
SERVO_DDR &= ~(1 << 2);
|
|
|
|
// Enable channel 3 pullup
|
|
SERVO_PORT |= (1 << 2);
|
|
|
|
// Set channel 2 to output
|
|
SERVO_DDR |= (1 << 1);
|
|
|
|
// Set channel 2 output low
|
|
SERVO_PORT &= ~(1 << 1);
|
|
|
|
_delay_us (10);
|
|
|
|
// Increment channel3_status if channel 3 is set low by channel 2
|
|
if( ( SERVO_INPUT & (1 << 2) ) == 0 ) channel3_status++;
|
|
|
|
// Set channel 2 output high
|
|
SERVO_PORT |= (1 << 1);
|
|
|
|
_delay_us (10);
|
|
|
|
// Increment channel3_status if channel 3 is set high by channel 2
|
|
if( ( SERVO_INPUT & (1 << 2) ) != 0 ) channel3_status++;
|
|
|
|
// Set channel 2 output low
|
|
SERVO_PORT &= ~(1 << 1);
|
|
|
|
_delay_us (10);
|
|
|
|
// Increment channel3_status if channel 3 is set low by channel 2
|
|
if( ( SERVO_INPUT & (1 << 2) ) == 0 ) channel3_status++;
|
|
|
|
// Set servo input mode based on channel3_status
|
|
if( channel3_status == 3 ) servo_input_mode = PPM_PASSTROUGH_MODE;
|
|
else servo_input_mode = SERVO_PWM_MODE;
|
|
|
|
}
|
|
|
|
|
|
// SERVO/PPM INPUT PINS
|
|
// ------------------------------------------------------------------------------
|
|
// Set all servo input pins to inputs
|
|
SERVO_DDR = 0;
|
|
|
|
// Activate pullups on all input pins
|
|
SERVO_PORT |= 0xFF;
|
|
|
|
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
|
// on 32U2 set PD0 to be an output, and clear the bit. This tells
|
|
// the 2560 that USB is connected. The USB connection event fires
|
|
// later to set the right value
|
|
DDRD |= 1;
|
|
if (usb_connected) {
|
|
PORTD &= ~1;
|
|
} else {
|
|
PORTD |= 1;
|
|
}
|
|
#endif
|
|
|
|
// PPM PASS-THROUGH MODE
|
|
if( servo_input_mode == PPM_PASSTROUGH_MODE )
|
|
{
|
|
// Set servo input interrupt pin mask to servo input channel 1
|
|
SERVO_INT_MASK = 0x01;
|
|
}
|
|
|
|
// SERVO PWM INPUT MODE
|
|
// ------------------------------------------------------------------------------
|
|
if( servo_input_mode == SERVO_PWM_MODE )
|
|
{
|
|
// Interrupt on all input pins
|
|
SERVO_INT_MASK = 0xFF;
|
|
}
|
|
|
|
// Enable servo input interrupt
|
|
PCICR |= (1 << SERVO_INT_ENABLE);
|
|
|
|
// PPM OUTPUT
|
|
// ------------------------------------------------------------------------------
|
|
// PPM generator (PWM output timer/counter) is started either by pin change interrupt or by watchdog interrupt
|
|
|
|
// Set PPM pin to output
|
|
PPM_DDR |= (1 << PPM_OUTPUT_PIN);
|
|
|
|
// ------------------------------------------------------------------------------
|
|
// Enable watchdog interrupt mode
|
|
// ------------------------------------------------------------------------------
|
|
#ifdef _PPM_PASSTROUGH_MODE_DISABLE_FAILSAFE_
|
|
if( servo_input_mode != PPM_PASSTROUGH_MODE )
|
|
#endif
|
|
{
|
|
// Disable watchdog
|
|
wdt_disable();
|
|
// Reset watchdog timer
|
|
wdt_reset();
|
|
// Start timed watchdog setup sequence
|
|
WDTCSR |= (1<<WDCE) | (1<<WDE );
|
|
// Set 250 ms watchdog timeout and enable interrupt
|
|
WDTCSR = (1<<WDIE) | (1<<WDP2);
|
|
}
|
|
}
|
|
// ------------------------------------------------------------------------------
|